2015 Citroen C4 wheel

164
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Starting the engine
F With  a   petrol   engine,   operate   the   starter  m
otor   by   turning   the   key   to   position   3
without
  pressing   the   accelerator   pedal,  
u

ntil   the   engine   starts.   Once   the   engine   is  
r

unning,   release   the   key. F
 
W
ith   a   Diesel   engine,   turn   the   key   to  
p

osition 2
,   ignition   on,   to   operate   the  
eng

ine
 p
re-heating
 s
ystem.
Wait   until   this   warning   lamp   goes   off  
i

n   the   instrument   panel   then   operate  
t

he   starter   motor   by   turning   the   key  
t

o position 3   without   pressing   the  
a

ccelerator   pedal,   until   the   engine  
s

tarts.   Once   the   engine   is   running,  
r

elease   the   key.
If   the   engine   does   not   start   straight  
a

way,   switch   off   the   ignition.   Wait   a  
f

ew   moments   before   operating   the  
s

tarter   motor   again.   If   the   engine   does  
n

ot   start   after   several   attempts,   do   not  
k

eep   trying:   you   risk   damaging   the  
s

tarter   motor   or   the   engine.   Contact  
a

  CITROËN   dealer   or   a   qualified  
w

orkshop.Never
  leave   the   engine   running   in  
a

n   enclosed   area   without   adequate  
v

entilation:
 in
ternal
 c
ombustion
 e

ngines   emit   toxic   exhaust   gases,  
s

uch   as   carbon   monoxide.   Danger   of  
i

ntoxication   and   death.
In very severe wintry conditions
(temperatures   below   -23°C),   to   ensure  
t

he correct operation and durability of
the   mechanical   components   of   your  
v

ehicle,   engine   and   gearbox,   it   is  n
ecessary   to   leave   the   engine   running  f
or   4   minutes   before   moving   off.
In
  certain   cases,   you   may   have   to   apply  
m

ore   force   to   the   steering   (wheels   on  
f

ull   lock,   for   example).
In   wintry   conditions,   the   warning   lamp  
c

an   stay   on   for   a   longer   period.   When  
t

he   engine   is   hot,   the   warning   lamp  
d

oes   not   come   on.In   temperate   conditions,   do   not   leave  
t

he   engine   at   idle   to   warm   up   but   move  
o

ff   straight   away   and   drive   at   moderate  
s

peed.
With   the   parking   brake   applied   and   the   gearbox  
i

n neutral or position N or P
:
F  
d
epress   the   clutch   pedal   fully   (manual  
g

earbox),


or
F  
p
ress   the   brake   pedal   firmly   (electronic   or  
a

utomatic   gearbox),
F  
i
nsert   the   key   into   the   ignition   switch;   the  
s

ystem   recognises   the   code,
F  
u
nlock   the   steering   column   by  
s

imultaneously   turning   the   steering   and   the  
k

ey.
Driving

166
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Starting-switching off the engine with the 
" Keyless   Entry   and   Starting"   system
Starting the engine
F Place  the   gear   selector   lever   at   N for
vehicles   with   an   electronic   gearbox,   P or N
with
  an   automatic   gearbox,   or   neutral   with  
a m

anual
 g
earbox.
F
 
W
ith   the   electronic   key   inside   the   vehicle  
(

it   is   not   necessary   to   put   it   in   the   reader),  
p

ress   the   brake   pedal   for   vehicles   with  
a

n   electronic   or   automatic   gearbox,   or  
f

ully   declutch   for   vehicles   with   a   manual  
g

earbox. F
b
r
iefly press the "
START/STOP"
button.
 T
he   steering   column   unlocks  
a

nd   the   engine   starts   more   or  
l

ess   instantly   (see   the   advice   for  
D

iesel
 v
ersions).
If   this   warning   lamp   comes   on   after  
p

ressing   "START/STOP",   you   should  
h

old   the   brake   or   clutch   pedal   down  
u

ntil   the   warning   lamp   goes   off   and  
d

o   not   press   the   START/STOP   button  
ag

ain.
If
  one   of   the   starting   conditions   is   not
 m
et,   a   reminder   message   appears   in t
he   instrument   panel   screen.   In   some c

ircumstances,   it   is   necessary   to   turn
 t

he   steering   wheel   slightly   while   pressing
 t

he   "START/STOP"   button   to   assist
 u

nlocking   of   the   steering;   a   message
 w

arns   you   when   this   is   needed.If
  the   electronic   key   is   not   detected   in  
t

he   zone,   a   message   is   displayed.   Move  
t

he   electronic   key   into   the   zone   so   that  
t

he   engine   can   be   started.
The presence of the "
ke
yless Entry and
Starting"
  system   electronic   key   in   the  
r

ecognition   zone   is   essential.
For safety reasons, do not leave this
zone
  with   the   vehicle   running.For Diesel vehicles
, in
temperatures   below   zero   the  e
ngine   will   not   start   until   the  
p

reheater   warning   lamp   has  
g

one   off.
driving

171
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
With the vehicle stationary, to apply the parking brake   whether   the   engine   is   running   or   off,   pull
control lever A .
The
  application   of   the   parking   brake   is  
c

onfirmed   by:
-
 i

llumination
 o
f
 t
he
 b
raking
 w
arning
 l

amp   and   of   the   P
 
warning   lamp   in
 t

he control lever A ,
-
 
d
isplay   of   the   message   "Parking  
b

rake   on".
When
  the   driver’s   door   is   opened   with   the  
e

ngine   running,   a   message   is   displayed  
a

ccompanied   by   an   audible   signal   if   the   parking  
b

rake   has   not   been   applied,   except   in   the   case  
o

f   an   automatic   gearbox   with   the   gear   lever   in  
p

osition P .
Before
  leaving   the   vehicle,   ensure
 t

hat   parking   brake   warning   lamp   in   the
 i

nstrument   panel   is   on   fixed,   not   flashing.
Manual applicationManual release
The full application of the parking brake is c
onfirmed   by:
-
 
t
he   braking   warning   lamp   and  
t

he P   warning   lamp   in   the   control  
l

ever A   going   off,
-
 
d
isplay   of   the   message   "Parking  
b

rake   off ".
If you pull control lever A  without   pressing t
he   brake   pedal,   the   parking   brake   will n

ot   be   released   and   a   warning   lamp   will
 c

ome   on   in   the   instrument   panel.
With the ignition on or the engine running, to release   the   parking   brake,   press on the brake
pedal or the accelerator, pull then release
control A . If
  necessary,   you   can   make   a   maximum
application
 
of   the   parking   brake.   This   is  
o

btained
 by m
eans
 o
f
 a long
pull
on the control
lever A ,   until   you   see   the   message   "Parking  
b

rake   on   maximum"   and   a   beep   is   heard.
In   the   case   of   towing,   a   loaded   vehicle   or  
p

arking   on   a   gradient,   make   a   maximum  
a

pplication   of   the   parking   brake   then   turn   the  
f

ront   wheels   towards   the   pavement   and   engage  
a

  gear   when   you   park.
After
  a   maximum   application,   the   release   time  
w

ill   be   longer.
Maximum application
Maximum application is essential:
- i n   the   case   of   a   vehicle   towing   a   caravan  
o

r   a   trailer,   if   the   automatic   functions   are  
a

ctivated   but   you   are   applying   the   parking  
b

rake
 m
anually,
-
 
w
hen   the   gradient   you   are   parked   on   may  
v

ary   (e.g.   on   a   ferry,   on   a   lorry,   during  
tow

ing).
9
Driving

176
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
SituationsConsequences
To   apply   the   electric   parking   brake:
F
 
i
mmobilise   the   vehicle   and   switch   off   the   ignition.
F
 
p
ull   the   control   for   at   least   5   seconds   or   until   application   is   complete.
F
 
s
witch   on   the   ignition   and   check   the   switching   on   of   the   electric   parking  
b

rake   warning   lamps.
The
  application   is   slower   than   during   normal   operation.
To
  release   the   electric   parking   brake:
F
 
s
witch   on   the   ignition.
F
 
p
ull   the   control   and   hold   it   for   approximately   3   seconds   then   release   it.
If
  the   braking   warning   lamp   is   flashing   or   if   the   warning   lamps   do   not   come  
o

n   with   the   ignition   on,   these   procedures   will   not   work.   Place   the   vehicle  
o

n   level   ground   and   have   it   checked   by   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
and possibly
flashing
Display
 
of
 
the
 
message
 
" Parking brake fault "
  and   of   the   following  
w

arning
 lam

ps: -
 
O
nly   the   automatic   application   on   switching   off   the   engine   and   automatic  
r

elease   on   acceleration   functions   are   available.
-
 
T
he   manual   application/release   of   the   electric   parking   brake   and   the  
e

mergency   braking   are   not   available.
and possibly
flashing
Battery
 
fault: -
 I

f   the   battery   warning   lamp   comes   on   you   must   stop   immediately   as   soon   as
 t

he   traffic   allows.   Stop   and   immobilise   your   vehicle   (if   necessary,   place   the
 t

wo   chocks   under   the   wheels).
-
 
A
pply   the   electric   parking   brake   before   switching   off   the   engine.
Driving

177
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Manual parking brake
Applying
F Pull  the   parking   brake   lever   fully   up   to  i
mmobilise   your   vehicle.
Releasing
F Pull  the   parking   brake   lever   up   gently,  p
ress the release button then lower the
lever
 f

ully.
When the vehicle is being driven, if this warning   lamp   and   the   STOP w arning lam p c

ome   on,   accompanied   by   an   audible
 s

ignal   and   a   message   in   the   multifunction
 s

creen,   this   indicates   that   the   parking   brake
 i

s   still   on   or   has   not   been   properly   released.
When parking on a slope, direct your wheels   against   the   kerb,
apply
  the   parking   brake,   engage   a   gear  
a

nd   switch   off   the   ignition.
9
Driving

190
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Tyre under-inflation detection
System which automatically checks the p
ressures   of   the   tyres   while   driving.
The
  system   continuously   monitors   the  
p

ressures of the four tyres, as soon as the
vehicle
  is   moving.
a

pressure sensor is located in the valve of
each
  tyre   (except   the   spare   wheel).
The
  system   triggers   an   alert   if   a   drop   in  
p

ressure   is   detected   in   one   or   more   tyres.
The
  tyre   under-inflation   detection   system   is   an  
a

id   to   driving   which   does   not   replace   the   need  
f

or   vigilance   on   the   part   of   the   driver.This
  system   does   not   avoid   the   need  
t

o   check   the   tyre   pressures   regularly  
(

including   the   spare   wheel)   and   before  
a

  long   journey.
Driving   with   under-inflated   tyres  
a

dversely   affects   road   holding,  
e

xtends   braking   distances   and   causes  
p

remature   tyre   wear,   particularly   under  a
rduous   conditions   (vehicle   loaded,  h
igh   speed,   long   journey).The tyre pressures for your vehicle can
be
  found   on   the   tyre   pressure   label   (see  
t

he   "Identification   markings"   section).
The   tyre   pressures   must   be   checked  
w

hen   the   tyres   cold   (vehicle   stopped  
f

or   1   hour   or   after   driving   for   less   then  
6

  miles   (10   km)   at   moderate   speed).  
O

ther wise,   add   0.3   bar   to   the   values  i
ndicated   on   the   label.
Driving   with   under-inflated   tyres  
i

ncreases   fuel   consumption.
driving

191
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
The flashing and then fixed illumination   of   the   under-inflation w

arning   lamp   accompanied   by   the
 i

llumination   of   the   service   warning
 l

amp   indicates   a   fault   with   the   system.
Operating fault
The aler t  is  given  by  the  fixed  illumination o
f   this   warning   lamp,   accompanied   by a

n   audible   signal,   and   depending   on
 e

quipment,   the   display   of   a   message.
Under-inflation alert
In the event of a problem on one of the tyres, the   symbol   or   the   message   appears,   according  
t

o   equipment,   to   identify   it.
F
 
R
educe   speed,   avoid   sudden   steering  
m

ovements   or   harsh   brake   applications.
F
 
S
top   as   soon   as   it   is   safe   to   do   so. In
  this   case,   monitoring   of   the   tyre   pressures   is  
n

ot   assured.
F  
I
f   you   have   a   compressor   (the   one   in   the  
t

emporary   puncture   repair   kit   for   example),  
c

heck   the   four   tyre   pressures   when   cold.
 I

f   it   is   not   possible   to   check   the   tyre  
p

ressures   at   the   time,   drive   carefully   at  
r

educed
 s
peed.


or
F
I
n the event of a puncture, use the
temporary   puncture   repair   kit   or   the   spare  
w

heel   (according   to   equipment).
Go   to   a   CITROËN   dealer   or   a   qualified  w
orkshop to   have   the   system   checked   or,  
f

ollowing   the   repair   of   a   puncture,   to   have   the  
o

riginal   wheel,   equipped   with   a   sensor,   refitted.
Any
  tyre   repair   or   replacement   on   a   wheel  
f

itted   with   this   system   must   be   carried   out   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
If
  after   changing   a   tyre,   a   wheel   is   not   detected  
b

y   your   vehicle   (fitting   snow   tyres   for   example),  
y

ou   must   have   the   system   reinitialised   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
The loss of pressure detected does not
always
  lead   to   visible   deformation   of   the  
t

yre.   Do   not   rely   on   just   a   visual   check.This alert is also displayed when one or
more
  wheels   is   not   fitted   with   a   sensor  
(

for   example,   a   space-saver   or   steel  
spar

e
 w
heel).
The   alert   is   maintained   until   the   tyre   or  t
yres concerned is reinflated, repaired
or
  replaced.
The
  spare   wheel   (space-saver   type   or   a  
s

teel   rim)   does   not   have   a   sensor.
9
Driving

201
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
The programmed information is grouped together in   the   instrument   panel   screen.
6.
  S

peed   limiter   on   /   off   indication.
7.
  S

peed   limiter   mode   selection   indication.
8.
  P

rogrammed   speed   value.
9.
  S

election   of   a   memorised   speed.
Displays in the instrument panel
Speed limiter
The functions of this system are grouped together   on   the   steering   mounted   controls.
1.
 S

peed   limiter   mode   selection   wheel.
2.
 P

rogrammed   value   decrease   button.
3.
 P

rogrammed   value   increase   button.
4.
 S

peed   limiter   on   /   off   button.
5.
 L

ist   of   memorised   speeds   display   button.
Steering mounted controls
Operation
System which prevents the vehicle from exceeding the speed programmed by the driver.
W hen   the   programmed   speed   limit   is   reached,   pressing   the   accelerator   pedal   no   longer   has   any  
ef

fect.
The
  speed   limiter   is   switched on
 m
anually:
 i

t   requires   a   programmed   speed   of   at   least  
2

0 mph   (30   km/h).
The
  speed   limiter   is   switched off
 
by   manual  
o

peration   of   the   control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly  
b

eyond   the   point   of   resistance.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal.
The
 
p
rogrammed  
s
peed  
r
emains  
i
n  
t
he  
m
emory  
w

hen   the   ignition   is   switched   off.
The speed limiter cannot, in any circumstances, replace   the   need   to   observe   speed   limits,   nor   can   it r

eplace   the   need   for   vigilance   on   the   part   of   the   driver.
9
Driving