2015 Citroen BERLINGO MULTISPACE wheel

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
47
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
6-SPEED ELECTRONIC GEARBOx
- automatic  mode:   gear   selector   in  position
A.
-
 
manual
  mode:   gear   selector   in  
position

M.
For
  safety:
It
  is   only   possible   to   come   out  
of position

N   if   the   brake   pedal   is  
pressed.
The

  change   from   position   A (driving in
automatic
  mode)   to   position   M (driving
in
  manual   mode)   or   vice   versa   can   be  
made

  at   any   time.  
The
  warning   lamp   A
goes
  off   in   the   instrument   panel.
Mode selection Moving off
- To start the engine, the gear
selector   must   be   in   position   N.
-
 
Press
  firmly   on   the   brake   pedal.
-
 
Operate
  the   starter.
-

When the engine is running, place
the gear selector on

R, A or M as
desired.
-
 
Release
  the   brake   pedal   and  
accelerate.
If the gear selector is not in position

N,
and/or
  if   the   brake   pedal   is   not  
pressed,

  the   engine   will   not   start.  
Repeat

  the   above   procedure.
Reverse gear Engaging reverse gear
Move the gear selector to R.
Only attempt to select reverse gear
when the vehicle is stationary.
Neutral Changing to neutral
Move the gear selector to N.
  If   the  
vehicle

  is   moving,   do   not   select   this  
position

  even   momentarily.
Gearbox and steering wheel
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
48
Acceleration
For optimum acceleration (e.g. to overtake  another   vehicle),   simply  
press the pedal beyond the point of
resistance at the end of its travel, by
pressing

  down   firmly.
Vehicle stationary, with the
engine running
In the event of a prolonged stop with
the engine running, the gearbox
changes  automatically   to   neutral   N.
Stopping the vehicle
Before stopping the engine, put the
gear selector in position N.
In all cases, it is essential to apply
the
  parking   brake.   Check   that   the  
parking

  brake   warning   lamp   is   on   in   the  
instrument

  panel.
Before doing anything in the
engine
  compartment,   check   that  
the gear selector is in neutral

N.
Changing gear
In situations of high engine speeds
(heavy acceleration), a change
up will not occur unless the driver
operates the electronic gearbox control
paddle. Pull on the "+" control
paddle
  to   change   up.
Pull on the "-" control
paddle to change
down.
-

If the vehicle stops or reduces
speed

  (for   example   when  
approaching a stop sign),
the gearbox changes down
automatically

,   to   first   gear   if  
needed.
-


It is not necessary to release the
accelerator

  completely   during   gear  
changes.
-

a
gear change instruction is
accepted only if the engine speed
permits.
-


For safety reasons, depending on
the engine speed, a change down
may

  be   performed   automatically.
Manual mode
Changing to manual mode
Move the gear selector to M. Automatic mode Changing to automatic
mode
Move the gear selector to A.
The gearbox then operates in
automatic
 
mode,
 
without
 
any
 
action
 
on
 
your

 
part.
It constantly selects the gear that is
best
 
suited
 
to
 
the
 
following
 
conditions:
-

driving style,
-

 
road

 
profile,
-
 
optimum

 
fuel
 
consumption.
Gearbox and steering wheel

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
52
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If  the   temperature   is   high  
enough,

  the   warning   lamp  
comes

  on   for   less   than  
one

second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp
 
to
 
go   off   then   operate   the   starter  
(Starting position) until the engine
starts.
Door or bonnet open warning lamp
If  this   comes   on,   a   door   or   the   bonnet
 is

  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (
d iesel engine) to
return
  to   idle.
d

o not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Starting and stopping

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
54
A FEW DRIVING
RECOMMENDA
TIONS
observe the driving regulations at all
times   and   remain   vigilant   whatever   the  
traffic

  conditions.
Pay
  close   attention   to   the   traffic   and  
keep

  your   hands   on   the   wheel   so   that  
you

  are   ready   to   react   at   any   time   to  
any

  eventuality.
On
  a   long   journey,   a   break   every   two  
hours

  is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,  
anticipate

  the   need   to   brake   and  
increase

  the   distance   from   other  
vehicles.
Driving on flooded roads
We strongly advise against driving
on  flooded   roads,   as   this   could   cause  
serious

  damage   to   the   engine   or  
gearbox, as well as to the electrical
systems

  of   your   vehicle. If you are obliged to drive through
water:
-
 
check
  that   the   depth   of   water   does  
not

  exceed   15   cm,   taking   account  
of

  waves   that   might   be   generated  
by other users,
-
 
deactivate
  the   Stop   &   Start   system,
-
drive as slowly as possible without
stallin

g.   In   all   cases,   do   not   exceed  6
  mph   (10   km/h),
- do not stop and do not switch of f
the
  engine.
On
  leaving   the   flooded   road,   as   soon  
as

  circumstances   allow,   make   several  
light

  brake   applications   to   dry   the   brake  
discs

  and   pads.
If in doubt on the state of your vehicle,
contact a CITR
o Ë n dealer or a
qualified
  workshop.Never
  drive   with   the   parking   brake  
applied

  -   Risk   of   overheating   and  
damage

  to   the   braking   system!
Do   not   park   or   run   the   engine   when  
stationary

  in   areas   where   inflammable  
substances

  and   materials   (dry   grass,  
dead

  leaves...)   might   come   into   contact  
with

  the   hot   exhaust   system   -   Risk   of  
fire!
n

ever leave a vehicle
unsupervised with the engine
running.   If   you   have   to   leave  
your vehicle with the engine running,
apply

  the   parking   brake   and   put   the  gearbox into neutral or position
N or P,
depending
  on   the   type   of   gearbox.
Important!
Starting and stopping

 57
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 With
 
the
 
ignition
 
off,
 
"flash"
 
the
 headlamps
 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manouevres...).
Cornering lighting
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Steering mounted controls
EASE OF USE and COMFORT
4

 91
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
FRONT FITTINGS
1. Lower glove box
This may or may not be fitted with a lid.
Upper storage compartment
This is located on the dashboard,
behind  the   steering   wheel.
A
 

recess   makes   lifting   of   the   lid   easier  
when

  opening.   Guide   it   to   its   rest  
position.
T

o close, guide the lid then press the
centre
  gently.
Any
  liquid   which   could   spill   risks  
causing an electrical short circuit and
therefore

  a   potential   fire.
3. Side storage compartment
4. Bag hook
Only hang flexible bags which are not too  heavy   on   this   hook.
2. Storage pocket and bottle
holder (1.5 L)
EASE OF USE and COMFORT
4
Practical information

 99
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
MODUTOP ROOF BARS
The maximum authorised weight on each
  roof   bar   is   35   kg. In
  all   cases,   the   load   must   rest   on  
the non-slip bands provided for this
purpose

  and   must   not   touch   the   roof   or  
the

  glazing   of   the   roof.
Recommendations for loading the
roof
This procedure requires the use of
a spanner supplied with the tools for
changing
  a   wheel.
These two longitudinal Modutop roof
bars   can   be   removed.
Chapter   9,   "Changing   a   wheel"  section.
-
 
Open
  the   protective   covers.
-
 
Slacken
  the   four   screws   using   the  
spanner

  and   remove   them.
-
 
T
urn   the   bars   90°   placing   the  
hollow

  parts   towards   the   front.
-
 
Refit
  the   the   4   screws   and   tighten  
them

  using   the   spanner.
-
 
Close
  the   protective   covers.
-

Use the strap passages
A only to
secure
  the   load   firmly.
EASE OF USE and COMFORT
4
Practical information

111
Berlingo-2-VP_en_Chap05_Securite_ed01-2015
HAZARD WARNING LAMPS
H
ORN
Press the centre of the steering wheel.
PARKING BRAKE
Applying
Pull the parking brake lever up to immobilise
  your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The
 
hazard
 
warning
 
lamps
 
should
 
only
 
be used in dangerous situations, when
stopping

 
in
 
an
 
emergency
 
or
 
when
 
driving

 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels

  towards   the   pavement   and   pull  
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated
  by   this   warning   lamp   which
 comes

  on   on   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the  hazard   warning   lamps   come  
on

  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It

  is   also   possible   to   switch   them   off   by  
pressing

  the   switch   on   the   dashboard.Releasing
Pull the lever up slightly and press the
button  to   lower   the   parking   brake   lever.
driving safely
SaFETY
5