2015 Citroen BERLINGO MULTISPACE wheel

178
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
SNOW CHAINS
In wintry conditions, snow chains
improve  traction   as   well   as   the  
behaviour

  of   the   vehicle   when   braking.
 The

  snow   chains   must   be   fitted  
only

  to   the   driving   wheels.  
They
 
must

  never   be   fitted   to   "space-
saver"
  type   spare   wheels.
 T

ake   account   of   the   legislation   in  
force in your country on the use
of

  snow   chains   and   the   maximum  
running

  speed   authorised.Advice on installation
F
 
If
  you   have   to   fit   the   chains   during  
a

  journey,   stop   the   vehicle   on   a   flat  
surface

  on   the   side   of   the   road.
F
 
Apply
  the   parking   brake   and  
position

  any   wheel   chocks   to  
prevent

  movement   of   your   vehicle.
F

Fit the chains following the
instructions provided by the
manufacturer

.
F

Move of
f gently and drive for a
few
  moments,   without   exceeding  
30

  mph   (50   km/h).
F
 
Stop
  your   vehicle   and   check   that  
the snow chains are correctly
tightened.It

  is   recommended   that   before   you  
leave,

  you   practise   fitting   the   snow  
chains

  on   a   level   and   dry   surface.
Use only the chains designed to be
fitted
  to   the   type   of   wheel   fitted   to   your  
vehicle:
For

  more   information   on   snow   chains,  
contact a CITR

o Ë n dealer or a
qualified
  workshop.
o
riginal
tyre size Maximum
  link  
size.
195/65

  R159
  mm
195/70
  R15
205/65
  R15
215/55
  R16
215/50
  R17
avoid driving with chains on roads
that have been cleared of snow

,
to
  avoid   damaging   your   vehicle's   tyres  
and

  the   road   surface.   If   your   vehicle  
is

  fitted   with   alloy   wheels,   check   that  
no

  part   of   the   chain   or   its   fixings   is   in  
contact

  with   the   wheel   rim.
Snow chains

181
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
3. Direction indicators
T ype B,   PY21W   -   21W   (amber)
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-
 
Remove
  the   bulb   by   pressing   it  
lightly

  while   turning   it   anticlockwise.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing. 4.

Front foglamps
T ype C, H1 - 55W
-
 
Remove
  the   three   clips   and   the  
screw securing the wheel arch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheel   arch   liner   upwards.
-
d isconnect the bulb holder
connector by pressing the tab at
the
  top.-
 
Remove
  the   bulb   holder   by  
squeezing the two clips (at top and
bottom)

  using   a   finger   and   thumb.
-
 
Replace
  the   module   (bulb   holder  
and

  bulb.
-

Carry out the operations in reverse
order

  to   fit   the   module   and   refit   the  
wheel

  arch   liner.
QUICk HELP
8
Changing a bulb

183
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time   is  
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
on
 
bulbs,
 
refer
 
to
 the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B,
 
PY21W
 
-
 
21W
 
(amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
QUICk HELP
8
Changing a bulb

188
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
Fuses under the bonnet
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  Aa
llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
  motor
9 10Headlamp
  beam   motor,   fleet   management   unit
10 30 Engine
  components
11 40
n

ot used
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
Changing a fuse

190
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
Without lifting (4 wheels on
the road)
You should always use a towing arm.
BEING TOWED
This procedure involves the use of
the towing eye supplied with the tools
for
  changing   a   wheel.
From the front
- Unclip the cover by pressing the
bottom  part.
-
 
Fully
  screw   in   the   removable   towing  
eye.
From the rear
- Unclip the cover using a coin or the
flat  part   of   the   towing   eye,
-
 
Fully
  screw   in   the   removable   towing  
eye. When towing with the engine
switched

  off,   there   is   no   braking   or  
steering

  assistance.
Lifting (only 2 wheels on the
road)
It is preferable to raise the vehicle
using
  professional   lifting   equipment.Vehicles fitted with a manual
gearbox (Diesel version)
In
  the   case   of   vehicles   fitted   with  
a

  manual   gearbox,   the   gear   lever  
must

  be   in   neutral,   failure   to   observe  
this

  special   condition   may   result   in  
damage

  to   transmission   and   braking  
components

  and   the   absence   of  
braking

  assistance   when   the   engine   is  
started

  again.
Chapter
 
9,
 
"Changing
 
a
 
wheel"
 
section.
Having your vehicle towed

 193
Berlingo-2-VP_en_Chap09_Caract-technique_ed01-2015
Berlingo-2-VP_en_Chap09_Caract-technique_ed01-2015
DIMENSIONS (MM)
Loverall length 4380
H
o
verall height 1801-1862
aWheelbase 2728
B Front overhang 925
C Rear overhang 727
dWidth

  over   panels: without
  mirrors1810
with
  mirrors2112
E Width
  of   front   tracks 1505-1507
F Width
  of   rear   tracks 1554-1556
- Length of the loading surface to the
seat Row 2
990
Row 2, seat fully folded 1343
With front passenger seat folded 3000
Dimensions
TECHNICAL DATA
9

200
Berlingo-2-VP_en_Chap09_Caract-technique_ed01-2015Berlingo-2-VP_en_Chap09_Caract-technique_ed01-2015
IDENTIFICATION MARKINGS
A. Manufacturer's plate.C. Tyres and paint colour code.
The label C,
  on   the   front   door   gives:
-
the wheel and tyre sizes,
-

the tyre pressures, laden and
unladen,
-

the tyre pressure of the spare
wheel,
-
 
the
  paint   colour   code.
The   tyre   pressures   should   be   checked  
when

  cold,   at   least   once   a   month.
B. Serial number.
This is engraved on the front right
wheelarch.
If
  your   vehicle   is   fitted   with   the
 system,

  refer   to   the   "Under-inflation
 detection"

  section   in   Chapter   3.
Identification markings

 273
Berlingo-2-VP_en_Chap10b_Rd45_ed01-2015
Receiving a call
An incoming call is announced by a ring and a superimposed   display   in   the   screen.
Select the YES tab on the display
using
  the   buttons.
Confirm
  by   pressing   OK.
Press this button at the steering
mounted
  controls   to   accept   the   call.
Making a call
From the Bluetooth: Telephone - Audio"
menu.
Select " Manage the telephone call".
Select " Call".
o

r
Select " Calls list ".
o

r
Select " Directory ".
Press
  this   button   for   more   than  
t

wo seconds for access to your
directory, then navigate using the
thumb
  wheel.
o

r
To
  dial   a   number,   use   your   telephone's   keypad,  
w

ith   the   vehicle   stationary.
Ending a call
during a call, press this button for
more  than   2   seconds.
Confirm
 
with   OK
 
to   end   the   call.
The
  system   accesses   the   telephone's  
c

ontacts directory, depending on its
compatibility,
  and   while   it   is   connected  
b

y
 
Bluetooth.
With certain telephones connected by
Bluetooth you can send a contact to the
directory
  of   the   audio   system.
Contacts
  imported   in   this   way   are  
s

aved   in   a   permanent   directory  
v

isible to all, whatever the telephone
connected.
The
  menu   for   the   directory   is   not  
a

ccessible   if   it   is   empty.
audio and Telematics
TECHnoLoGY on BoaRd
10