2015 CHRYSLER TOWN AND COUNTRY turn signal bulb

Multifunction Lever
The multifunction lever is located on the left side of the
steering column.
The multifunction lever controls the:
•Turn Signals
•Headlight Beams Low/High
•Flash-To-Pass
•Front and Rear Wipers — Washer Functions
Turn Signals
Move the multifunction lever up or down and the arrows
on each side of the instrument cluster flash to show
proper operation of the front and rear turn signal lights.
NOTE:If either light remains on and does not flash, or
there is a very fast flash rate, check for a defective outside
light bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is
defective.
Multifunction Lever
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

INSTRUMENT CLUSTER DESCRIPTIONS
1. Tachometer
This gauge measures engine revolutions per minute
(RPM x 1000). Before the pointer reaches the red area,
ease up on the accelerator to prevent engine damage.
2. Front Fog Light Indicator — If Equipped
This indicator will illuminate when the front
fog lights are on.
3. Park/Headlight ON Indicator — If Equipped
This indicator will illuminate when the park
lights or headlights are turned on.
4. Turn Signal Indicators
The arrow will flash with the exterior turn
signal when the turn signal lever is operated.
If the vehicle is driven more than 1 mile (1.6 km) with
either turn signal on, a continuous chime will sound to
alert you to turn the signal off. If either indicator flashes
at a rapid rate, check for a defective outside light bulb.
5. High Beam Indicator
This indicator shows that the high beam head-
lights are on. Push the multifunction lever for-
ward to switch the headlights to high beam, and pull
toward yourself (normal position) to return to low beam.
6. Odometer Display/Electronic Vehicle Information
Center (EVIC) — If Equipped
Odometer Display / Trip Odometer DisplayThe odom-
eter display shows the total distance the vehicle has been
driven.
U.S. Federal regulations require that upon transfer of
vehicle ownership, the seller certify to the purchaser the
correct mileage that the vehicle has been driven. If your
4
UNDERSTANDING YOUR INSTRUMENT PANEL 323

▫Appearance Care And Protection From
Corrosion...........................655
▫Cleaning The Instrument Panel Cupholders . .661
!FUSES..............................661
▫Totally Integrated Power Module (Fuses) . . . .662
!VEHICLE STORAGE....................670
!REPLACEMENT BULBS.................671
!BULB REPLACEMENT..................673
▫High Intensity Discharge Headlamps (HID) — If
Equipped...........................673
▫Quad Headlamps.....................674
▫Front Park/Turn Signal Lamps............674
▫Front Side Marker Lamp................675
▫Front Fog Lamp......................675
▫Rear Turn Signal And Backup Lamp........676
▫Center High-Mounted Stop Lamp (CHMSL) . .677
▫License Lamp........................677
!FLUID CAPACITIES....................678
!FLUIDS, LUBRICANTS AND GENUINE PARTS . .679
▫Engine.............................679
▫Chassis............................681
626 MAINTAINING YOUR VEHICLE

Exterior Bulbs
Bulb Number
Headlamp – (Low and High Beam Halogen)H11LL
Headlamp (HID – If Equipped) Low BeamD1S
Fog Lamp – If EquippedH11LL
Front Side MarkerW5W
Front Park/Turn SignalPY27/7W or 3757A
Rear Turn Signal Lamp3757A
Rear Tail, Stop, and Side Marker LampLED (Serviced at Authorized Dealer)
Center High-Mounted Stop LampLED (Serviced at Authorized Dealer)
Backup Lamp3157
License168
672 MAINTAINING YOUR VEHICLE

Quad Headlamps
1. Raise the hood to access the high or low beam bulbs at
the rear of the headlamp housing.
2. Release the two tabs on the side of the connector and
remove the connector from the bulb.
3. Twist the headlamp bulb and pull the bulb from the
headlamp housing.
4. Install the new headlamp bulb and twist until locked
into the headlamp housing.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
5. Reconnect the wiring connector to the bulb.
Front Park/Turn Signal Lamps
1. Raise the hood to access the rear of the headlamp
housing.
2. Twist the turn signal socket and remove from the
headlamp housing, then pull the bulb out.
3. Push the new bulb into the socket and reinstall the
socket by twisting until locked into the headlamp
housing.
674 MAINTAINING YOUR VEHICLE

2. Disconnect wire harness from the bulb.
3. Reconnect the wiring harness to the new bulb and
reinstall the bulb by twisting clockwise.
Rear Turn Signal And Backup Lamp
1. Raise the liftgate.
2. Remove the tail lamp assembly by removing the two
screws from the inboard side. Use a fiber stick or
similar tool to gently pry the light on the outboard side
to disengage the two ball studs.
Tail Lamp Mounting Screws
676 MAINTAINING YOUR VEHICLE