2015 JEEP WRANGLER bulb

▫Automatic Transmission — If Equipped.....619
▫Clutch Hydraulic System (Manual Transmission)
— If Equipped.......................623
▫Manual Transmission — If Equipped.......623
▫Transfer Case........................624
▫Front/Rear Axle Fluid..................625
▫Appearance Care And Protection From
Corrosion...........................625
!FUSES..............................633
▫Totally Integrated Power Module..........634
!VEHICLE STORAGE....................640
!REPLACEMENT BULBS.................641
!BULB REPLACEMENT..................642
▫Headlamp..........................642
▫Front Park/Turn Signal.................643
▫Front Side Marker.....................643
▫Front Fog Lamp......................644
▫Rear Tail, Stop, Turn Signal, And Backup
Lamp.............................644
▫Center High-Mounted Stop Lamp (CHMSL) . . .645
!FLUID CAPACITIES....................646
!FLUIDS, LUBRICANTS AND GENUINE
PA R T S . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..647
▫Engine.............................647
▫Chassis............................649
582 MAINTAINING YOUR VEHICLE

the message will appear the next time the vehicle is
started. This might indicate a damaged cap. If the prob-
lem is detected twice in a row, the system will turn on the
MIL. Resolving the problem will turn the MIL off.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not
on when the engine is running, and that the OBD II
system is ready for testing.
Normally, the OBD II system will be ready. The OBD II
system maynotbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition actuated test, which
you can use prior to going to the test station. To check if
your vehicle’s OBD II system is ready, you must do the
following:
1. Cycle the ignition switch to the ON position, but do
not crank or start the engine.
NOTE:If you crank or start the engine, you will have to
start this test over.
2. As soon as you cycle the ignition switch to the ON
position, you will see the MIL symbol come on as part
of a normal bulb check.
7
MAINTAINING YOUR VEHICLE 585

REPLACEMENT BULBS
Interior Bulbs
Bulb Number
Automatic Transmission Indicator Lamp658
Heater Control Lamps (2)194
Rocker Switch Indicator Lamp (Rear Window Defog-
ger, and Rear Wash/Wipe)
**
Soundbar Dome Lamp912
** Bulbs only available from authorized dealer.
Exterior Bulbs
Bulb Number
Headlamps (2)H13
Front Park/Turn Signal Lamps (2)3157NA
Front Side Marker Lamps (2)168
Fog LampsPSX24W
7
MAINTAINING YOUR VEHICLE 641

Bulb Number
Rear Stop/Tail/Turn Lamps (2)3157
Center High-Mounted Stop LampL.E.D.
Backup Lamps (2)3157
License Lamp194
NOTE:Numbers refer to commercial bulb types that can be purchased from your local authorized dealer.
If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable Service Manual.
BULB REPLACEMENT
NOTE:Lens fogging can occur under certain atmo-
spheric conditions. This will usually clear as atmospheric
conditions change to allow the condensation to change
back into a vapor. Turning the lamps on will usually
accelerate the clearing process.
Headlamp
1. Open hood and support using prop rod.
2. Remove the front grille. Turn the retainers along the
top 1/4 turn counterclockwise and remove.
3. Pull the bottom of the grille away starting at one side
and working toward the other.
4. Turn both park and turn signal socket assemblies 1/4
turn counterclockwise and remove.
642 MAINTAINING YOUR VEHICLE

5. Remove the four screws holding the metal retaining
ring.
6. Remove the lamp from the collar.
7. Grasp the bulb and turn 1/4 turn counterclockwise.
8. Pull the bulb from the housing.
9. Push connector locking tab to the unlock position.
10. Remove connector from bulb.
11. Push connector onto new bulb base, and push the
connector locking tab to the lock position.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
12. Reinstall bulb housing. Rotate the bulb 1/4 turn
clockwise.
Front Park/Turn Signal
1. Remove the front grille. Turn the retainers along the
top 1/4 turn counterclockwise and remove.
2. Pull the bottom of the grille away starting at one side
and working toward the other.
3. Turn the socket assembly 1/4 turn counterclockwise
and remove from housing. Pull the bulb straight from
the socket to replace.
Front Side Marker
1. Reach under the front fender flare and locate the front
side marker socket.
2. Turn the socket assembly counterclockwise 1/3 turn
and remove it from the housing. Pull the bulb straight
from the socket to replace.
7
MAINTAINING YOUR VEHICLE 643

Front Fog Lamp
1. Reach under the vehicle to access the back of the front
fog lamp.
2. Disconnect the wire harness connector from the front
fog lamp connector receptacle.
3. Firmly grasp the bulb by the two latch features and
squeeze them together to unlock the bulb from the
back of the front fog lamp housing.
4. Pull the bulb straight out from the keyed opening in
the housing and then connect the replacement bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
Rear Tail, Stop, Turn Signal, And Backup Lamp
1. Remove the two inboard screws attaching the tail light
housing to the body.DO NOT REMOVE THE OUT-
BOARD SCREWS AT ANY TIME.
Inboard Screw Location
644 MAINTAINING YOUR VEHICLE

2. Separate the housing from the body by pushing the
lamp inboard while pulling the lamp away from the
body.
3. Rotate the appropriate socket 1/4 turn counterclock-
wise, then remove it from the housing.
4. Pull the bulb straight from the socket to replace.
Center High-Mounted Stop Lamp (CHMSL)
The stop lamp is mounted on a bracket that extends
upward from the tailgate behind the spare tire. If service
is needed, obtain the LED/Cover Assembly from your
local authorized dealer.
1. Remove the spare tire.
2. Remove the four screws holding the lens/cover in
place on the spare tire carrier.
3. Disconnect the wire harness from the back of the LED
cover.
7
MAINTAINING YOUR VEHICLE 645

Auto Down Power Windows..................45
Automatic Dimming Mirror..................112
Automatic Door Locks......................41
Automatic Headlights......................168
Automatic Oil Change Indicator...............331
Automatic Temperature Control (ATC)..........404
Automatic Transmission....................431
Adding Fluid..........................622
Fluid and Filter Changes..................622
Fluid Change..........................622
Fluid Level Check.......................620
Fluid Type............................619
Special Additives.......................620
Autostick...............................439
Auxiliary Electrical Outlet (Power Outlet)........183
Auxiliary Power Outlet.....................183
Axle Fluid..............................649
Axle Lock...............................446
Battery.................................596
Keyless Transmitter Replacement (RKE)........27
Belts, Seat...............................101
Body Mechanism Lubrication.................601
B-Pillar Location..........................493
Brake Assist System.......................471
Brake Control System, Electronic..............469
Brake Fluid.............................649
Brakes.................................468
Brake System............................468
Anti-Lock (ABS)........................469
Master Cylinder........................618
Parking..............................466
Warning Light.........................307
Brake/Transmission Interlock.................431
Bulb Replacement.........................641
Bulbs, Light.............................103
Calibration, Compass......................32510
INDEX 673