2015 Citroen C4 PICASSO instrument panel

145
Before switching off the engine, you can change   to   position   P or N   to   be   in   neutral.  
I

n   either   case,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle,   unless   it   is   programmed  
i

n   automatic   mode.
If the lever is not in position P ,
  on   opening   the  
d

river's   door   or   approximately   45   seconds   after  
s

witching   off   the   ignition   there   is   an   audible  
s

ignal   and   a   message   appears:
F
 
m
ove   the   gear   selector   to   position   P;   the  
a

udible   signal   stops   and   the   message  
d

isappears.
Operating fault
Whenever parking, you must apply the parking brake   to   immobilise   the   vehicle,   if   automatic  
o

peration   has   been   deactivated.
Parking the vehicle
In all circumstances, ensure that the gear   selector   is   in   position   P before
leaving
  your   vehicle. In the event of a fault with the
gearbox,
  the   service   warning   lamp  
c

omes   on   in   the   instrument   panel,  
a

ccompanied   by   a   message   and   an  
a

udible
 s
ignal.
In   this   case   the   gearbox   goes   into   back-up  
m

ode   and   stays   in   3
rd gear. You may then feel a n
oticeable
 
jolt
 
when
 
going   from   P to R   and   from  
N

to R .
 
This
 
jolt
 
does
  not   present   any   risk   to   the  
g

earbox.
Do
 
not
 
exceed
 
60
 
mph   (100   km/h)   while   also  
o

bserving
 
legal
 
speed   limits.
Have
 
it
 
checked
 
by
 
a
  CITROËN   dealer   or   a  
q

ualified
 w

orkshop.
In the event of a battery failure, use the
chock
 
to
 
immobilise
 
the
 
vehicle.
4
Driving

146
Operation
Gear efficiency indicator
System which reduces fuel consumption by recommending the most suitable gear.
T he   system   adapts   its   gear   change  
r

ecommendation   according   to   the  
d

riving   conditions   (slope,   load, ...)   and  
t

he   demands   of   the   driver   (power,  
a

cceleration,   braking, ...).
The
  system   never   suggests:
-
 
e
ngaging   first   gear,
-
 enga

ging
 r
everse
 g
ear,
Example:
The
  information   appears   in   the   instrument  
p

anel   in   the   form   of   an   arrow.
On
  vehicles   with   manual   gearbox,   the   arrow  
c

an   be   accompanied   by   the   recommended  
g

e a r.
Depending
  on   the   driving   situation   and   your  
v

ehicle's   equipment,   the   system   may   advise  
y

ou   to   skip   one   or   more   gears.
You
  can   follow   this   instruction   without   going  
t

hrough   the   intermediate   gears.
The
  gear   engagement   recommendations   must  
n

ot   be   considered   compulsory.
This
  is   because   the   configuration   of   the   road,  
t

raffic   density   and   safety   remain   important  
f

actors   in   the   choice   of   the   best   gear.
The
  gear   efficiency   indicator   system   does   not  
r

eplace   the   need   for   vigilance   on   the   part   of   the  
d

river. -
 
Y
ou   are   in   third   gear.
-
 
Y
ou   press   the   accelerator   pedal.
-
 
T
he   system   may   suggest   that   you   engage  
a

  higher   gear.
With
  an   electronic   or   automatic   gearbox,   the   system   is   only   active   in   manual   mode.
On
  BlueHDi   Diesel   135   and   150   versions   with  
m

anual   gearbox,   in   certain   driving   conditions  
t

he   system   may   suggest   changing   into   neutral  
s

o   that   the   engine   can   go   into   standby   (STOP  
m

ode   with   Stop   &   Start).   In   this   case,   N is
displayed
  in   the   instrument   panel. This
  function   cannot   be   deactivated.
Driving

149
The system is reactivated automatically every   time   the   engine   is   started   by   the  
d

river.
Reactivation
Press this button again.
Operating fault
Have it checked by a CITROËN dealer or a qualified w orkshop.
In
  the   event   of   a   fault   in   STOP   mode,   the   vehicle
 m

ay   stall.
All
  of   the   instrument   panel   warning   lamps   come   on.
Depending
  on   version,   an   alert   message   may   also
 b

e   displayed,   asking   you   to   place   the   gear   selector
 l

ever on position N
 
and   put   your   foot   on   the   brake
 ped

al.
It
  is   then   necessary   to   switch   off   the   ignition   and
 s

tart   the   engine   again   using   the   "START/STOP"
 b

utton. In
 
t
he  
e
vent  
o
f  
a
 
f
ault  
w
ith  
t
he  
s
ystem,  
t

he   symbol   for   the   button   changes  
t

o   alert   mode   and   the   warning   lamp  
f

lashes   for   a   few   moments   then  
c

omes   on   continuously.
The
 
system
 
is
 
active
 
again;
 
this
 
is
 
c

onfirmed
 
by
 
the
 
indicator
 
lamp
 
in
 
the
 b
utton
 
going
 
off
 
and
 
illumination
 
of
 t
his
 
symbol.
The
  Stop   &   Start   system   makes   use   of  
a

dvanced   technology.   For   any   work   on  
t

he   system   go   to   a   qualified   workshop  
w

ith   the   skills   and   equipment   required,  
w

hich   a   CITROËN   dealer   is   able   to  
pro

vide.
Before
  doing   anything   under   the  
b

onnet,   deactivate   the   Stop   &   Start  
s

ystem   to   avoid   any   risk   of   injury  
r

esulting   from   automatic   operation   of  
S

TART   mode.
Maintenance
This system requires a 12 V battery with a special   specification   and   technology   (reference  
n

umbers   available   from   CITROËN   dealers).
Fitting
  a   battery   not   listed   by   CITROËN  
i

ntroduces   the   risk   of   malfunction   of   the  
s

ystem.
For
  charging,   use   a   12   V   charger   and   do   not  
r

everse   the   polarity.
4
Driving

150
Display of inter-vehicle time
Using a radar located at the front of the vehicle, this   system   helps   the   driver   maintain   a   safe  
d

istance   between   their   vehicle   and   the   one   in  
f

ront,   by   displaying   the   current   inter-vehicle  
t

ime   in   the   instrument   panel.
It
  is   the   time   interval,   expressed   in   seconds,  
t

hat   separates   two   vehicles   in   line.   The  
r

ecommended   safe   value   is   about   2   seconds:  
r

efer   to   the   legislation   or   highway   code   in   force  
i

n   your   country.Conditions for display
The measurement is displayed for information   only:   the   system   takes   no a

ction   on   the   vehicle.
This
  system   does   not   in   any
 c

ircumstances   replace   the   need   for
 v

igilance   on   the   part   of   the   driver   who
 m

ust   remain   in   control   of   the   vehicle   at
 a

ll   times.
The
  system   is   not   designed   for   urban
 u

se
 
nor
 
for
 
more
 
dynamic
 
driving
 
(bends,
 a

cceleration,   harsh   braking…)   but   rather
 w

hen   driving   at   a   steady   speed.
The
  system   is   active   in   a   speed   range  
b

etween   42   and   93   mph   (70   and  
1

50 km/h).
Stationary   vehicles   and   certain   other  
r

oad   users   (such   as   bicycles   for  
e

xample)   are   not   detected.
The   system   displays   inter-vehicle   time  
v

alues   of   between   3   seconds   and   0.5   of  
a

  second.
Below   0.5   of   a   second,   the   value  
d

isplayed   is   maintained   at   this   level,  
e

ven   if   the   true   inter-vehicle   time   is   less.
The   active   cruise   control   must   not  
b

e   selected   (the   active   cruise   control  
i

nformation   is   displayed   instead   of   that  
f

or   the   inter-vehicle   time).
The   system   is   only   available   with   the  
"

DRIVING"   display   mode   of   the  
type   2   instrument   panel.
Driving

151
Once the speed conditions are met, a symbol is displayed in the instrument panel.
Displays
SymbolAssociated message Comments
No
  vehicle   detected   by   the   radar.
A
  vehicle   is   detected   but   the   inter-vehicle   time   is   more   than   3   seconds.   No   value   is  
d

isplayed.
A
  vehicle   is   detected.   The   inter-vehicle   time   is   3   seconds   or   less.   The   minimum   value  
d

isplayed   is   0.5   seconds,   even   if   the   true   inter-vehicle   time   is   lower.
4
Driving

155
Steering mounted controls
6. Speed  limiter   on   /   pause   indication.
7. S peed   limiter   mode   selection   indication.
8.
 S

peed   value   setting.
Speed limiter "LIMIT"
System which prevents the vehicle from exceeding the speed programmed by the driver.
T he   speed   limiter   cannot,   in   any
 c

ircumstances,   replace   the   need   to
 o

bserve   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.
Once
  the   programmed   speed   limit   is   reached,  
a

dditional   pressure   on   the   accelerator   pedal  
h

as   no   effect.
1.
 S

elect   speed   limiter   mode.
2.
 D

ecrease
 p
rogrammed
 s
peed.
3.
 I

ncrease   programmed   speed.
4.
 S

peed   limiter   on   /   pause.
5.
 D

isplay   the   list   of   memorised   speeds.
Displays in the instrument panel
Switching on  the   speed   limiter   requires  a
  programmed   speed   of   at   least   20   mph  
(

30 km/h).
The
  speed   limiter   is   paused by operation of the
control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly  
b

eyond   the   point   of   resistance.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal   until   the   vehicle  
r

eturns   to   the   programmed   speed   limit.
The
  programmed   speed   remains   in   the
 m

emory   when   the   ignition   is   switched   off.For
  more   information   on   the   list   of   memorised  
s

peeds,   refer   to   the   "Memorising   speeds"  
s

ection.
4
Driving

158
Steering mounted controls
6. Cruise  control   pause   /   resume   indication.
7. C ruise   control   mode   selection   indication.
8.
 S

peed   value   setting.
Cruise control "CRUISE"
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
The cruise control system cannot, in any circumstances, replace the need to observe speed limits, nor can it replace the need for vigilance on the part of the driver.
Y ou   are   advised   to   keep   your   feet   near   the   pedals   at   all   times.
Switching on the cruise control requires a
minimum   vehicle   speed   of   25   mph   (40   km/h).
As
  well   as   engagement   of:
-
 
f
ourth   gear   or   higher   on   a   manual   gearbox,
-
 
s
econd   gear   or   higher   in   manual   mode   on  
a

n   electronic   or   automatic   gearbox,
-
 
p
osition   A   on   an   electronic   gearbox   or   D on
an
  automatic   gearbox.
The cruise control is paused
 

manually   or  
b

y   pressing   the   brake   or   clutch   pedal   or  
o

n   triggering   of   the   ESP   system   for   safety  
r

easons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal   until   the  
p

rogrammed   cruise   speed   is   reached   again.1.
 S

elect   cruise   control   mode.
2.


a
c
tivate the cruise control at the current
speed
  of   the   vehicle,   then   decrease the
programmed
 s

peed.
3.


a
c
tivate the cruise control at the current
speed
  of   the   vehicle,   then   increase the
programmed
 s

peed.
4.
 P

ause   /   resume   cruise   control.
5.
 D

isplay   the   list   of   memorised   speeds.Displays in the instrument panel
Switching off the ignition cancels any programmed   speed   value. For
  more   information   on   the   list   of   memorised  s
peeds,   refer   to   "Memorising   speeds"   section.
Driving

164
In the event of the presence of a
vehicle  detected   by   the   radar,   if   the  
s

peed   selected   is   much   higher   than  
t

he   speed   of   that   vehicle,   the   system  
i

s   not   activated   and   the   alert   message  
"

Activation   not   possible,   conditions  
u

nsuitable"   is   displayed   until   driving  
c

onditions   are   safe   to   allow   activation   of  
t

he   system.
Exceeding the speed setting
The information is grouped together in the instrument pan el.
6.
 I

ndication   of   cruise   control   pause/resume.
7.
 I

ndication   of   selection   of   cruise   control  
m

ode,   or
 v

ehicle   speed   adjustment   phase.
8.
 C

ruise   speed   setting,   or
 a

djusted   speed   lower   than   the   cruise  
se

tting.
Displays in the instrument panel
Modification of the cruise control
speed and/or the inter-vehicle
time
Button 5 (MEM)
Press button 5 ,   the   six   memorised   speeds   and  t
he   inter-vehicle   time   setting   are   displayed   in  
t

he   touch   screen   tablet.
F
 
C
hoose   a   speed   setting:   it   is   displayed   in  
t

he   instrument   panel,
F

p
ress or the " +" or " -" button to choose
a
  new   inter-vehicle   time   setting   between  
2

.5 seconds   and   1   second.
This
  speed   value   remains   memorised,  
w

hatever   the   state   of   the   system.
The selection screen closes after a few
moments.
 

The
 
modifications
 
are
 
then
 
accepted.
If the active cruise control has not been
switched
  on,   pressing   button   5   (MEM)  
h

as   no   effect. It
  is   possible   to   exceed   the   speed   setting  
t

emporarily   by   depressing   the   accelerator  
ped

al.
Then
  simply   release   the   accelerator   pedal   to  
r

eturn   to   the   programmed   speed.
If
  the   speed   setting   is   unintentionally   exceeded,  
d

escending   a   steep   hill   for   example,   the   speed  
s

etting   in   the   instrument   panel   flashes   as   a  
w

arning.
driving