2015 Citroen C4 remove seats

11
C4-2_en_Chap00c_eco-conduite_ed01-2015
C4-2_en_Chap00c_eco-conduite_ed01-2015
Limit the causes of excess consumption
Spread loads throughout the vehicle; place the heaviest items in the bottom   of   the   boot,   as   close   as   possible   to   the   rear   seats.
Limit
  the   loads   carried   in   the   vehicle   and   reduce   wind   resistance   (roof  
b

ars,   roof   rack,   bicycle   carrier,   trailer...).   Use   a   roof   box   in   preference.
Remove
  roof   bars   and   roof   racks   after   use.
At
  the   end   of   winter,   remove   snow   tyres   and   refit   your   summer   tyres.
Observe the recommendations on maintenance
Check the tyre pressures regularly, when cold, referring to the label in the   door   aperture,   driver's   side.
Carry
  out   this   check   in   particular:
-
 
b
efore   a   long   journey,
-
 
a
t   each   change   of   season,
-
 
a
fter   a   long   period   out   of   use.
Don't
  forget   the   spare   wheel   and   the   tyres   on   any   trailer   or   caravan.
Have
  your   vehicle   serviced   regularly   (engine   oil,   oil   filter,   air   filter,  
p

assenger   compartment   filter...)   and   observe   the   schedule   of  
o

perations   recommended   in   the   manufacturer's   service   schedule.
With
  a   BlueHDi   Diesel   engine,   if   the   SCR   system   is   faulty   your   vehicle  
b

ecomes   polluting;   go   to   a   CITROËN   dealer   or   a   qualified   workshop  
w

ithout   delay   to   have   the   emissions   of   nitrous   oxides   brought   back   to  
t

he   legal   level.
When
  refuelling,   do   not   continue   after   the   third   cut-off   of   the   nozzle   to  
a

void   any   over flow.
At
  the   wheel   of   your   new   vehicle,   it   is   only   after   the   first   1   800   miles  
(

3 000   kilometres)   that   you   will   see   the   fuel   consumption   settle   down   to  
a

  consistent   average.
.
Eco-driving

93
C4-2_en_Chap04_confort_ed01-2015
C4-2_en_Chap04_confort_ed01-2015
Additional adjustments
Head restraint height and angle
F To  raise   a   head   restraint,   pull   it   upwards.
F  T o   lower   the   head   restraint,   press   the   lug   A
and
  the   head   restraint   at   the   same   time.
F
 
T
o   adjust   the   angle   of   the   head   restraint,   tilt  
i

ts   lower   part   for wards   or   rear wards.
Heated seats control
With the engine running, the front seats can be heated s eparately.
F
 
U
se   the   adjustment   dial,   placed   on   the   side  
o

f each front seat, to switch on and select
the
  level   of   heating   required:
0: O

f f.
1:

 
L
ow.
2:

  Medium.
3:

 
Hig
h.
Removing a head restraint
F To  remove   the   head   restraint,   press   the  l
ug A   and   pull   the   head   restraint   upwards.
F
 
T
o   put   the   head   restraint   back   in   place,  
e

ngage   the   head   restraint   stems   in   the  
o

penings   keeping   them   in   line   with   the   seat  
b

ack   and   press   the   lug   A   at   the   same   time.
The
 
head
 
restraint
 
is
 
fitted
 
with
 
a
 
frame
 
w

ith
 
notches
 
which
 
prevents
 
it
 
from
 
l

owering;
 
this
 
is
 
a
 
safety
 
device
 
in
 
case
 
o

f
 
impact.
The adjustment is correct when the
upper edge of the head restraint is
level with the top of the head.
ne

ver drive with the head restraints
removed;
  they   must   be   in   place   and  
adj

usted
 c
orrectly.
4
Comfort

96
C4-2_en_Chap04_confort_ed01-2015
C4-2_en_Chap04_confort_ed01-2015
Rear seats
Rear head restraints
These have one position for use (up) and a stowed   position   (down).
They
  can   also   be   removed.
To
  remove   a   head   restraint:
F
 
r
elease   the   backrest   using   control   1,
F
 
t
ilt   the   backrest   2   slightly   for wards,
F

p
ull the head restraint upwards to the stop,
F
 
t
hen,   press   the   lug   A. F
 
M
ove   the   corresponding   front   seat   for ward  
i

f   necessary.
F

P
osition the seat belt between the outer
and centre head restraints to avoid
trapping
  the   belt   when   repositioning   the  
s

eat   backrest.
F

P
lace the head restraints in the low
position. F

P
ull control 1 for wards to release the seat
back
  2.
F
 
F
old   the   seat   back   2   on   to   the   cushion.
ne

ver drive with the head restraints
removed;
  they   must   be   in   place   and  
c

orrectly
 adj
usted.
Folding the backrest
Bench seat with fixed one-piece cushion and split backrest (left hand 2/3, right hand 1/3) which can be   folded   individually   to   adapt   the   load   space   in   the   boot.
Comfort

114
C4-2_en_Chap05_amenagement_ed01-2015
C4-2_en_Chap05_amenagement_ed01-2015
To remove the shelf:
F  u nhook   the   two   cords,
F
 
r
aise   the   shelf   slightly,   then   remove   it.
There
  are   several   options   for   storing   the   shelf:
-
 
e
ither   upright   behind   the   front   seats,
-
 
o
r   flat   at   the   base   of   the   boot.
Rear parcel shelf
The hooks can be used to secure shopping bags.
Hooks
Access to the storage box
An additional hook under the shelf is u sed   to   hold   up   the   boot   floor   using   its  
c

ord, to facilitate access to the tools
and
  spare   wheel   or   the   temporary  
p

uncture   repair   kit...
Fittings

143
C4-2_en_Chap07_securite-enfants_ed01-2015
C4-2_en_Chap07_securite-enfants_ed01-2015
(a)  Universal  child   seat:   child   seat   which   can   be  i
nstalled   in   all   vehicles   using   the   seat   belt.
(b)
  
G
roup   0:   from   birth   to   10 kg.   Infant   car   seats  
a

nd "car cots" cannot be installed on the
front
 p

assenger
 sea
t.
(c)
  
C
onsult   the   legislation   in   force   in   your  
c

ountry   before   installing   your   child   on   this  
sea

t.
(d)
  
T
o   install   a   child   seat   at   the   rear,   rear ward  
o

r   for ward   facing,   move   the   front   seat  
f

or ward,   then   straighten   the   backrest   to  
a

llow   enough   room   for   the   child   seat   and   the  
c

hild's   legs. U:
  s eating   position   suitable   for   the   installation  o
f   a   child   seat   secured   using   the   seat   belt  
a

nd   universally   approved   rear ward   facing  
a

nd/or   for ward   facing.
U(R1) :

i
dentical to U,
  with   the   vehicle's   seat  
b

ackrest   inclined   fully   for wards.
U(R2) :

i
dentical to U,
  with   the   vehicle's   seat  
a

djusted   to   the   highest   position.
X:
  s

eating   position   not   suitable   for   installing   a  
c

hild   seat   for   the   weight   group   indicated.Remove
  and   stow   the   head   restraint  
b

efore   installing   a   child   seat   with  
b

ackrest   on   a   passenger   seat.   Refit   the  
h

ead restraint once the child seat has
been
  removed.
7
Child safety

144
C4-2_en_Chap07_securite-enfants_ed01-2015
C4-2_en_Chap07_securite-enfants_ed01-2015
"ISOFIX" mountings
There are three rings for each seat:
-  
t
wo   rings   A, located between the vehicle
seat
  back   and   cushion,   indicated   by   a  
m

arking, This
  ISOFIX   mounting   system   provides   fast,  
r

eliable   and   safe   fitting   of   the   child   seat   in   your  
v

ehicle.
The ISOFIX child seats are fitted with two
latches
  which   are   secured   on   the   two   rings   A.
Some
  seats   also   have   an   upper strap, which is
attached
  to   ring   B.
Your vehicle has been approved in accordance with the latest
IS
oFI
X regulation
.
The   seats,   represented   below,   are   fitted   with   regulation   ISOFIX   mountings:
To secure the child seat to the TOP TETHER :
-  
r
emove   and   stow   the   head   restraint   before  
i

nstalling   the   child   seat   on   the   seat   (refit   it  
o

nce   the   child   seat   has   been   removed),
-
r
aise the carpet cover on the T
oP
T
ETHER,
-
p
ass the upper strap of the child seat
behind   the   seat   backrest,   between   the  a
pertures for the head restraint rods,
-  f ix   the   hook   of   the   upper   strap   to   the   ring   B,
-
 
t
ighten   the   upper   strap.
-
 
a
  ring   B, behind the seat and identified by
a
  marking,   referred   to   as   the   TOP TETHER
for
  fixing   the   upper   strap.
The incorrect installation of a child seat
in
  a   vehicle   compromises   the   child's  
p

rotection   in   the   event   of   an   accident.
Follow
  strictly   the   fitting   instructions  
p

rovided   by   with   the   child   seat.
When
  fitting   an   ISOFIX   child   seat   to  
t

he   left   hand   rear   seat,   before   fitting   the  
s

eat,   first   move   the   centre   rear   seat   belt  
t

owards   the   middle   of   the   vehicle,   so  
a

s   to   avoid   the   seat   inter fering   with   the  
o

peration   of   the   seat   belt.
For
  information   on   the   possibilities   for  
i

nstalling   ISOFIX   child   seats   in   your  
v

ehicle,   refer   to   the   summary   table.
Child safety

147
C4-2_en_Chap07_securite-enfants_ed01-2015
C4-2_en_Chap07_securite-enfants_ed01-2015
* Infant car seats and "car cots" cannot be installed on the front passenger seat.
* *   The   ISOFIX   infant   car   seat,   secured   on   the   lower   rings   of   a   vehicle   ISOFIX   seat,   occupies   two   rear   seats.
Locations for ISoFIX child seatsIn accordance with European Regulations, this table indicates the options for installing ISOFIX child seats on seats in the vehicle fitted with ISOFIX m
ountings.
In
  the   case   of   universal   and   semi-universal   ISOFIX   child   seats,   the   ISOFIX   size   category,   determined   by   a   letter   from   A to G , is indicated on the child seat
next
  to   the   ISOFIX   logo.
I UF:

s
eat suitable for the installation of an I sofix
  Universal seat, " For ward
  facing"   secured   using   the  
u

pper   strap.
IL- SU: seat suitable for the installation of an I sofix
  Semi- Universal
 sea

t
 ei
ther:
-
 
r
ear ward   facing   fitted   with   an   upper   strap   or   a   support   leg,
-
 
f
or ward   facing   fitted   with   a   support   leg,
-
 
a
n   infant   car   seat   fitted   with   an   upper   strap   or   a   support   leg.
For
  advice   on   securing   of   the   upper   strap,   refer   to   the   "ISOFIX   mountings"   section.Weight of the child
/indicative
  age
Less than 10
kg
(group 0)
Up
  to   approx.  
6

  monthsLess than 10 kg
(group 0)
Less than 13 kg (group 0+)
Up
  to   approx.   1   yearFrom 9 to 18 kg (group 1)
From
  approx.   1   to   3   years
Type of ISOFIX child seat Infant car seat*rearward facing rearward facing forward facing
ISOFIX size categor y F G C D E C D A B B1
ISOFIX child seats universal and
semi-universal which can be installed
on the rear outer seats IL- SU
** IL- SU IL- SU IUF
IL- SU
Remove
  and   stow   the   head   restraint  
b

efore   installing   a   child   seat   with   a  
b

ackrest   on   a   passenger   seat.   Refit   the  
h

ead restraint once the child seat has
been
  removed.
7
Child safety

148
C4-2_en_Chap07_securite-enfants_ed01-2015
C4-2_en_Chap07_securite-enfants_ed01-2015
For optimum installation of the for ward facing child   seat,   ensure   that   the   back   of   the   child  
s

eat   is   as   close   as   possible   to   the   backrest   of  
t

he   vehicle's   seat,   in   contact   if   possible.
You
  mst   remove   the   head   restraint   before  
i

nstalling   a   child   seat   with   backrest   to   a  
p

assenger
 sea
t.
Ensure that the head restraint is stored or
attached
  securely   to   prevent   it   from   being  
t

hrown around the vehicle in the event of
sharp
  braking.   Refit   the   head   restraint   when  
t

he   child   seat   is   removed.
advice on child seats
Installing a booster
seat
Children at the frontThe incorrect installation of a child seat in a
vehicle   compromises   the   child's   protection   in  
t

he   event   of   an   accident.
Ensure that there is no seat belt or seat belt
buckle
  under   the   child   seat,   as   this   could  
de

stabilise
 i
t.
Remember
  to   fasten   the   seat   belts   or   the  
c

hild   seat   harnesses   keeping   the   slack  
r

elative   to   the   child's   body   to   a   minimum,  
e

ven   for   short   journeys.
When
  installing   a   child   seat   using   the   seat  
b

elt,   ensure   that   the   seat   belt   is   tightened  
c

orrectly on the child seat and that it secures
the
  child   seat   firmly   on   the   seat   of   your  
v

ehicle.   If   your   passenger   seat   is   adjustable,  
m

ove   it   for wards   if   necessary. The
  legislation   on   carrying   children   on   the  
f

ront   passenger   seat   is   specific   to   each  
c

ountry.   Refer   to   the   legislation   in   force   in  
y

our   country.
Deactivate
  the   passenger   airbag   when   a  
r

ear ward   facing   child   seat   is   installed   on   the  
f

ront   seat.
Other wise,
  the   child   would   risk   being  
s

eriously   injured   or   killed   if   the   airbag   were  
t

o   inflate.The
  chest   part   of   the   seat   belt   must   be  
p

ositioned   on   the   child's   shoulder   without  
t

ouching   the   neck.
Ensure that the lap part of the seat belt
passes
  correctly   over   the   child's   thighs.
CITROËN
  recommends   the   use   of   a   booster  
s

eat   which   has   a   back,   fitted   with   a   seat   belt  
g

uide   at   shoulder   level.
As
  a   safety   precaution,   do   not   leave:
-

a c
hild or children alone and
unsupervised in a vehicle,
-
 
a
  child   or   an   animal   in   a   vehicle   which  
i

s   exposed   to   the   sun,   with   the   windows  
c

losed,
-
 
t
he   keys   within   reach   of   children   inside  
t

he   vehicle.
At
  rear   seating   positions,   always   leave  
s

ufficient   space   between   the   front   seat   and:
-
 
a
  rear ward   facing   child   seat,
-
 
t
he   child's   feet   for   a   child   seat   fitted  
fo

rward
 f
acing.
To
  do   this,   move   the   front   seat   for wards  
a

nd,   if   necessary,   move   its   backrest   into   the  
u

pright
 p
osition. To
  prevent   accidental   opening   of   the   doors  
a

nd   rear   windows,   use   the   child   lock.
Take
  care   not   to   open   the   rear   windows   by  
m

ore   than   one   third.
To
  protect   young   children   from   the   rays   of   the  
s

un,   fit   side   blinds   on   the   rear   windows.
Child safety