2015 Citroen C4 brake

237
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Removing a wheel
* position R   for   an   electronic   gearbox;   P for an
automatic   gearbox.
List of operations
F Remove   the   chromed   bolt   cover   from   each  o
f   the   bolts   using   the   tool   3   (according   to  
e

quipment).
F
 
F
it   the   security   socket   4 on the
wheelbrace


1   to   slacken   the   security   bolt.
F
 
S
lacken   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
Parking the vehicle
Immobilise the vehicle where it does not block   traffic:   the   ground   must   be   level,  
s

table   and   non-slippery   ground.
Apply
  the   parking   brake   unless   it   has  
b

een   programmed   to   automatic   mode,  
s

witch   off   the   ignition   and   engage   first  
g

ear*   to   lock   the   wheels.
Check
  that   the   braking   warning   lamps  
i

n   the   instrument   panel   are   on   (not  
f

lashing).
The
  occupants   must   get   out   of   the  
v

ehicle   and   wait   where   they   are   safe.
If
  necessary,   place   a   chock   under   the  
w

heel   diagonally   opposite   the   wheel   to  
be c

hanged.
Never
  go   underneath   a   vehicle   raised  
u

sing   a   jack;   use   an   axle   stand.
11
Practical information

241
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Snow chains
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when braking.
Advice on installation
F If   you   have   to   fit   the   chains   during   a  j
ourney,   stop   the   vehicle   on   a   flat   sur face  
o

n   the   side   of   the   road.
F
 
A
pply   the   parking   brake   and   position   any  
w

heel   chocks   to   prevent   movement   of   your  
v

ehicle.
F
 
F
it   the   chains   following   the   instructions  
p

rovided   by   the   manufacturer.
F
 
M
ove   off   gently   and   drive   for   a   few  
m

oments,   without   exceeding   30 mph  
(

50 km/h).
F
 
S
top   your   vehicle   and   check   that   the   snow  
c

hains   are   correctly   tightened.
Use
 
only
 
the
 
chains
 
designed
 
to
 
be
 
fitted
 
to
 
the
 t
ype
 
of
 
wheel
 
fitted
 
to
 
your
 
vehicle:
Original
 
tyre
 
size Maximum
 
link
 
size.
195/65
 
R15 9
 
mm
205/55
 
R16
225/45
 
R17
225/40
 
R18
cannot be fitted with chains
For more information on snow chains, contact a C ITROËN   dealer   or   a   qualified   workshop.
It
  is   strongly   recommended   that   before  
y

ou   leave,   you   practise   fitting   the   snow  
c

hains   on   a   level   and   dry   sur face.
The
 
snow
 
chains
 
must
 
be
 
fitted
 
only
 
t

o
 
the
 
front
 
wheels.
 
They
 
must
 
never
 
b

e fitted to "space-saver" type spare
wheels.
Take  account   of   the   legislation   in   force  
i

n your country on the use of snow
chains
  and   the   maximum   running   speed  
a

uthorised. Avoid
  driving   with   snow   chains   on   roads  
t

hat have been cleared of snow, to
avoid
  damaging   your   vehicle's   tyres   and  
t

he   road   sur face.   If   your   vehicle   is   fitted  
w

ith   alloy   wheels,   check   that   no   part   of  
t

he   chain   or   its   fixings   is   in   contact   with  
t

he   wheel   rim.
11
Practical information

248
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Model with 3D rear lamps
1. Brake lamp (P21W).
2. Sidelamp (R10W ).
3.
D

irection indicator (PY21W amber) .
4.
R

ear foglamp, offside (P21W).
5.
R

eversing lamp, nearside (P21W).
Access to rear lamps
Amber bulbs, such as those for the direction   indicators,   must   be   replaced  
b

y   bulbs   of   the   same   rating   and   colour.
The
  lamps   on   the   tailgate   are   dummy  
u

nits.   They   are   there   for   aesthetic  
p

urposes   only.
Rear lamps
Model with conventional lamps
(t y p e 1)
1. Brake lamp / sidelamp (P21/5W).
2. Direction indicator (PY21W amber) .
3.
R

eversing lamp (P21W).
4.
R

ear foglamp (P21W). You
  will   need   a   flat   screwdriver   and   a   10   mm  
b

ox
 span
ner.
The
  four   bulbs   are   changed   from   inside   the  
b

oot:
F

o
pen the boot,
F
 
r
emove   the   access   flap   from   the  
c

orresponding   side   trim   panel,
F
 
u
nclip   the   lamp   unit   connector,
F
 
a
s   a   precaution,   place   a   cloth   in   the   bottom  
o

f   the   housing   to   catch   the   nut   if   it   is  
d

ropped   on   removal,
F
 
s
lacken   the   hexagonal   nut   using   a   10   mm  
b

ox   spanner   then   remove   the   nut   by   hand,
F
 
c
arefully   remove   the   lamp   unit   by   pulling  
o

ut   it   straight   out   towards   the   rear.
Practical information

250
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
To facilitate the removal of the lamp, carry out this   operation   with   the   tailgate   half   open.
F

I
nsert a thin screwdriver into the lens
cutout.
F
 
P
ush   it   outwards.
F
 
R
emove   the   lens.
F
 
C
hange   the   faulty   bulb.
To
  refit,   press   on   the   lens   to   clip   it   in   place.
Third brake lamp (LEDs)
For the replacement of this type of light emitting diode   lamp,   contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Number plate lamps (W5W)
Practical information

263
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Towing the vehicle
The towing eye is installed in the boot under the   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F

r
aise the floor,
F
 
s
ecure   it   by   hooking   its   cord   on   the   hook  
o

n the rear parcel shelf
s
upport,
F
 
r
emove   the   towing   eye   from   the   holder.
Access to the tools General recommendations
In the following cases, you must always call o
n   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or  
f

ast road,
-
f

our-wheel drive vehicle,
-

w
hen it is not possible to put the
gearbox
  into   neutral,   unlock   the  
 
s

teering,   or   release   the   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the  
g

round,
-
 
w
here   there   is   no   approved   towing   arm  
a

vailable...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed
 
or
 
for
 
towing
 
another
 
vehicle
 
using
 
a
 
removable
 
towing
 
ey

e.
Observe
 
the
 
legislation
 
in
 
force
 
in
 
your
 c
o unt r y.
Ensure
 
that
 
the
 
weight
 
of
 
the
 
towing
 
vehicle
 
i

s
 
higher
 
than
 
that
 
of
 
the
 
towed
 
vehicle.
The
 
driver
 
must
 
remain
 
at
 
the
 
wheel
 
of
 
the
 
t

owed
 
vehicle
 
and
 
must
 
have
 
a
 
valid
 
driving
 
l

icence.
When
 
towing
 
a
 
vehicle
 
with
 
all
 
four
 
wheels
 
o

n
 
the
 
ground,
 
always
 
use
 
an
 
approved
 
t

owing
 
arm;
 
rope
 
and
 
straps
 
are
 
prohibited.
The
 
towing
 
vehicle
 
must
 
move
 
off
 
gently.
When
 
towing
 
a
 
vehicle
 
with
 
the
 
engine
 
off,
 
t

here
 
is
 
no
 
longer
 
any
 
power
 
assistance
 
for
 
b

raking
 
or
 
steering.
11
Practical information

266
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
F If  the   warning   lamp   and   the  S
TOP  warning   lamp   come   on,  
s

top the vehicle and switch off
the
  engine   as   soon   as   possible.
Braking
Towing a trailer increases the braking distance.
T o   avoid   overheating   of   the   brakes   on   a   long  
m

ountain   type   of   descent,   the   use   of   engine  
b

raking   is   recommended.
Ty r e s
F Check   the   tyre   pressures   of   the  
towing   vehicle   and   of   the   trailer,   observing  
t

he
 re
commended
 p
ressures.
Lighting
F Check  the   electrical   lighting   and   signalling  o
n   the   trailer.
The
  rear   parking   sensors   will   be  
d

eactivated   automatically   if   a   genuine  
C

ITROËN   towbar   is   used.
Cooling
Towing a trailer on a slope increases the temperature   of   the   coolant.
As
  the   fan   is   electrically   controlled,   its   cooling  
c

apacity   is   not   dependent   on   the   engine   speed.
F
 
T
o   lower   the   engine   speed,   reduce   your  
s

peed.
The
  maximum   towed   load   on   a   long   incline  
d

epends   on   the   gradient   and   the   ambient  
t

emperature.
In
  all   cases,   keep   a   check   on   the   
c
oolant  
t

emperature.
Practical information

277
C4-2_en_Chap12_caracteristique_ed01-2015
C4-2_en_Chap12_caracteristique_ed01-2015
* The kerb weight is equal to the unladen weight + driver (75 kg).
* *   T he   weight   of   the   braked   trailer   can   be   increased,   within   the   GTW   limit,   if   the   GV W   of   the   towing   vehicle   is   reduced   by   an   equal   amount.  
Warning:
  towing   using   a   lightly   loaded   towing   vehicle   may   have   an   adverse   effect   on   its   road   holding.
Petrol weights and towed loads (in kg)
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each   additional   1   000   metres   of   altitude.
When
  towing,   the   maximum   authorised   speed   is   reduced   (comply   with   the   legislation   in   force   in   your   country).
High
  ambient   temperatures   may   result   in   a   reduction   in   the   per formance   of   the   vehicle   to   protect   the   engine;   if   the   ambient   temperature   is   above   37   °C,  
l

imit   the   towed   load.
Petrol engine
VTi 95Puretech 110 V Ti 120
Gearbox Manual

(5 - speed) Manual

(5 - speed) Manual

(5 - speed) Automatic

(4 - speed)
Model code:
NC... 8FR0HNZ6
HNZ6/1 -/2 5FS05FS9

5FS9/D
-  
U
nladen   weight
1 2001 200 1 205 1   270
-  
K
erb   weight*
1   275
1   275
1   280
1   345
-  
G
ross   vehicle   weight   (GV W)
1   720
1   770
1   765
1   755
-  
G
ross   train   weight   (GTW)  

o
n   a   12   %   gradient
2   920
2   970
3   065
3   055
-  
B
raked   trailer   (within   the   GTW   limit)  

o
n   a   12   %   gradient
1 200
1 2001   300
1   300
-  
B
raked   trailer**   (with   load   transfer   within   the  
G

TW   limit)
1 450
1 4501 550 1 550
-  
U
nbraked   trailer
635635640 670
-  
R
ecommended   nose   weight
75757575
12
Technical data

278
C4-2_en_Chap12_caracteristique_ed01-2015
C4-2_en_Chap12_caracteristique_ed01-2015
* The kerb weight is equal to the unladen weight  + driver (75 kg).
* *   T he   weight   of   the   braked   trailer   can   be   increased,   within   the   GTW   limit,   if   the   GV W   of   the   towing   vehicle   is   reduced   by   an   equal   amount.  
Warning:
  towing   using   a   lightly   loaded   towing   vehicle   may   have   an   adverse   effect   on   its   road   holding.
The
  GTW   and   towed   load   values   indicated   are   valid   up   to   a   maximum   altitude   of   1   000   metres;   the   towed   load   mentioned   must   be   reduced   by   10   %   for  
e

ach   additional   1   000   metres   of   altitude.
When
  towing,   the   maximum   authorised   speed   is   reduced   (comply   with   the   legislation   in   force   in   your   country).
High
  ambient   temperatures   may   result   in   a   reduction   in   the   per formance   of   the   vehicle   to   protect   the   engine;   if   the   ambient   temperature   is   above   37   °C,  
l

imit   the   towed   load.
Petrol engine
Puretech 130 S&S THP 155
Gearbox Manual

(6- speed) EAT6 Automatic
(6- speed) ETG6 Electronic

(6- speed)
Model code:
NC... HNYM/S
HNYM/1S HNY T/S
HNY T/1S - /2S 5FV8/P
-  
U
nladen   weight
1 2051 240 1   275
-  
K
erb   weight*
1   280
1   315
1   350
-  
G
ross   vehicle   weight   (GV W
1   790
1   810
1   805
-  
G
ross   train   weight   (GTW)  
 
o
n   a   12%   gradient
3   090
3   110
3   205
-  
B
raked   trailer   (within   the   GTW   limit)  
 
o
n   a   12%   gradient
1   300
1   300
1 400
-  
B
raked   trailer**   (with   load   transfer   within  
t

he GTW   limit)
1 550
1 550 1   650
-  
U
nbraked   trailer
640655 675
-  
R
ecommended   nose   weight
757575
Technical data