2015 Citroen C4 brake

191
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
The flashing and then fixed illumination   of   the   under-inflation w

arning   lamp   accompanied   by   the
 i

llumination   of   the   service   warning
 l

amp   indicates   a   fault   with   the   system.
Operating fault
The aler t  is  given  by  the  fixed  illumination o
f   this   warning   lamp,   accompanied   by a

n   audible   signal,   and   depending   on
 e

quipment,   the   display   of   a   message.
Under-inflation alert
In the event of a problem on one of the tyres, the   symbol   or   the   message   appears,   according  
t

o   equipment,   to   identify   it.
F
 
R
educe   speed,   avoid   sudden   steering  
m

ovements   or   harsh   brake   applications.
F
 
S
top   as   soon   as   it   is   safe   to   do   so. In
  this   case,   monitoring   of   the   tyre   pressures   is  
n

ot   assured.
F  
I
f   you   have   a   compressor   (the   one   in   the  
t

emporary   puncture   repair   kit   for   example),  
c

heck   the   four   tyre   pressures   when   cold.
 I

f   it   is   not   possible   to   check   the   tyre  
p

ressures   at   the   time,   drive   carefully   at  
r

educed
 s
peed.


or
F
I
n the event of a puncture, use the
temporary   puncture   repair   kit   or   the   spare  
w

heel   (according   to   equipment).
Go   to   a   CITROËN   dealer   or   a   qualified  w
orkshop to   have   the   system   checked   or,  
f

ollowing   the   repair   of   a   puncture,   to   have   the  
o

riginal   wheel,   equipped   with   a   sensor,   refitted.
Any
  tyre   repair   or   replacement   on   a   wheel  
f

itted   with   this   system   must   be   carried   out   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
If
  after   changing   a   tyre,   a   wheel   is   not   detected  
b

y   your   vehicle   (fitting   snow   tyres   for   example),  
y

ou   must   have   the   system   reinitialised   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
The loss of pressure detected does not
always
  lead   to   visible   deformation   of   the  
t

yre.   Do   not   rely   on   just   a   visual   check.This alert is also displayed when one or
more
  wheels   is   not   fitted   with   a   sensor  
(

for   example,   a   space-saver   or   steel  
spar

e
 w
heel).
The   alert   is   maintained   until   the   tyre   or  t
yres concerned is reinflated, repaired
or
  replaced.
The
  spare   wheel   (space-saver   type   or   a  
s

teel   rim)   does   not   have   a   sensor.
9
Driving

192
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Stop & Start
Operation
Going into engine STOP mode
The "ECO"  warning   lamp   comes   on i
n   the   instrument   panel   and   the   engine g

oes   into   standby   automatically:
-

w

ith a manual gearbox , at speeds below
12
 
m

ph  
(
20  
k
m/h),  
o
r  
v
ehicle  
s
tationary  
w
ith  
P

ureTech   130   petrol   and   BlueHDi   Diesel  
v

ersions,   when   you   put   the   gear   lever   into  
n

eutral and release the clutch pedal,
If your vehicle is fitted with the
system,
  a   time   counter   calculates
 t

he   sum   of   the   periods   in   STOP
 m

ode   during   a   journey.   It   resets
 i

tself   to   zero   every   time   the
 i

gnition   is   switched   on   with   the
 k

ey   or   the   "START/STOP"   button.
-

w

ith an electronic gearbox , at a speed
below
  5   mph   (8   km/h),   when   you   press  
t

he
 
brake   pedal   or   put   the   gear   lever   into  
p

osition N .
Special cases: STOP mode
unavailable
STOP mode is not invoked when:
-  t he   vehicle   is   on   a   steep   slope   (up   or  
d

ow n),
-
 
t
he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   (using  
t

he   key   or   the   "   START/STOP"   button),
-
 
t
he   electric   parking   brake   is   applied   or  
be

ing
 a
pplied,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case, the "ECO"
 

warning   lamp  
f

lashes for a few seconds, then
goes
  off.
This operation is perfectly normal.
The
 
Stop
 
&
 
Start system
 
puts
 
the
 
engine
 
temporarily
 
into
 
standby
 
-
 
STOP
 
mode
 
-
 
during
 
stops
 
in
 
the
 
traffic   (red   lights,   traffic   jams,   or   other...).  
The
 
engine
 
restarts
 
automatically
 
-
 
START
 
mode
 
-
 
as
 
soon
 
as
 
you
 
want
 
to
 
move
 
off.
 
The
 
restart
 
takes
 
place   instantly,   quickly   and   silently.
Per fect
 
for
 
urban
 
use,
 
the
 
Stop
 
&
 
Start
 
system
 
reduces
 
fuel
 
consumption
 
and
 
exhaust
 
emissions
 
as
 
well
  as   the   noise   level   when   stationary.
Never
 
refuel
 
with
 
the
 
engine
 
in
 
STOP
 
m

ode;
 
you
 
must
 
switch
 
off
 
the
 
ignition
 
w

ith
 
the
 
key
 
or
 
the
 
"START/STOP"
 
b

utton.
With
 
an
 
electronic
 
gearbox,
 
for
 
your
 
c

omfort
 
during
 
parking
 
manoeuvres,
 
S

TOP
 
mode
 
is
 
not
 
available
 
for
 
a
 
few
 
s

econds
 
after
 
coming
 
out
 
of
 
reverse
 
g

e a r.
STOP
 
mode
 
does
 
not
 
affect
 
the
 
f

unctionality of the vehicle, such as
braking,
 
power
 
steering,
 
for
 
example.
driving

193
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Deactivation
Going into engine START mode
At any time, press the "ECO OFF" switch to
d eactivate   the   system.
This
  is   confirmed   by   the   switch   warning   lamp  
c

oming   on   accompanied   by   the   display   of   a  
m

essage.
Special cases: START invoked
automatically
The "ECO"  warning   lamp   goes   off  a
nd   the   engine   starts   automatically:
-

w

ith a manual gearbox , when you fully
depress the clutch pedal,
-

w

ith an electronic gearbox :
●
 
g

ear   lever   in   position   A or M, when you
release
  the   brake   pedal,
●
 
o

r
 
gear   lever   in   position   N   and   the   brake  
p

edal   released,   when   you   move   the   gear  
l

ever to position A or M ,
●
 
o

r
 
when   you   engage   reverse   gear.For
  safety   reasons   or   to   ensure   smooth  o
peration,   START   mode   is   invoked  
a

utomatically
 w
hen:
-
 
y
ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   15 mph  
(

25   km/h)   with   a   manual   gearbox   (3 km/h  
(

2   mph)   with   PureTech   130   petrol   and  
B

lueHDi   Diesel   versions)   or   7   mph  
(

11 km/h)   with   an   electronic   gearbox,
-
 
t
he   electric   parking   brake   is   being   applied,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case the "ECO"
 

warning   lamp  
f

lashes for few seconds, then
goes
  off.
This operation is perfectly normal.
With
  a   manual   gearbox   in   STOP   mode,  
i

f
 
a
  gear   is   engaged   without   fully  
d

epressing   the   clutch   pedal,   a   warning  
l

amp   comes   on   or   an   alert   message  
i

s
 
displayed   asking   you   to   depress   the  
c

lutch   pedal   to   restart   the   engine. If
  the   system   has   been   deactivated  
i

n   STOP   mode,   the   engine   restarts  
i

mmediately.
9
Driving

194
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Maintenance
In the event of a malfunction with the system, the "ECO OFF"   switch   warning   lamp   flashes,  
t

hen   comes   on   continuously.
Ha

ve   it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating fault
This system requires a specific battery with a special   specification   and   technology   (reference  
n

umbers   available   from   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop).
Fitting
  a   battery   not   listed   by  
C

ITROËN introduces   the   risk   of   malfunction   of  
t

he   system.Before
  doing   anything   under   the  
b

onnet, deactivate the Stop & Start
system   to   avoid   any   risk   of   injury  
r

esulting   from   automatic   operation   of  
S

TART   mode.
The   Stop   &   Start   system   makes   use  
o

f   advanced   technology.   All   work   on  
t

his   type   of   battery   must   be   done   only  
b

y   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 
mode,
 
the
 v

ehicle
 
may
 
stall.
 
All
 
of
 
the
 
instrument
 p

anel
 
warning
 
lamps
 
come
 
on.
Depending
 
on
 
version,
 
an
 
alert
 
m

essage
 
may
 
also
 
be
 
displayed
 
asking
 
y

ou
 
to
 
put
 
the
 
gear
 
lever
 
into
 
position
 
N
and
 
put
 
your
 
foot
 
on
 
the
 
brake
 
pedal.
It is then necessary to switch off the
ignition,
 
then
 
restart
 
the
 
engine
 
using
 
t

he
 
key
 
or
 
the
 
"START/STOP"
 
button.
Reactivation
The system is reactivated automatically a t   every   new   start   using   the   key   or   the  
"

START/STOP"   button.
Press the "ECO OFF"
  switch   again.
The
 
system   is   active   again;   this   is   confirmed  
b

y
 
the
  switch   warning   lamp   going   off   and   the  
d

isplay   of   a   message.
Driving

203
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Cruise control
The functions of this system are grouped together   on   the   steering   mounted   controls.
1.
 C

ruise   control   mode   selection   dial.
2.
 S

peed   programming   /   value   decrease  
b

utton.
3.
 S

peed   programming   /   value   increase  
b

utton.
4.
 C

ruise   control   off   /   resume   button.
5.
 M

emorised   speeds   display   button.
Steering mounted controls
The programmed information is grouped together   in   the   instrument   panel   screen.
6.
  C

ruise   control   off   /   resume   indication.
7.
  C

ruise   control   mode   selection   indication.
8.
  P

rogrammed   speed   value.
9.
  S

electing   a   stored   speed.
Displays in the instrument panel
The cruise control is switched on m anually: it r
equires   a   minimum   vehicle   speed   of   25   mph  
(

40   km/h)   and   engagement   of:
-
 
f
ourth   gear   on   the   manual   gearbox,
-
 
s
econd   gear   on   the   electronic   gearbox  
s

ystem   or   automatic   gearbox,   in   sequential  
d

riving   mode,
-
position A
  on   the   electronic   gearbox  
s

ystem   or   D   on   an   automatic   gearbox.
The cruise control is switched off
 m

anually
 o

r   by   pressing   the   brake   or   clutch   pedal   or   on  
t

riggering   of   the   trajectory   control   systems,   for  
s

afety   reasons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal.
Switching
  off   the   ignition   cancels   any  
p

rogrammed   speed   value.
The cruise control system cannot, in any circumstances, replace   the   need   to   observe   speed   limits,   nor   can   it r

eplace   the   need   for   vigilance   on   the   part   of   the   driver.
You
  are   advised   to   keep   your   feet   near   the   pedals   at
 a

ll   times.
System which automatically maintains the speed of the vehicle at the value programmed by the driver,   without   any   action   on   the   accelerator   pedal.
Operation
9
driving

216
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
Topping up the engine oil level
Refer to the "Petrol engine" or "Diesel engine" section for the location of the oil filler cap in the
engine
  compartment   of   your   vehicle.
F
 
U
nscrew   the   oil   filler   cap   to   reveal   the   filler  
a

perture.
F
 
A
dd   oil   in   small   quantities,   avoiding   any  
s

pills   on   engine   components   (risk   of   fire).
F
 
W
ait   a   few   minutes   before   checking   the  
l

evel   again   using   the   dipstick.
F
 
A
dd   more   oil   if   necessary.
F
 
A
fter   checking   the   level,   carefully   refit   the  
o

il   filler   cap   and   the   dipstick   in   its   tube.
After
  topping   up   the   oil,   the   check   when  
s

witching   on   the   ignition   with   the   oil   level  
i

ndicator   in   the   instrument   panel   is   not   valid  
d

uring   the   30   minutes   after   topping   up.
Engine oil change
Refer to the manufacturer's service schedule for   details   of   the   interval   for   this   operation.
In
  order   to   maintain   the   reliability   of   the   engine  
a

nd   emission   control   system,   never   use  
a

dditives   in   the   engine   oil.
Brake fluid level
Changing the fluid
Refer to the manufacturer's service schedule for   details   of   the   interval   for   this   operation.
Fluid specification
The brake fluid must conform to the manufacturer's r ecommendations.
The
  brake   fluid   level   should   be   close  
t

o   the   "MA X"   mark.   If   it   is   not,   check  
t

he   brake   pad   wear.
Power steering
fluid level
The power steering fluid level should b
e   close   to   the   "MA X"   mark.   With   the e

ngine   cold,   unscrew   the   cap   to   check
 t

he   level.
Checks

220
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
Automatic
gearbox
The gearbox does not require any maintenance   (no   oil   change).
Refer
  to   the   manufacturer's  
s

ervice schedule for details of
the
  level   checking   interval   for   this  
c

omponent.
Electric parking
brake
This system does not require any routine   servicing.   However,   in  
t

he   event   of   a   problem,   have   the  
s

ystem   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
Manual parking
brake
If a loss of effectiveness of this
system
 i s  n oticed,  t he  p arking  b rake  
m

ust   be   checked,   even   between  
t

wo   services.
Brake pads
Brake wear depends on the style of   driving,   particularly   in   the   case  
o

f vehicles used in town, over short
distances.
  It   may   be   necessary   to  
Brake disc
wear
For information on checking brake disc wear, contact a CITRoËn
dealer
  or   a   qualified   workshop.For
  more   information,   refer   to   the   "Electric
 p

arking   brake   -   Operating   faults"   section.
Manual gearbox
The gearbox does not require any m
aintenance   (no   oil   change).
Refer
  to   the   manufacturer's   service  
s

chedule   for   the   checking   interval  
f

or   this   component.
Electronic gearbox
The gearbox does not require any maintenance   (no   oil   change).
Refer
  to   the   manufacturer's   service  
s

chedule   for   details   of   the   checking  
i

nterval   for   this   component. Only
  use   products   recommended   by  
C

ITROËN   or   products   of   equivalent  
q

uality
 an
d
 sp
ecification.
In
  order   to   optimise   the   operation   of  
u

nits   as   important   as   those   in   the  
b

raking   system,   CITROËN   selects   and  
o

ffers   very   specific   products.
After
  washing   the   vehicle,   dampness,  
o

r   in   wintry   conditions,   ice   can   form  
o

n   the   brake   discs   and   pads:   braking  
e

fficiency   may   be   reduced.   Make   light  
b

rake   applications   to   dry   and   defrost  
t

he   brakes.
have
  the   condition   of   the   brakes   checked,   even  
b

etween
 v
ehicle
 s
ervices.
Unless   there   is   a   leak   in   the   circuit,   a   drop   in  
t

he   brake   fluid   level   indicates   that   the   brake  
p

ads   are   worn.
Checking   this   system   must   be   done   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
Checks

235
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
For BlueHDi Diesel versions
If your vehicle has an electric parking brake,
the   jack   is   stowed   in   a   bag   placed   in   the   bottom  
o

f   the   boot. If your vehicle has a manual parking brake
,
the   jack   is   stowed   under   the   spare   wheel   and  
u

nder   the   storage   box:
F
 
r
emove   the   spare   wheel,
F
 
r
emove   the   polystyrene   storage   box,
F
 
p
ush   the   jack   for ward,   then   lift   it   by   its   rear  
par

t.The spare wheel is installed in the boot under
the
  floor.
Depending
  on   version,   the   spare   wheel   may   be  
a 

standard
 
size
 
steel
 
or
 
alloy
 
wheel,
 
or
 
for
 
some
 c

ountries   it   is   the   "space   saver"   type.
For access to the spare wheel, refer to the
paragraph
  "Access   to   the   tools"   on   the   previous  
pag

e.
Access to the spare wheel
If your vehicle has an electric parking brake,   only   a   "space   saver"   type   of  
w

heel   can   be   stowed   in   the   boot.
11
Practical information