2015 Citroen C4 lock

167
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Switching off the engine
F Immobilise  the   vehicle.
F  P lace   the   gear   selector   lever   at   N for
vehicles
  with   an   electronic   gearbox,   P or N
with
  an   automatic   gearbox,   or   neutral   with  
a m

anual
 g
earbox.
do n

ot leave your vehicle with the
electronic
  key   still   inside.
Switching
  off   the   engine   leads   to   a   loss  
o

f   braking   assistance.
If
  the   vehicle   is   not   immobilised,   the  
e

ngine   will   not   stop.
F
 
W
ith   the   electronic   key   inside  
t

he vehicle, press the " S TA R T/
STOP "
  button.
 T

he   engine   stops   and   the  
s

teering   column   locks.
Emergency starting
When the electronic key is in the recognition zone   and,   after   pressing   the   "START/STOP"
button,
  the   engine   does   not   start:
F
 
P
lace   the   gear   selector   at   N for vehicles
with
  an   electronic   gearbox,   P or N for
vehicles
  with   an   automatic   gearbox   or  
n

eutral   for   vehicles   with   a   manual   gearbox.F
 P lace   the   electronic   key   in   the   back-up  
re

ader.
 (

see   the   "Access   -   Back-up   key"   section).
F
 
P
ress   the   brake   pedal   on   vehicles   with   an  
e

lectronic   or   automatic   gearbox,   or   fully  
d

eclutch   with   a   manual   gearbox.
F

P
ress the "START/STOP"
button.
 T

he   engine   starts.
9
Driving

168
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Emergency switch-off
In the event of an emergency only, the  e ngine  c an  b e  s witched  o f  w ithout  
c

onditions.   To   do   this,   press   and   hold  
t

he "START/STOP" button for about
3
  seconds.
In
 
this
 
case   the   steering   column   locks   as   soon  
a

s
 
the
 
vehicle   stops.
Electronic key not
recognised
If the electronic key is no longer in the recognition   zone   when   driving   or   when   you  
(

later)   request   switching   off   the   engine,   a  
m

essage   is   displayed.
F

P
ress and hold the " S TA R T/
STOP" button for about
3 seconds
  if   you   want   to   force  
s

witching   off   the   engine   (note
that restar ting will not be
possible without the key ).
Ignition on position
(without starting)
With the Keyless Entry and Starting key inside t
he   vehicle,   pressing   the   "   START/STOP "
button, with no action on the pedals , allows
the
  ignition   to   be   switched   on.
With
  the   ignition   on,   the   system  
a

utomatically   goes   into   energy  
e

conomy   mode   when   required   to  
m

aintain   the   state   of   charge   of   the  
b

attery.F

P
ress the "START/STOP"
button,
  the   instrument   panel  
c

omes   on   but   the   engine   does  
n

ot   start.
F
 
P
ress   the   button   again   to   switch   off   the  
i

gnition   and   so   allow   the   vehicle   to   be  
lo

cked.
Driving

169
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
anti-theft protection
Electronic engine immobiliser
Keep safely, away from your vehicle, the   label   attached   to   the   keys   given   to  
y

ou   on   acquisition   of   the   vehicle.
The
 
keys
 
contain
 
an
 
electronic
 
chip
 
which
 
has
 a
 
special
 
code.
 
When
 
the
 
ignition
 
is
 
switched
 
o

n,
 
this
 
code
 
must
 
be
 
recognised
 
for
 
engine
 
s

tarting
 
to
 
be
 
authorised.
This
 
electronic
 
engine
 
immobiliser
 
locks
 
the
 
e

ngine
 
management
 
system
 
a
 
few
 
minutes
 
a

fter
 
the
 
ignition
 
is
 
switched
 
off
 
and
 
prevents
 
s

tarting
 
of
 
the
 
engine
 
by
 
anyone
 
who
 
does
 
not
 
h

ave
 
the
 
key. In the event of a fault, you are
informed
 
by
 
illumination
 
of
 
this
 
w

arning
 
lamp,
 
an
 
audible
 
signal
 
a

nd/or
 
the
 
display
 
of
 
a
 
message,
 
d

epending
 o

n
 v

ersion.
In
 
this
 
case,
 
your
 
vehicle
 
will
 
not
 
start;
 
contact
 
a

 
CITROËN
 
dealer
 
as
 
soon
 
as
 
possible.
9
driving

187
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
When the ignition is on, the lighting   of   this   warning   lamp,  
a

ccompanied   by   an   audible   signal  
a

nd   a   message   in   the   multifunction  
s

creen,   indicates   a   gearbox  
m

alfunction.
Operating fault
You risk damaging the gearbox:
- i f you press the accelerator and
brake
  pedals   at   the   same   time,
-
 
i
f  
y
ou  
f
orce  
t
he  
l
ever  
f
rom  
p
osition P
to another position when the
battery
  is   flat.
To
  reduce   fuel   consumption   when  
s

tationary   for   long   periods   with   the  
e

ngine   running   (traffic   jam...),   position  
t

he   gear   lever   at   N and apply the
parking
  brake,   unless   it   is   programmed  
i

n   automatic   mode.
In
 
this
 
case,
 
the
 
gearbox
 
switches
 
to
 
back-up
 
m

ode
 
and
 
is
 
locked
 
in
 
3rd
 
gear.
 
You
 
may
 
feel
 
a

 
substantial
 
knock
 
when
 
changing
 
from
 
P
to R
 
and
 
from
 
N to R .
 
This
 
will
 
not
 
cause
 
any
 
d

amage
 
to
 
the
 
gearbox.
Do
 
not
 
exceed
 
60
 
mph
 
(100
 
km/h),
 
local
 
speed
 
r

estrictions
 p

ermitting.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
This
 
warning
 
lamp
 
may
 
also
 
come
 
on
 
if
 
a
 
door
 
i

s
 ope

ned.
9
Driving

217
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
Screenwash / headlamp
wash fluid level
Specification of the fluid
To ensure optimum cleaning and to avoid freezing,   the   fluid   should   never   be   topped   up   or r

eplaced   by   plain   water.
In wintry conditions, the use of a fluid
with
  an   ethyl   alcohol   or   methanol   base   is  
re

commended.
To
 
check
 
the
 
level
 
or
 
top
 
up
 
the
 
f

luid
 
on
 
vehicle
 
fitted
 
with
 
headlamp
 
w

ashers,
 
immobilise
 
the
 
vehicle
 
and
 
s

witch
 
of
 
the
 
engine.
F
o
p

en the bonnet and secure it with the
st ay.
F
 
O

pen
 
the
 
screenwash
 
reservoir
 
filler
 
cap.
F
 
T

ake
 
and
 
pinch
 
the
 
level
 
gauge
 
to
 
block
 
its
 
b

reather.
F
 
R

emove
 
the
 
gauge
 
completely
 
from
 
t

he reservoir to read the level in the
transparent
 s

ection.
Coolant level
The coolant level should be close
to   the   "MA X"   mark   but   should   never  
e

xceed   it.
Fluid specification
The coolant must conform to the manufacturer's r ecommendations.
The cooling fan may star t after
switching off the engine: take care
with articles and clothing that might
be caught by the fan blades.
When
  the   engine   is   warm,   the   temperature   of  
t

he   coolant   is   regulated   by   the   fan.
In   addition,   as   the   cooling   system   is  
p

ressurised, wait at least one hour after
switching   off   the   engine   before   carrying   out  
any   work.
To   avoid   any   risk   of   scalding,   unscrew   the   cap  
b

y   two   turns   to   allow   the   pressure   to   drop.  
W

hen   the   pressure   has   dropped,   remove   the  
c

ap   and   top   up   the   level. F  
T
op   up   if   necessary.
F
R
efit the filler cap to the reservoir and
close   the   bonnet.
10
Checks

219
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
Checks
Particle filter (Diesel)
- fixed  illumination   of   the   particle  f
ilter   warning   lamp,   accompanied  
b

y   an   audible   signal   and   a  
m

essage   that   there   is   a   risk   of  
b

lockage   of   the   particle   filter.
The presence of this label, in particular with
the
 
Stop
 
&
 
Start
 
system,
 
indicates
 
the
 
use
 
of
 
a s

pecific 12 V lead-acid battery with special
technology
 
and
 
specification.
 
The
 
involvement
 
o

f
 
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified
 
workshop
 
i

s
 
essential
 
when
 
replacing
 
or
 
disconnecting
 
t

he
 
battery. As
 
soon
 
as   the   traffic   conditions   permit,  
r

egenerate   the   filter   by   driving   at   a   speed   of   at  
l

east
 
40
 
mph   (60   km/h)   until   the   warning   lamp  
g

oes
 
off.
If
 
the
 
warning   lamp   stays   on,   refer   to   the  
"

Additive
 
level"   section.
Unless
 
other wise
 
indicated,
 
check
 
these
 
components
 
in
 
accordance
 
with
 
the
 
manufacturer's
 
service
 
schedule
 
and   according   to   your   engine.
Other wise,
 
have
 
them
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified
 
workshop.
Air filter and passenger compartment filter
Refer to the manufacturer's s
ervice schedule for details of the
replacement
  intervals   for   these  
c

omponents.
Oil filter
Replace the oil filter each time the e ngine   oil   is   changed.
Refer
  to   the   manufacturer's  
s

ervice schedule for details of
the
  replacement   interval   for   this  
c

omponent.
12 V battery
The battery does not require any maintenance.
H owever,   check   that   the   terminals   are   clean a

nd   correctly   tightened,   particularly   in   summer
 a

nd   winter.
When carrying out work on the battery, refer to the "12 V battery" section for details of the
precautions
  to   be   taken   before   disconnecting  
t

he   battery   and   following   its   reconnection.Depending
  on   the   environment   (e.g.   dusty  a
tmosphere)   and   the   use   of   the   vehicle  
(e.g.
  city   driving),   replace them twice as often
if necessary .
A
  clogged   passenger   compartment   filter   may  
h

ave   an   adverse   effect   on   the   per formance  
o

f   the   air   conditioning   system   and   generate  
u

ndesirable
 o
dours.The start of saturation of the particle filter is
indicated
  by:
on a n

ew vehicle, the first operations of
regeneration
  of   the   particle   filter   may   be  
a

ccompanied   by   the   smell   of   "burning",  
w

hich   is   per fectly   normal.
Following
  prolonged   operation   of   the  
v

ehicle at very low speed or at idle,
you
  may,   in   exceptional   circumstances,  
n

otice   the   emission   of   water   vapour   at  
t

he   exhaust   on   acceleration.   This   does  
n

ot affect the behaviour of the vehicle
or
  the   environment.
10
Checks

227
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
Recommendations on storage Procedure
F Switch  off   the   ignition   and   remove   the  k
ey,   or   if   your   vehicle   has   one,   press   the  
S

TART/STOP   button   to   switch   off   the  
e

ngine. F

R
aise the boot floor for access to the
a

d
blu
e
® tank. S
ecure
 
the   boot   floor   by   attaching   its   cord  
t

o
 
the
 
hook   on   the   parcel   shelf   support.
F
 
U

nclip
 
the   black   plastic   blanking   plug   using  
i

ts
 
tab.
F
 
I

nsert
 
your   fingers   into   the   aperture   and  
t

urn
 
the
 
blue   cap   a   6
th of a turn anti-
clockwise.
F
 
C

arefully
 
lift
 
off
 
the
 
cap,   without   dropping   it.
ne

ver store bottles of
a
dbl

ue
® in your
vehicle. Before
  topping-up,   ensure   that   the   vehicle   is  
p

arked   on   a   flat   and   level   sur face.
In wintry conditions, ensure that the
temperature   of   the   vehicle   is   above   -11°C.  
O

ther wise,   by   freezing,   the   AdBlue
® cannot
be
 
poured
 
into
 
its
 
tank.
 
Park
 
your
 
vehicle   in   a  
w

armer
 
area
 
for
 
a
 
few
 
hours
 
to
 
allow   the   top-up  
t

o
 
be
 
carried
 
out.
a

d
blu

e
® freezes at about -11°C and d
eteriorates   above   25°C.   It   is   recommended  
t

hat bottles be stored in a cool area and
protected
  from   direct   sunlight.
Under
 
these   conditions,   the   additive   can   be  
k

ept
 
for
 
at   least   a   year.
If the additive has frozen, can be used once it
has
 
completely   thawed   out.
10
Checks

228
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
F obtain a bottle of adbl ue®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank. F  
A
fter   emptying   the   bottle,   wipe   away   any  
s

pillage   around   the   tank   filler   using   a   damp  
c

loth.
F  
R
efit   the   blue   cap   to   the   tank   and   turn   it  
a
  6
th of a turn clockwise, to its stop.
F
 R
efit   the   black   plastic   blanking   plug,  
c

lipping   it   in   on   the   flap
F
 
D

etach   the   cord   from   the   parcel   shelf  
s

upport   and   lower   the   boot   floor.
Important:
 
if
 
your
 
vehicle's
 
AdBlue®
tank
 
is
 
completely
 
empty
 
-
 
which
 
is
 
c

onfirmed
 
by
 
the
 
alert
 
displays
 
and
  the  
i

mpossibility
 
of
 
starting
 
the
 
engine
 
-  
you
 
must
 
add
 
at
 
least
 
3.8 litres
 

(so
 
two
 
1.89
 
litre
 
bottles). If any additive is split or splashed, wash
immediately
 
w
ith  
c
old  
w
ater  
o
r  
w
ipe  
w
ith  
a

  damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up
after a breakdown because of a lack
of additive ,   you   must   wait   around  
5   minutes   before   switching   on   the  
ig

nition,
 w
ithout opening the
driver's door, locking the vehicle,
introducing the key into the ignition
switch, or introducing the key of the
"Keyless Entr y and Star ting" system
into the passenger compartment .
Switch   on   the   ignition,   then,   after  
10   seconds,   start   the   engine.
ne

ver dispose of a
dbl
ue
® additive
bottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 p

urpose
 o

r
 t

ake
 t

hem
 t
o
 y
our
 d
ealer.
Checks