2015 Citroen BERLINGO MULTISPACE RHD ignition

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
42
trip recorder zero reset button
after this operation, if you wish
to   disconnect   the   battery,   lock  
the vehicle and wait for at least
five minutes,

  otherwise   the   zero   re-set  
will

 
not   be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on, the
engine oil level is indicated for a few
seconds,
  after   the   service   information. Oil level correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge fault
Flashing of "OIL--"
indicates  
a
 
malfunction of the engine oil level


indicator.   Contact
 a

  CITROËN   dealer   or   a   qualified
 workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.
d
ipstick
A   =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting
reaches

  the   minimum   (or  
maximum)

 
setting,   release   the   button  
then press it again to increase (or
reduce)

 
the
 
brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero re-set
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.
Instruments and controls

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
47
StOP & StArt
The Stop & Start system puts the engine
  temporarily   on   standby   -   STOP mode

  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).  
The
 
engine

  restarts   automatically   -   START
 mode

  -   as   soon   as   you   want   to   move  
of

f.  
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system
  reduces   fuel   consumption   and  
exhaust

  emissions   as   well   as   the   noise  
level

  when   stationary.
Operation
Going into engine StOP mode
The "E c O"   warning   lamp  
comes

  on   in   the   instrument  
panel and the engine goes
into

  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with the 6-speed electronic gear
control gearbox

, at a speed below
5
  mph   (8   km/h),   when   you   press  
the

  brake   pedal   or   put   the   gear  
lever into position

n .If
  your   vehicle   is   fitted   with   the   system,  
a

  time   counter   calculates   the   sum   of  
the

  periods   in   STOP
 
mode   during   a  
journey

.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With   the   automatic   gearbox  
system,

  for   your   comfort   during  
parking

  manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP
 
mode   does   not   affect   the  
functionality of the vehicle, such as
braking,

  power   steering,   for   example.
n

ever refuel with the engine in
STOP
 
mode;   you   must   switch   off  the
  ignition   with   the   key.Special cases: S t
OP
mode
unavailable
STOP
 
mode   is   not   invoked   when:
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded
6 mph

  (10   km/h)   since   the   last  
engine

  start   using   the   key,
-  
the
  engine   is   needed   to   maintain  
a

  comfortable   temperature   in   the  
passenger

  compartment,
-  
demisting
  is   on,
-  
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.
In this case, the
"E c O"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
t

his operation is perfectly normal.
Stop & Start
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
49
reactivation
Press the "EcO OFF" switch again.
The   system   is   active   again;   this   is  
confirmed

  by   the   switch   warning  
lamp

  going   off   and   a   message   in   the  
instrument

  panel.
The
  system   is   reactivated  
automatically

  at   every   new   start  
using

  the   key.
Operating fault
In the event of a malfunction with  the   system,   the   "E c O
OFF"
  switch   warning   lamp  
flashes,

  then   comes   on  
continuously

.
Maintenance
Before working under the bonnet, deactivate  the   Stop   &   Start   system  
to

  avoid   any   risk   of   injury   resulting  
from

  automatic   operation   of   START
 mode.
This

  system   requires   a   specific  
battery

  with   a   special   specification  
and

 
technology   (reference   numbers  
available

  from   a   CITROËN   dealer   or   a  
qualified

  workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
The
  Stop   &   Start   system   makes  
use

  of   advanced   technology.  
All
 
work

  on   this   type   of   battery   must  
be done only by a CITR

o Ë n dealer or
a
 
qualified   workshop.
have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 

mode,
 
the

 
vehicle
 
may
 
stall.
 
All

 
of
 
the
 
warning
 
lamps

 
in
 
the
 
instrument
 
panel
 
come
 
on.

 
It
 
is
 
then
 
necessary
 
to
 
switch
 
off
 
the ignition and start the engine again
using

 
the
 
key.
Stop & Start
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
50
Good practice when stopping Good practice when starting
diesel pre-heating warning
lamp
If
  the   temperature   is   high  
enough,

  the   warning   lamp  
comes

  on   for   less   than  
one

second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp
 
to
 
go   off   then   operate   the   starter  
(Starting position) until the engine
starts.
d
oor or bonnet open
warning lamp
If this comes on, a door or the bonnet is   not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (
d iesel engine) to
return
  to   idle.
d

o not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
StArt I n G A nd S tOPPI n G
running and accessories position.
T o   unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
S
t
OP
position:   steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Starting and stopping

52
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
dIrEctIOn IndIcAtOr S
"Motorway" function
Press
  the   control   up   or   down   to   flash  
the corresponding direction indicator
three

  times.
LIGHtInG cOntrOL
Left: downwards passing the point  of   resistance.
r

ight:   upwards   passing   the  
point

  of   resistance.
Front and rear lighting
Lighting off
Automatic
  illumination   of  
headlamps
SidelampsDipped

  beam   (green)
Main
  beam   (blue)
d

ipped beam/main beam
change
Pull
 
the
 
stalk   fully   towards   you.
Lighting-on audible warning
o

n switching off the ignition, all of the
lamps
 
turn   off,   except   dipped   beam   if  
automatic

  guide-me-home   lighting   has  
been

 
activated.
To activate the lighting control, turn
ring A to the lighting off position "0"
then
 
to
 
the   selection   of   your   choice.
o

n opening the driver's door, there is
an audible warning if you have left the
lighting
 
on.
 Checking

 
by
 
means
 
of
 
the
 
indicator

 
lamps
 
in
 
the
 
instrument
 
panel is described in the
"Instruments

 
and
 
controls"
 
section
 
of

 
chapter
 
3.
direction indicators
Selection is by turning ring A.
Steering mounted controls

54
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEAdLAMP BEAM
depending on the load in your vehicle,
the   beam   setting   must   be   adjusted.
0 -
 
No
  load.
1 -
 
Partial
  load.
2 -
 
A
verage   load.
3 -
 
Maximum
  authorised   load.
Manual operation
-
 With
 
the
 
ignition
 
off,
 
"flash"
 
the
 headlamps
 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manouevres...).
cornering lighting
travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Steering mounted controls

55
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
2  Fast  wipe   (heavy   rain).
1   
Normal
  wipe   (moderate   rain).
l
  
Intermittent
  wipe.
0
  
Of
f.
â

Single wipe
 (press

  downwards).
In the Intermittent
  position,   the   wiping  
speed is in proportion to the vehicle
speed.
WIndScrEEn WIPEr StALK
Manual windscreen wipers
Whenever the ignition has been
switched   off   for   more   than   one   minute,  
with

  the   windscreen   wiper   stalk   in  
position

  2,   1   or   I,   the   stalk   must   be  
reactivated:
-

 
move
  the   stalk   to   any   position,
-
 
then
  move   it   back   to   the   required  
position.
d

o not cover the rain sensor,
located in the centre of the
windscreen,
  behind   the   mirror.Activation
Press
  the   control   downwards.  
a ctivation of the function is
accompanied   by   a   message   in   the  
screen.
d

eactivation / Switching off
Place   the   windscreen   wipers   stalk   in  
position

I, 1 or 2.   Deactivation   of   the  function
  is   accompanied   by   a   message  in
  the   screen.
In
  the   event   of   malfunction   of   the  
automatic

  windscreen   wipers,   the  
windscreen wipers will operate in
intermittent

  mode.
Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked. In the
A ut
O
position, the windscreen
wipers   operate   automatically   and  
adapt their speed to the intensity of the
rainfall.
When not in

A ut
O
  mode,   for   the  
other

  positions,   refer   to   the   manual  
windscreen

  wipers   section.
The   automatic   rain   sensitive  
windscreen

  wipers   function   must  
be

  reactivated   by   pressing   the   stalk  
downwards, if the ignition has been
switched

  off   for   more   than   one   minute.
When   using   an   automatic   car  
wash, switch of

f the ignition to
avoid
  triggering   the   automatic  
wiping.
In winter

, it is advisable to wait for the
windscreen
  to   completely   clear   of   ice  
before

  operating   automatic   wipe.
Automatic rain sensitive windscreen wipers
Steering mounted controls
EaSE oF USE and CoMFoRT
4

56
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
Screenwash and headlamp wash
Pull the stalk towards you, the wash-
wipe   is   accompanied   by   a   timed   sweep  
of

  the   wipers.
The
  headlamp   wash   is   linked   with   the  
wash-wipe, it is triggered if the dipped
headlamps

  are   on.
Turn
  the   ring   past   the   first  
position:

  the   rear   screenwash  
then the rear wiper operates
for

  a   fixed   time.
In winter, in the event of a
considerable
  amount   of   snow  
or ice, switch on the heated
rear

  screen.   Once   the   screen   is  
clear

,   remove   the   snow   or   ice   which  
has

  accumulated   on   the   rear   wiper  
blade.

 
Y
ou   can   then   operate   the   rear  
windscreen

  wiper.
To top up the levels, refer to the
"Levels"
  section   of   chapter   7.
Special position of the
windscreen wipers
In the minute following switching off of the ignition, any action on the
stalk
  positions   the   wipers   against   the  
windscreen

  uprights.
This action enables you to position
the
  wiper   blades   for   winter   parking,  
cleaning

  or   replacement.
Refer to the "Changing a windscreen
wiper
  blade"   section   of   chapter   8.
To
  park   the   wipers   in   their   normal  
position after this has been done,
switch

  on   the   ignition   and   move   the  
stalk. T

urn   the   ring   to   the   first  
position.
rear wiperrear screenwash
Steering mounted controls