2015 FIAT DUCATO BASE CAMPER light

REPLACING AN
EXTERIOR BULB
For the type of bulb and power
rating, see “Replacing a bulb”.
FRONT LIGHT
CLUSTERS
The front light clusters contain the
side lights and DRLs (where the
LED solution is not provided),
dipped beam, main beam and
direction indicator bulbs.
Bulbs must be replaced with the
headlight removed and placed on a
work surface.
To remove the headlight, operate as
follows:
❒open the bonnet following the
procedure in the "Bonnet/Luggage
Compartment" paragraph in the
"Knowing your car" chapter;
❒disconnect the electrical connector A
fig. 202 from the headlight;
❒undo the screws B fig. 203 fixing the
headlight to the body, release the
headlight from its housing, in the
lower part, as shown in fig. 203 and
remove the headlight placing it on
a work surface;❒follow the steps described below for
replacing the bulbs;
❒after the replacement fit the
headlight, fastening it with the fixing
screws B fig. 203;
❒connect the electrical connector A
fig. 202 to the headlight.
The bulbs are arranged inside the
light cluster as follows fig. 204:
A Direction indicatorsB Dipped beam headlights
C Main beam headlights
D Side lights/daytime running lights
E Side lights/DRLs with LEDs (as
an alternative to D)
To replace a bulb of the main beam
headlights, remove rubber cap C
fig. 205.
To replace a bulb of the dipped
beam headlights, remove rubber
cap B fig. 205.
To replace the bulb of the direction
indicators and side lights/DRLs
(when not provided with LEDs)
remove rubber cap A fig. 205.
After replacement, refit the rubber
caps correctly, ensuring that they
are locked in place.
202F1A0337
203F1A0338
204F1A0313
211

SIDE LIGHTS/DAYTIME
RUNNING LIGHTS
(LEDs)
These are LEDs. For replacement,
contact a Fiat Dealership.
SIDE LIGHTS/DAYTIME
RUNNING LIGHTS
To replace the bulb, proceed as
follows:
❒remove the protective rubber cover A
fig. 205;
❒turn the bulb holder B fig. 206
anticlockwise;
❒extract the bulb by pulling and
replace it;
❒remove the bulb by pushing it slightly
and turning it anticlockwise (bayonet
mount);❒refit the bulb holder B by turning it
clockwise and making sure that it
locks correctly
❒refit the protective rubber cover A fig.
205.
MAIN BEAM
HEADLIGHTS
To replace the bulb, proceed as
follows:
❒remove the protective rubber cover C
fig. 205;❒release the bulb holder A fig. 207
from the side clips B and remove it;
❒disconnect the electrical connector;
❒fit the new bulb, ensuring that the
outline of the metal part coincides
with the grooves on the curve of the
headlight, pressing to engage it
with the side clips;
❒reconnect the electrical connector;
❒refit the protective rubber cover C fig.
205.
DIPPED HEADLIGHTS
With incandescent
bulbs
To replace the bulb, proceed as
follows:
205F1A0314
206F1A0386
207F1A0315
208F1A0316
212
IN AN EMERGENCY
❒remove the protective rubber cover B
fig. 205;

❒release the bulb holder A fig. 208
from the side clips B and remove it;
❒disconnect the electrical connector;
❒fit the new bulb, ensuring that the
outline of the metal part coincides
with the grooves on the curve of the
headlight, pressing to engage it
with the side clips;
❒reconnect the electrical connector;
❒refit the protective rubber cover B fig.
205.
DIRECTION
INDICATORS
To replace the bulb, proceed as
follows:
❒remove the protective rubber cover A
fig. 205;
❒turn the bulb holder B fig. 209
anticlockwise;
❒extract the bulb by pulling and
replace it;
❒remove the bulb by pushing it slightly
and turning it anticlockwise (bayonet
mount);
❒refit the bulb holder B by turning it
clockwise and making sure that it
locks correctly❒refit the protective rubber cover A fig.
205.
Side
To change the bulb, proceed as
follows fig. 210:
❒move the mirror manually to permit
access to the two fixing screws A;
❒using the Phillips screwdriver
provided, undo the screws
and extract the bulb holder assembly,
releasing it from the teeth;
❒undo the bulb and replace bulb B,
turning it anticlockwise.
FOG LIGHTS
(for versions/markets, where
provided)
To replace the front fog light bulbs,
proceed as follows:
❒steer the wheel completely inwards;
❒undo the screw A and remove the
flap B fig. 211;
❒adjust the catch C fig. 212 and
disconnect the electrical connector
D;
❒turn and remove the bulb holder E;
❒release the bulb and replace it;
❒refit the new bulb and carry out the
procedure described previously in
reverse.
209F1A0317
210F1A0195
213

REAR LIGHT
CLUSTERS
The bulbs are arranged inside the
light cluster as follows fig. 213:
A brake/side lights
B side light
C direction indicators
D reverse lights.
E rear fog lightsTo change the bulb, proceed as
follows fig. 214, fig. 215:
❒open the rear wing door.
❒undo the 7 fixing screws A of the
plastic cover;
❒undo the two fixing screws B;
❒extract the unit outwards and
disconnect the electrical connector;
❒unscrew the screws C using the
screwdriver provided and remove the
bulb holder;
❒remove the bulb D, E, F pushing it
gently and turning it anticlockwise
(“bayonet” locking), then replace
it; remove the bulb G, H pulling
outwards;
❒refit the bulb holder and tighten the
screws C;❒reconnect the electrical connector,
correctly reposition the unit on the
body of the vehicle and then tighten
the fixing screws B;
❒refit the plastic cover fastening it with
the 7 fixing screws A.
211F1A0361
212F1A0362
213F1A0318
214F1A0319
214
IN AN EMERGENCY

For truck and chassis
cab versions:
Undo the four screws H fig. 216
and replace the bulbs:
I bulb for rear fog light
L bulb for reversing light
M bulb for side light
N bulb for brake light
O bulb for side light.THIRD BRAKE LIGHTSTo replace the bulb proceed as
follows:
❒undo the two fixing screws fig. 217;
❒extract the lens unit;
❒press in the tabs B fig. 218 and
remove the bulb holder;
❒remove the snap-fitted bulb and
replace.
NUMBER PLATE
LIGHTS
To replace the bulb proceed as
follows:
❒operate in the point indicated by the
arrow and remove the lens unit A fig.
219;
215F1A0320216F1A0200
217F1A0204
218F1A0205
215

❒change the bulb releasing it from the
side contacts and making sure the
new bulb is correctly fastened
between the contacts;
❒refit the snap-fitted lens unit.
SIDE LIGHTS
(for versions/markets, where
provided)To replace the bulb proceed as
follows:
❒for extra-long van:
– undo the two fixing screws C fig.
220 and remove the light cluster;
– remove the bulb holder D on the
rear of the light cluster, turning it
through a 1/4 turn;
– remove the snap-fitted bulb and
replace.
❒for chassis cabs with platform:
– remove the bulb-holder on the
rear of the light cluster, turning
through 1/4 turn;
– remove the snap-fitted bulb and
replace.
CHANGING AN
INTERIOR BULB
For the type of bulb and relevant
power rating, see paragraph
“Changing a bulb”.
FRONT ROOF LIGHT
Proceed as follows to replace the
bulbs:
❒operate in the point shown by the
arrow and remove roof light A fig.
221;
❒open protective flap B fig. 222;
❒replace the bulbs C fig. 222,
releasing them from the side contacts
and making sure that the new bulbs
are correctly secured between the
contacts;
❒close flap B fig. 222 and fix roof light
A fig. 221 in its housing, making sure
that it locks into place.
REAR ROOF LIGHT
Proceed as follows to replace the
bulbs:
❒operate in the points indicated by the
arrows and remove roof light D fig.
223;
❒open protective flap E fig. 224;
219F1A0206
220F1A0207
216
IN AN EMERGENCY

❒replace bulb F fig. 224, releasing it
from the side contacts and making
sure that the new bulb is correctly
locked between these contacts;
❒close protective flap E fig. 224 and
refit roof light D fig. 223 in its
housing, making sure that it locks
into place.
REPLACING FUSES
GENERAL
INFORMATION
46)
165) 166) 167) 168)
Fuses protect the electrical system:
they intervene (blow) in the event
of a fault or improper action on the
system. When a device does not
work, check the condition of its
fuse: the filament A fig. 225 must
be intact. If it is not, replace the
blown fuse with another having the
same amperage (same colour).
B intact fuse.
C fuse with damaged filament.
221F1A0208
222F1A0209
223F1A0210
224F1A0211
225F1A0212
217

Dashboard fuse box
fig. 226 - fig. 227
DEVICE PROTECTED FUSE AMPERE
Right dipped beam headlight F12 7,5
Left dipped headlight F13 7,5
Engine compartment control unit relay, dashboard control unit relay (+key) F31 5
Lighting of roof lights in the passenger compartment (+battery) F32 7,5
Battery monitoring sensor for Start&Stop versions (+battery) F33 7,5
Minibus interior lights (emergency) F34 7,5
Radio, climate control, alarm, tachograph, battery disconnecting control unit,
Webasto timer (+battery)F36 10
Brake light control (main), third brake light, instrument panel (+key) F37 7,5
Door lock (+battery) F38 20
Windscreen wiper (+key) F43 20
Driver's side electric window F47 20
Passenger side electric window F48 20
Parking sensor control unit, radio, steering wheel controls, central control panel,
left control panel, auxiliary panel, battery disconnecting control unit (+key)F49 5
Climate control, power steering control unit, reverse lights, diesel filter water
sensor, flow meter, tachograph (+key)F51 5
Instrument panel (+battery) F53 7,5
AbsentF89 -
221