2015 AUDI S7 weight

M N <( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
If you wish to improve comfort
when operating the vehicle at normal load (up to 2/3* occu­
pants), you can adjust tire
pressures to those specified
for normal vehicle load. Before
operating the vehicle at maxi­ mum load, you must increase
the tire pressures to those
specified for maximum vehicle load
c> .&. .
Bear in mind that the tire pres­
sure monitoring system can on­
ly monitor the tire pressures
you have stored. The system does not recognize the load
condition of your vehicle.
The effectiveness of the tire pressure monitoring system
will be impaired if you store normal load pressures but then
operate the vehicle at its maxi­
mum load
c> .&. .
Tires and wheels 249
See the illustration c> fig. 200
for the location of the label on
driver's side B-pillar (color of
the actual label and exact loca­
tion on the vehicle will vary slightly).
Note that the following table is
accurate at the time of going to
press and is subject to change.
In the event of discrepancies,
the tire pressure label is locat­ ed on the driver's side B-pillar
always takes precedence.
The table below lists the rec­ ommended cold tire inflation pressures for the Audi model
covered by your Owner's Litera­
ture at the vehicle's capacity
weight and the tire sizes instal­
led on the respective models as
original equipment , or as a fac-
tory option. ..,.
•
•
'

technically referred to as the
vehicle's Gross Vehicle Weight Rating ("GVWR"). The Gross
Axle Weight Rating ("GAWR") is
the maximum load that can be applied at each of the vehicle's
two axles. The Gross Vehicle
Weight Rating and the Gross
Axle Weight Rating are listed on the safety compliance stick­
er label located on the driver's
side B-pillar. The tire pressure
label on your Audi lists the
maximum combined weight of
all of the occupants and lug­
gage or other cargo that the ve­
hicle can carry. For the location
of the tire pressure label
c> fig . 200.
A WARNING
-
Overloading a vehicle can
cause loss of vehicle control,
a crash or other accident, se­ rious personal injury, and
even death.
-Carrying more weight than your vehicle was designed to carry will prevent the ve­hicle from handling properly
and increase the risk of a
~ loss of vehicle control. <(
~ -The brakes on a vehicle that has been overloaded may
Tires and wheels 251
not be able to stop the vehi­
cle within a safe distance.
- Tires on a vehicle that has
been overloaded can fail
suddenly causing loss of control and a crash.
-Always make sure that the total load being transported
- including the weight of a
trailer hitch and the tongue
weight of a loaded trailer -
does not make the vehicle
heavier than the vehicle's
Gross Vehicle Weight Rat­
ing.
A WARNING
-Incorrect tire pressures
and/or underinflation can
lead to a serious or fatal ac­
cident.
-Incorrect tire pressures and/or underinflation cause
increased tire wear and can
affect the handling of the
vehicle.
-Incorrect tire pressures and/or underinflation can
also lead to sudden tire fail­
ure, including a blowout
and sudden deflation, caus­
ing loss of vehicle control.
•
•
'

M N <( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
tire failure and loss of
control.
-Excessive speed and/over­ loading can cause heat
build -up, sudden tire failure
and loss of control.
-If the tire pressure is too low or too high, the tires
will wear prematurely and
the vehicle will not handle
well.
-If the tire is not flat and you do not have to change a
wheel immediately, drive at
reduced speed to the near­
est service station to check
the tire pressure and add air as required.
(D Note
Driving without valve stem
caps can cause damage to
the tire valves. To prevent
this, always make sure that
factory installed valve stem caps on all wheels are secure­
ly mounted on the valve.
@ For the sake of the environment
Underinflated tires will also
increase the fuel consump­
tion.
Tires and wheels 255
Tires and vehicle load limits
'
There are limits to the amount of load or weight that any vehi­
cle and any tire can carry. Ave­
hicle that is overloaded will not
handle well and is more diffi­
cult to stop. Overloading can
not only lead to loss of vehicle
control, but can also damage important parts of the vehicle
and can lead to sudden tire fail­
ure, including a blowout and
sudden deflation that can cause
the vehicle to crash.
Your safety and that of your passengers also depends on
making sure that load limits are
not exceeded. Vehicle load in­
cludes everybody and every­
thing in and on the vehicle .
These load limits are technical­ ly referred to as the vehicle's
Gross Vehicle Weight Rating
("GVWR").
The "GVWR" includes the
weight of the basic vehicle, all
factory installed accessories, a
full tank of fuel, oil, coolant and other fluids plus maximum ""
•
•
'

256 Tires and wheels
load. The maximum load in­
cludes the number of passen­
gers that the vehicle is intend­
ed to carry ("seating capacity")
with an assumed weight of
150 lbs (68 kg) for each pas­
senger at a designated seating
position and the total weight of
any Luggage in the vehicle . If
you tow a trailer, the weight of
the trailer hitch and the tongue
weight of the loaded trailer
must be included as part of the
vehicle load .
The
Gr oss Axle Weight Rating
("GAWR") is the maximum load
that can be applied at each of
the vehicle's two axles.
The Gross Vehicle Weight Rat ­
ing and the Gross Axle Weight Rating are listed on the safety
compliance sticker label locat­
ed on the driver's side 8-pillar .
Your Audi has 4 seating posi ­
tions, 2 in the front and 2 in the rear for total seating capacity
of 4. In some vehicles there are
5 seating positions, 2 in the
front and 3 in the rear for total seating capacity of 5. Each seat­
ing position has a safety belt
¢ page 138, Safety belts.
The fact that there is an upper limit to your vehicle's Gross Ve­
hicle Weight Rating means that
the total weight of whatever is being carried in the vehicle (in ­
cluding the weight of a trailer
hitch and the tongue weight of
the loaded trailer) is limited .
The more passengers in the ve­ hicle or passengers who are
heavier than the standard
weights assumed mean that less weight can be carried as
luggage.
The tire pressure label on your
Audi also lists the maximum
combined weight of all of the
occupants and luggage or other
cargo that the vehicle can carry. For the Location of the label
¢ page 247, fig . 200 .
_& WARN ING -
Overloading a vehicle can
cause Loss of vehicle control,
a crash or other accident, se­
rious personal injury, and
even death.
-Carrying more weight than your vehicle was designed to carry will prevent the ve­
hicle from handling properly
~

and increase the risk of the loss of vehicle control.
-The brakes on a vehicle that
has been overloaded may
not be able to stop the vehi­
cle within a safe distance.
-Tires on a vehicle that has
been overloaded can fail
suddenly, including a blow­
out and sudden deflation,
causing loss of control and a
crash.
-Always make sure that the total load being transported - including the weight of a
trailer hitch and the tongue
weight of a loaded trailer - does not make the vehicle heavier than the vehicle's
Gross Vehicle Weight Rat­
ing .
Determining correct load
limit
Use the example below to cal­
culate the total weight of the
passengers and luggage or oth­
er things that you plan to trans­
port so that you can make sure
that your vehicle will not be
~ overloaded.
Tires and wheels 257
Steps for Determining
Correct Load Limit
1. Locate the statement "THE
COMBINED WEIGHT OF OC­
CUPANTS AND CARGO
SHOULD NEVER EXCEED XXX KG OR XXX LBS" on your ve­
hicle's placard (tire inflation
pressure label)
¢ page 247,
fig. 200.
2. Determine the combined
weight of the driver and pas­sengers that will be riding in
your vehicle.
3. Subtract the combined
weight of the driver and pas­
sengers from
"XXX" kilo­
grams or
"XXX" pounds
shown on the sticker
¢ page 247, fig. 200.
4. The resulting figure equals the available amount of car­go and luggage load capaci­
ty. For example, if the
"XXX"
amount equals 1400 lbs.
and there will be five 150 lbs. passengers in your vehi­
cle, the amount of available
cargo and luggage load ca­
pacity is 650 lbs. (1400-7 50
(5
X 150) = 650 lbs.)
5. Determine the combined
weight of luggage and cargo ""
•
•
'

258 Tires and wheels
being loaded on the vehicle.
That weight may not safely
exceed the available cargo
and luggage load capacity
calculated in Step 4.
6. If your vehicle will be towing
a trailer, load from your trail­
er will be transferred to your
vehicle. Consult this manual
to determine how this re­ duces the available cargo
and luggage load capacity of
your vehicle.
.,.Check the tire sidewall
(¢ page 260, fig. 204) to de­
termine the designated load
rating for a specific tire.
Tire service life
The service life of tires depends
on a lot of different things in­
cluding proper installation and
balancing, correct tire pressure
and driving style.
Fig. 202 Tire tread: tread wear indi­
cators (TWI)
Fig. 203 Rotating tires for more even
wear
Tread Wear Indicator (TWI)
The original tires on your vehi­
cle have
1/16 inch (1.6 mm)
high "wear indicators"
¢ fig. 202 running across the
tread. Depending on the make,
there will be six to eight of
them evenly placed around the
tire. Marks on the tire sidewall (for example "TWI" or other
symbols) indicate the positions
of the tread wear indicators.
Worn tires must be replaced. Different figures may apply in
other countries
¢ .&. .
Tire pressure
Incorrect tire pressure causes
premature wear and can cause
sudden tire blow-out. For this
reason, tire press ure must be
checked at least once a month
¢page 252.

264 Tires and whee ls
tires because they meet the
h ighest standards regarding
safety and driving characteris ­
tics when used correctly. Your
authorized Audi dealer w ill
g ladly provide you with more
information.
Tire ply composition and materials used
T he number of plies indicates
the number of layers of rubber­
coated fabric in the tire. In gen­
eral, the greater the number of
plies , the more weight a tire
can support . Tire manufactur­
ers also must indicate the ma­
ter ia ls in the tire, wh ich include
steel, nylon, polyester, and oth­
ers .
Maximum Load Rating
This number indicates the max­
imum load in kilograms and
pounds that can be carried by
the tire.
Tire quality grading for
treadwear, traction, and
temperature resistance
Tread wear, trac tion and tem­
perature grades
¢ page 266.
Ma ximum Permissible
Inflation Pressure
T his number is the greatest
amount of air pressure that should ever be put in the tire
under normal driv ing condi­
tions.
A WA RNING
-Using incorrect or unmatch­
ed tires and/ or wheels or improper tire and wheel
combinations can lead to loss of control , collision and
ser ious personal injury.
-Always use tires, rims and
wheel bolts that meet the
specifications of original
factory-installed tires or
other combinations that
have been specifically ap ­
proved by the vehicle manu­
facturer.
- Tires age even if they are
not being used and can fail
sudden ly, especially at high
speeds. Tires that a re more
than 6 years old can on ly be
used in an eme rgency and
then with special care and
at lower speeds.
-Never mount used tires on
your vehicle if you are no t

M N <( I.J "". rl I.O
"'
@ Tips
Check carefully to make sure the hook-up
is secure before moving the car up the flat­
bed truck ramp .
Vehicle transport
Whenever you hov e your vehicle transported,
be sure to note the following :
(D Note
Mount the tie-down chains/cables over the
running surface (circumference) of the
tires. Never secure the vehicle by the axle,
the suspension struts or the front or rear
towline eye . For technical reasons, the
pressure in the suspension struts may
change du ring the transport and this will
adve rsely affect vehicle handling.
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may onl y be li~ed at the lif ting
points illu stra ted.
Fi g. 2 29 Front l ift ing po int
Fig. 2 30 Rea r lifti ng poin t
:;:; N 0 6 ., a,
5 .. Read and heed WARNING Q ,&..
Emergenc y situ ation s 289
.. Activate the vehicle jack mode* in the MM I:
!CAR I function button > (C ar)* s ystem s con­
trol button>
S e rv ic ing & check s> Air su sp. :
jack m ode> On .
.. Locate lifting poin ts Q fig . 229 and
Q fig . 230 .
.. Adjust lifting arms of wo rkshop hoist or
floor jack to match veh icle lifting points.
.. Insert a rubber pad be tween the floor jack/
workshop hoist and the lift ing po in ts.
The vehicle jack mode* must be activated so
that the automat ic adjustment of the Adap­
tive Ai r Suspens ion* does not make it more
diffi cult to raise the vehicle with the floor
jack.
If yo u must lift your v ehi cle with a floor jack
t o wo rk und ern eath , be sure th e vehicle i s
s af ely s upported on s tands intended for thi s
purpo se.
Front lifting point
The lifting po int is located on the floor pan re­
inforcement abo ut at the same leve l as the
jac k mounting point
Q fig. 229. Do n ot lift
t h e ve hicle at th e verti cal sill reinforc em ent .
Re ar lifting point
The lifting point is located on the vert ical rein­
forcement of the lower sill for the on-boa rd
ja ck
c::> fig. 230 .
Lifting with vehicle j ack
Re fer to Q page 277 .
A WARNING
-To reduce the risk of ser ious injury and
veh icle damage .
- Always lift the veh icle only at the spe ­
cia l workshop hoist and floor jack lift
po ints illust rated
c::> fig . 229 and
c::> fig . 230.
- Failu re to lift the vehicle at these
po ints could cause the vehicle to tilt or
fall from a lift if there is a change in ve­
hicle weight distribution and balance .
This might happen, for example, when
-