-The longer one tire is used in one location on the vehicle,
the more it wears at certain points; therefore, we recom
mend that you follow the tire
manufacturer's suggested tire
rotation intervals.
-Vehicles with front-wheel drive experience more tread
wear on the front wheels com pared to all-wheel drive (quat
tro).
-Please rotate tires as shown
¢ fig. 171.
-Extra care must be taken when
rotating direction-specific
tires
Q page 2 74.
Wheel balancing
The wheels on new vehicles are balanced. However, various sit
uations during everyday driving
can cause them to become un
balanced, resulting in vibra
tions you can usually feel
through the steering wheel.
Unbalanced wheels must be re
balanced to avoid excessive
wear on steering, suspension
and tires. A wheel must also be
rebalanced when a new tire is
M N
~ installed. co ,...., \!) 1.1"1
M 1.1"1 ,....,
Tires and wheels 253
Incorrect wheel alignment
Incorrect wheel alignment can
cause excessive tire wear, impairing the safety of the vehi
cle. If tires show excessive
wear, have the wheel alignment checked by an authorized Audi
dealer or qualified workshop.
All-wheel drive
Vehicles with quattro must al
ways have tires of the same size, construction and tread
type. For details see
¢ page 193 .
.8, WARNING
Sudden tire failure can lead
to loss of control, a crash and serious personal injury!
-Never drive a vehicle when the tread on any tire is worn down to the wear indica
tors.
-Worn tires are a safety haz ard, they do not grip well on
wet roads and increase your risk of "hydroplaning" and
loss of control.
-Always keep chemicals that can cause tire damage, such
-
as grease, oil, gasoline and
brake fluid away from tires.
~
' •
•
' •
....,
N
0 > co
rl I.O
"' ....,
"' rl
-Support the vehicle securely with ap
propriate stands if work is to be per
formed underneath the vehicle;
otherw ise, there is a potential risk for
injury .
- To help prevent injury to yourself and
your passenge rs:
- Do not raise the vehicle until yo u are
sure the jack is secu rely engaged .
- Passenge rs must no t remai n in the ve
h icle when it is jacked up .
- Ma ke sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traff ic.
- Make sure ja ck position is correct, ad
jus t as necessary and then conti nue to
raise the jack .
- Changes i n tem pera ture or load can af
fect the height of the vehi cle.
(D Note
Do not lift the vehi cle by the s ill. Pos ition
the vehicle jac k only at the designated lift
ing points o n the sill. Othe rwise, your vehi
cle will be damaged .
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
F ig . 1 84 Chan gin g a w hee l: us ing t he sc rew driver han
dl e (w it h t he bla de removed) to t urn th e bolts
What do I d o now ? 273
Fig . 1 8 5 Changi ng a wheel : al ig nme nt p in in sid e th e
t op hole
After yo u have loosened all wheel bo lts and
raised the vehicle
off the ground, remove and
replace the wheel as follows :
Removing the wheel
.,. Use the he xag onal so cket in the scre wdriv
er handle
to comple tely remove the top
most whee l bolt and set it aside on a
clean
surface ¢ fig. 184.
.,. Screw the threaded end of the alignment
pin from the tool kit hand- tight into the
empty bolt hole
Q fig . 185.
.,. Then remove the other wheel bolts as de
scribed above .
.,. Take
off the whee l leaving the alignment pin
in the bo lt ho le
¢ (D .
Putting on the comp act spare wheel
.,. Lift the spare wheel and carefully slide it
over the alignment p in to g uide it in place
¢ (D .
.,. Use the hexagona l socket in the screwd river
h a ndle to screw in a nd tig hten all whee l
bolts
slightly .
.,. Remove the alignment pin and insert and
tighten the remaining whee l bolt slightly
like the rest .
.,. Turn the jack hand le counter-clockwise to
lower the veh icle until the jack is fully re
leased .
.,. Use the wheel bo lt wrench to tighten all
wheel bo lts firm ly
i=;, page 271. Tighten
them
c rosswise, from one bolt to the (ap
proximately) opposite one, to keep the
wheel cente red.
