2015 Lexus CT200h Navigation Manual (in English)

88
1. BASIC OPERATION
CT200h_Navi_OM76146U_(U)14.06.17 09:48
1Select , or .
X North-up screen
X Heading-up screen
X 3D screen : North-up symbol
Regardless of the direction of vehicle travel,
north is always up.
: Heading-up symbol
The direction of vehicle travel is always up.
: 3D Heading-up symbol
The direction of vehicle travel is always up.z The letter(s) beside this symbol indicate the
vehicle’s heading direction (e.g. N for
north).
ORIENTATION OF THE MAP
The orientation of the map can be
changed between 2D north-up, 2D
heading-up and 3D heading-up by se-
lecting the orientation symbol displayed
at the top left of the screen.

89
1. BASIC OPERATION
3
NAVIGATION SYSTEM
CT200h_Navi_OM76146U_(U)14.06.17 09:48
1Select “Options” on the map screen.
2Select “Map Mode”.
3Select the desired configuration button.
zDepending on the conditions, certain
screen configuration buttons cannot be
selected.
SWITCHING THE MAP MODENo.FunctionPage
Select to display the single
map screen. 90
Select to display the dual
map screen.90
Select to display the com-
pass mode screen.91
Select to display the turn list
screen.130
Select to display the freeway
exit list screen.128
Select to display the inter-
section guidance screen or
the guidance screen on the
freeway.
130
Select to display the turn-
by-turn arrow screen.131

90
1. BASIC OPERATION
CT200h_Navi_OM76146U_(U)14.06.17 09:48
■MAP ONLY
■ DUAL MAP
zThe map on the left is the main map.
X Editing right map
1Select any point on the right side map.
2Select the desired item.
zWhen set to on, the indicator will illuminate.
The right side map can be edited.
No.FunctionPage
Select to change the orien-
tation of the map.88
Select to display POI icons.94
Select to show traffic infor-
mation. 100
Select to display eDestina-
tion icons.374
Select to change the map
scale.86

91
1. BASIC OPERATION
3
NAVIGATION SYSTEM
CT200h_Navi_OM76146U_(U)14.06.17 09:48
■COMPASS
Information about the destination, cur-
rent position and a compass is displayed
on the screen.
INFORMATION
●
The destination mark is displayed in the
direction of the destination. When driv-
ing, refer to the longitude and latitude
coordinates, and the compass, to make
sure that the vehicle is headed in the
direction of the destination.
●When the vehicle travels out of the cover-
age area, the guidance screen changes to
the whole compass mode screen.
SCREEN SCROLL
OPERATION
Use the scroll feature to move the de-
sired point to the center of the screen for
looking at a point on the map that is dif-
ferent from the current position.
No.Information/Function
Cursor mark
Distance from the current position to
the cursor mark.
Select to set as a destination.
When selecting “Go to ” on the fol-
lowing map screen, the navigation
system performs a search for the
route. ( →P.121)
If a destination has already been set,
“Go to ” and “Add to Route” will be
displayed.
“Go to ” : Select to delete the exist-
ing destination(s) and set a new one.
“Add to Route” : Select to add a desti-
nation.
Select to register as a memory point.
To change the icon, name, etc.:→P.144
Select to return to the current posi-
tion.

92
1. BASIC OPERATION
CT200h_Navi_OM76146U_(U)14.06.17 09:48
zTo scroll over the map screen, place the
cursor mark in the desired position and
then press and hold the Remote Touch
knob. The map will cont inue scrolling in that
direction until the knob is released.
1Select one of the 8 directional arrows to
move the cursor to the desired point
and then select “OK”.
ADJUSTING LOCATION IN
SMALL INCREMENTS
The cursor location can be adjusted in
small increments when “Adjust
Location” is selected on the setting map
screen.
Also, when changing the location of
memory points on the editing screen
( → P.146) and adjusting the current po-
sition mark manually on the “Calibration”
screen ( →P.155), 8 directional arrows
may appear for this purpose.

93
1. BASIC OPERATION
CT200h_Navi_OM76146U_(U)14.06.17 09:48
3
NAVIGATION SYSTEM
3. MAP SCREEN INFORMATION
1Select “Options” on the map screen.
2Select “Map Information” .
3Select the desired items to be displayed.
zWhen set to on, the indicator will illuminate.
DISPLAYING MAP
INFORMATION
Information such as POI icons, route
trace, speed limit, etc. can be displayed
on the map screen.
No.FunctionPage
Select to display the select-
ed POI icons.
Select to select or change
POI icons.94
Select to display eDestina-
tion icons.374
Select to display route trace.96
Select to display traffic infor-
mation.100
Select to display speed limit
icon.

94
1. BASIC OPERATION
CT200h_Navi_OM76146U_(U)14.06.17 09:48
1Display the “Map Information” screen.
(→ P.93)
2Select “Select POI” .
zWhen the POI icons to be displayed on the
map screen have already been set,
“Change POI” is displayed.
3Select the desired POI category and se-
lect “OK” .SELECTING THE POI ICONS
No.Information/FunctionPage
Displays up to 5 selected
POI icons on the map
screen.−
Select to cancel the select-
ed POI icons.−
Displays up to 6 POI icons
as favorite POI categories153
Select to display other POI
categories if the desired
POIs cannot be found on
the screen.
95
Select to search for the
nearest POIs.95

95
1. BASIC OPERATION
3
NAVIGATION SYSTEM
CT200h_Navi_OM76146U_(U)14.06.17 09:48
■SELECTING OTHER POI ICONS
TO BE DISPLAYED
1Select “Other POIs” .
2Select the desired POI categories and
select “OK”.
“List All Categories” : Select to display all
POI categories. To add more POI catego-
ries, select “More”.
■DISPLAYING THE LOCAL POI
LIST
1Select “Find Local POI” .
2Select the desired POI.
“Near...” : Select to search for POIs near the
current position or along the route.
3Check that the selected POI is dis-
played on the map screen. ( →P.91)
POIs that are within 20 miles (32 km) of
the current position will be listed from
among the selected categories.