2015 Citroen BERLINGO MULTISPACE RHD ignition

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
174
dASHBOArd FuSES
Tilt the cover to gain access to the
fuses.Fuses
F Amperes  Aa
llocation
1 15 Rear wiper
2 - Spare
3 5
a

irbag
4 10 Air
  conditioning,   diagnostic   socket,   mirror   control,  
headlamp

  beam
5 30 Electric windows
6 30Locks
7 5Rear
  courtesy   lamp,   front   map   reading   lamp,   roof  
console
8 20 Audio

  equipment,   screen,   tyre   under-inflation  
detection,

  alarm   and   siren
9 30Front
  and   rear   12V   socket
10 15 Central
  column
11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument
  panel
14 15 Parking
  sensors,   digital   air   conditioning   controls,  
hands-free

  phone   kit
15 30 Locks
16 - Spare
17 40Rear
  screen/mirrors   demist/defrost
Changing a fuse

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
177
Placing the windscreen wiper
blades in the special position
- Less  than   a   minute   after   switching  of
f  the  ignition,  press  the  wiper  stalk  
downwards to position the wiper
blades along the windscreen pilla

rs
(special
  position).
c
hanging a front wiper blade
-  
Lift
  the   wiper   arm.
-  Unclip   the   blade   and   remove   it.
-  Fit   the   new   blade.
-
 
Push
  back   the   wiper   arm.
To return the windscreen wipers to
their
  normal   position,   switch   on   the  
ignition

  and   operate   the   wiper   stalk.
c
hanging the rear wiper blade
-  
Lift
  the   wiper   arm,   then   unclip   the  blade
  and   remove   it.
-  Fit   the   new   blade   and   push   back  
the

  wiper   arm.
cHAnGInG A WIPEr BLAdE
Changing a wiper blade
QUICk HELP
8

10.2
Berlingo_2_VP_en_Chap10a_BTa_ed02-2014
EMErGEncY O r ASSIS tA nc E c ALL
cItrOËn Localised Emergency call
In an emergency, press this button for more than 2 seconds. Flashing
  of   the   green   LED   and   a   voice   message   confirm  
that

  the   call   has   been   made   to   the   CITROËN   Localised  
Emergency

  Call   centre*.
Pressing
 
this   button   again   immediately   cancels   the   call.  
The
  green   LED  
goes

 
off.
Pressing
 
this   button   (at   any   time)   for   more   than   8   seconds   cancels   the  
call.
cItrOËn Localised Assistance call
When the ignition is switched on, the green
LED  comes   on   for   3   seconds   indicating   that  
the

  system   is   operating   correctly.
If
  the   orange   LED   flashes:   there   is   a   system  
fault.
If

  the   orange   LED   is   on   continuously:   the  
backup

  battery   must   be   replaced.
In
  either   case,   contact   a   CITROËN   dealer.
Pressing
 
this
 
button
 
again
 
immediately   cancels   the   request.
The
 
cancellation
 
is
 
confirmed
  by   a   voice   message.
Press
 
this
 
button   for   more   than   2   seconds   to   request  
assistance

 
if
 
the   vehicle   breaks   down.
A
 

voice
 
message   confirms   that   the   call   has   been   made*.
Operation of the system
The green LED remains on (without flashing) when communication is established.
  It   goes   off   at   the   end   of   communication.
This
  call   is   dealt   with   by   the   CITROËN   Localised   Emergency   Call   centre  
which

  receives   locating   information   from   the   vehicle   and   can   send   a  
detailed

  alert   to   the   appropriate   emergency   services.   In   countries   in  
which

  the   team   is   not   operational,   or   when   the   locating   service   has  
been

  expressly   declined,   the   call   is   dealt   with   directly   by   the   emergency  
services

  (112)   without   the   vehicle   location.
If
  an   impact   is   detected   by   the   airbag   control   unit,   and  
independently

  of   the   deployment   of   any   airbags,   an   emergency  

call

  is   made   automatically.
*
 
These
  services   are   subject   to   conditions   and   availability.
 Consult

  a   CITROËN   dealer. If
  you   purchased   your   vehicle   outside   the   CITROËN   dealer   network,  
we

  invite   you   to   have   a   dealer   check   the   configuration   of   these   services  
and,

  if   desired,   modified   to   suit   your   wishes.   In   a   multi-lingual   country,  
configuration

  is   possible   in   the   official   national   language   of   your   choice.
For
  technical   reasons,   particularly   to   improve   the   quality   of  
T
elematic  
services

  to   customers,   the   manufacturer   reserves   the   right   to   carry   out  
updates

  to   the   vehicle's   on-board   telematic   system.
If
  you   benefit   from   the   CITROËN   eTouch   offer,   you   also   have   available  
additional

services in your MyCITR o Ë n personal space, via the CITR o Ë n
Internet
  website   in   your   country,   accessible   on   www.citroen.com.

06
10.27
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
uSInG tHE tELEPHOnE
Select "connect" and confirm.
The   system   offers   to   connect   the  
telephone:
-


in "
Hands-free mode" (telephone
only),
-

in "
Audio"   mode   (streaming:   playing  
music

  files   on   the   telephone),
-

or "
All" (for selection of both
modes).
Select "OK"
  and   confirm. Then
  accept   automatic   connection   on   the   telephone   to   allow   the  
telephone

  to   reconnect   automatically   every   time   the   vehicle   is  
started.
The

 
ability   of   the   system   to   connect   in   only   one   mode   depends   on  
the

 
telephone.  
The
  two   modes   may   both   connect   by   default.
The "Hands-free mode" should be used in preference if
"Streaming"
  is   not   desired.
The
 
services   available   depend   on   the   network,   the   SIM   card   and   the   compatibility   of   the   Bluetooth   telephone   used.   Check   the   telephone  
manual

 
and   with   your   network   provider   for   details   of   the   services   available   to   you.
Depending   on   the   type   of   telephone,   the   system   will   ask   you   to  
accept

  or   not   the   transfer   of   your   contacts.
o

n return to the vehicle,the last telephone connected
automatically
  reconnects,   within   around   30   seconds   after  
switching

  on   the   ignition   (Bluetooth   activated   and   visible).
To
  modify   the   automatic   connection   mode,   remove   the   pairing  
and

  pair   the   telephone   again   with   the   desired   mode.
Enter
  a   minimum   4   figure   code   in   the   telephone  
and

  confirm.
Enter   the   same   code   in   the   system,  
select "

OK"   and   confirm.
Select
  the   name   of   the   desired  
peripheral

  from   the   list   of   devices  
detected

  then   confirm.

08
10.40
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
Insert the Cd in the player, insert the USB
memory   stick   in   the   USB   player   or   connect   the  
USB peripheral to the USB port using a suitable
cable

  (not   supplied).
The
  system   builds   playlists   (in   temporary  
memory),

  an   operation   which   can   take   from  
a

  few   seconds   to   several   minutes   at   the   first  
connection.
Reduce

  the   number   of   non-music   files   and   the  
number

  of   folders   to   reduce   the   waiting   time.
The
  playlists   are   updated   every   time   the   ignition  
is

  switched   off   or   connection   of   a   USB   memory  
stick.

  However,   the   system   memorises   these  
lists

  and   if   they   are   not   modified,   the   loading  
time

  will   be   shorter.
Play
  starts   automatically   after   a   period   which  
depends

  on   the   capacity   of   the   USB   memory  
stick. Selection of source
The
SO urc E   button   on   the   steering   mounted   controls   allows   a  direct
  change   to   the   next   media   source.
" cd / cd MP3"
"
u SB, iPod"
"A
u X"
"S
tr EAMI n G"
"
r A d IO"
Press M
u SI c to display the "ME d IA"
menu.
Select "Following media source " and
confirm.
Repeat
  the   operation   as   many   times   as   necessary   to   obtain   the  
desired

  media   source   (except   for   radio   which   is   accessible   either  
with

SO urc E or r A d IO).
Sources
MuSIc MEdIA
PLAYE r S

11
10.47
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
trIP cOMP ut E r
trip computer
Press the ModE button several
times   in   succession   until   the   trip  
computer

  is   displayed.
r

ange: displays the distance which can travelled with the
remaining
  fuel   detected   in   the   tank,   basd   on   the   average  
consumption

  over   the   last   few   miles   (kilometres).
This
  displayed   value   may   vary   significantly   following   a   change   in  
the

  vehicle   speed   or   the   relief   of   the   route.
When
  the   range   falls   below   20   miles   (30   km),   dashes   are  
displayed.

 
After
  filling   with   at   least   10   litres   of   fuel,   the   range   is  
recalculated

  and   is   displayed   when   it   exceeds   60   miles   (100   km).
If, whilst driving, dashes are displayed continuously in place of the
digits,
  contact   a   CITROËN   dealer.
c

urrent fuel consumption:

only calculated and displayed above
20
  mph   (30   km/h).
Average fuel consumption:
 

this   is   the   average   fuel   consumption  
since

  the   last   trip   computer   zero   reset.
d

istance travelled:
 
calculated   since   the   last   trip   computer   zero  
reset.
d

istance remaining to the destination:

calculated with reference
to
  the   final   destination,   entered   by   the   user.   If   guidance   is  
activated,

  the   navigation   system   calculates   it   as   a   current   value.
Average speed: this is the average speed calculated since the last
trip
  computer   zero   reset   (ignition   on).
Each
 
press
 
of   the   button   at   the   end   of   the   wiper   stalk   displays   the  
dif

ferent
 
trip
 
computer   information   in   succession,   according   to   the  
screen.
A few definitions
- The  "vehicle"   tab:
The range, the current fuel
consumption

  and   the   distance  
remaining.
-

 
The
  "1"   (trip   1)   tab   with:
The average speed, the average
fuel

  consumption   and   the  
distance travelled calculated
over

  route   "1".
-
 
The
  "2"   (trip   2)   tab   with   the   same  
functions

  for   a   second   route.

05
10.66
Berlingo_2_VP_en_Chap10c_Rd45_ed02_2014
uSB PLAYEr
The system puts together playlists (temporary memory) created over  a   period   which   depends   on   the   capacity   of   the   USB   device.
The
  other   sources   are   available   during   this   time.
The
  playlists   are   updated   each   time   the   ignition   is   switched   off   or  
each

  time   a   USB   memory   stick   is   connected.
When
  connecting   for   the   first   time,   the   classification   suggested  
is

  by   folder.   When   you   reconnect,   the   classification   selected  
previously

  is   retained.Connect
  the   memory   stick   to   the   port,   directly   or  
using

  a   lead.   If   the   audio   equipment   is   switched  
on, the USB source is detected as soon as it
is

  connected.   Play   begins   automatically   after   a  
delay which depends on the capacity of the USB
memory

  stick.
The   file   formats   supported   are   .mp3   (mpeg1  
layer

  3   only)   and   .wma   (standard   9   only,  
128 kbits/sec

  compression).
Certain   playlist   formats   are   supported   (.m3u,   ...)
On   reconnection   of   the   previous   memory   stick  
used,

  play   is   resumed   automatically   with   the   last  
track

  played.
This unit consists of a USB port and an auxiliary
Jack
 
socket*.
 
The

 
audio
 
files
 
are
 
transmitted
 
from

 
a
 
portable
 
device
 
-
 
digital
 
player
 
or
 
a
 
USB
 
memory

 
stick
 
-
 
to
 
your
 
Audio

 
system
 
and
 
heard
 
via

 
the
 
vehicle's
 
speakers.
USB
 
memory
 
stick
 
or
 
Apple® player of
generation
 
5
 
or
 
later:
-
 
Give

 
preference
 
to
 
multimedia   USB   memory  
sticks

 
(in
 
general
 
formatted   FAT
 
32   File  
a
llocation Table),
-

the

a
pple
® player lead is essential,
-
 
navigation

  through   the   file   database   is   also  
possible

 
by   means   of   the   steering   mounted  
controls.
using the uSB BOX
connecting a uSB memory stick
o

ther
a
pple
® players of earlier generations and
players
 
using   the   MTP  protocol*:
-
 
play

 
via
 
Jack-Jack   lead   only   (not   supplied),
-
 
navigation
  through   the   file   database   is   from  
the

 
portable   device. *
  Depending   on   vehicle.

06
10.69
Berlingo_2_VP_en_Chap10c_Rd45_ed02_2014
BLuEtOOt H F unct IO n S
For safety reasons and because they require prolonged attention on the part of the driver
, the operations for pairing of the Bluetooth
mobile
  telephone   with   the   Bluetooth   hands-free   system   of   your  
audio

  equipment   must   be   carried   out   with   the   vehicle   stationary  
and

  the   ignition   on.
Press
  the   MENU   button.
A
 

window   is   displayed   with   a   message   that   a   search   is   in   progress.
a
ctivate the telephone's Bluetooth function
and ensure that it is "visible to all" (telephone
configuration).
In
  the   menu,   select:
-
Bluetooth telephone function - a

udio
-
 
Bluetooth
  configuration
-
 
Perform
  a   Bluetooth   searchThe
  services   offered   depend   on   the   network,   the   SIM   card   and   the  
compatibility

  of   the   Bluetooth   equipment   used.
Consult   your   telephone's   manual   and   your   operator   to   find   out   which  
services

  are   available   to   you.
Bluetooth telephoneScreen c
The

 
TELEPHONE
  menu   permits   access   to   the   following   functions  
in

  particular:   Directory*,   Call   list,   Pairing   management.
The
  first   4   telephones   recognised   are   displayed   in   this   window.
A
 

virtual   keypad   is   displayed   in   the
 screen:

  enter   a   code   with   at   least   4   digits.
Confirm
  by   pressing   OK.
A
 

message   that   the   pairing   has   been   successful   appears   in   the  
screen. Select
  the   telephone   to   be   connected   from   the   list.   Only   one  
telephone

  can   be   connected   at   a   time.
A
 

message   is   displayed   in   the   screen   of   the  
telephone

  chosen.  
T
o   accept   the   pairing,   enter   the  
same

  code   on   the   telephone,   then   confirm   with   OK.
The
  automatic   connection   authorised   is   only   active   after   the  
telephone

  has   been   configured.
The directory and the call list can be accessed after the
synchronisation
  period.
(Available according to model and version)
*
  If   your   telephone   is   fully   compatible.
If
  pairing   fails,   the   number   of   attempts   is   not   limited.
Go
  to   www.citroen.co.uk   for   more   information   (compatibility,   more  
help,

  ...).
Pairing a telephone / First connection