Checking and Filling
-Before work is done on the electrical sys
tem, disconnect the negative ground cable .
- Before performing any work on the electri
cal system, switch off the engine and igni
tion as well as any electrical equipment. The
negative cable on the battery must be dis
connected . If you are just going to replace a
light bulb, then it is enough to switch off
the lights.
- Before disconnecting the battery, switch off
the ant i-theft alarm system! Otherwise you
will set off the alarm.
- When disconnecting the battery, first dis
connect the negative cable and then the
positive cable.
- Before reconnecting the battery, make sure
all electrical consumers are switched off. Re
connect the positive cable first and then the
negative cable. Never interchange the ca
bles -this could start a fire!
- Never charge a frozen or a thawed-out bat
tery. It could explode! If a battery has fro
zen, then it must be replaced. A discharged
battery can freeze over at 32°F (0°C) .
- Make sure the vent hose is always attached
to the opening on the side of the battery.
- Never use batteries which are damaged.
There is the danger of an explosion! Always
replace a damaged battery.
A WARNING
California Proposition 65 Warning:
- Battery posts, terminals and related acces
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive problems.
Wash hands after handling.
(D Note
- Do not disconnect the vehicle battery when
the ignition is switched on or when tile en
gine is running, otherwise, you will damage
electronic components in the electrical sys
tem.
- If your vehicle is going to stand for a long
period of time without being driven, protect
the battery from "freezing", otherwise it
198
will be damaged and will then have to be re
placed.
Battery charging
Starting the engine requires a well charged bat
tery.
Fig. 167 Eng ine compartment: Connectors for charger and
jumper cables
Always read and heed all WARNINGS below
¢
A and ¢ A in Working on the battery on
page 197.
.,. Turn off the ignition and all electrical consum
ers.
.,. Make sure the area is well ventilated when you
charge the battery.
.,. Open the engine hood
¢ page 187.
.,. Open the cover on the positive pole¢ fig. 167.
.,. Connect the charger connectors according to
the instruct ions to the
jump start bolts . (Bolts
under the cover= "positive", Bolts with hex
head = "negative").
.,. Only now plug the mains lead for the charging
equipment into the wall outlet and turn it on
¢ &, .
.,. Make sure the charging rate is not over
30 amps/14.8 Volt.
.,. When the battery is fully charged : T urn the
charging equipment off and remove the mains
lead from the wall outlet.
.,. Now remove the clamps for the charging equip -
ment .
.,. Close the cover on the positive pole.
.,. Close the hood¢
page 187.
A discharged battery can freeze at temperatures
of only 32 °F (0 °C). Allow a frozen battery to
thaw completely before attempting to charge it
Ill>
M N
0:: loo ,...., \!) 1.1'1
N 1.1'1 ,....,
q &.. However, we recommend not using a
thawed battery again because the battery casing
can be cracked due to ice formation and can leak
battery acid.
Batt ery chargi ng (Maximum cha rging rate of
30 amp s/14 .8 Volt )
When charging at
low voltages (e.g. with a trickl e
cha rger ), the battery cables do not have to be
d isconnected first. The battery caps shou ld
not
be opened when charg ing a battery.
It is not necessary to remove the battery from
the luggage compartment.
Fast charging th e battery (char ging rat e
above 14 .8 Vo lt s)
For technical reasons do not use a battery charg
er that uses voltage greater than 14.8 Volts to
charge your vehicle's battery.
A WARNING
Charging a battery can be dangerous.
- Always follow the operating instructions
provided by the battery charger manufactur
er when charging your battery.
- Never charge a frozen battery. It may ex
plode because of gas trapped in the ice. Al
low a frozen battery to thaw out first.
- Do not reuse batteries which were frozen.
The battery hous ing may have cracked and
weakened when the battery froze.
- Charge the battery in a well ventilated area.
Keep away from open flame or electrical
spark. Do not smoke. Hyd rogen gas generat
ed by t he battery is explos ive.
- To reduce the danger of explosion, never
co nnect or disconnect cha rger cables while
the cha rger is operating.
- Fast charg ing a battery is dangerous and
should only be attempted by a competent
tec hnician with the p roper equipment.
- Battery acid that may spill du ring charg ing
sho uld be washed off w ith a so lution of
wa rm w ater and baking soda to ne utralize
the acid .
Checking and Fillin g
(D Note
Never use a fast charger as a booster to start
the engine . This will ser iously damage sensi
tive electronic components, s uch as control
units, relays, radio, etc., as well as the battery
charger.
Battery replacement
The new battery must hove the some specifica
tions and dimensions as the original equipment
battery.
Intelligent energy management in your vehicle is
responsible for distributing the electrical energy
t h roughout your vehicle
q page 175. The intelli
gent energy management system w ill keep the
engine battery charged better then vehicles with
out this system. To make s ure the addit ional elec
t rical energy is ava ilab le once again afte r yo u
have changed the battery, we recommend that
you install batteries of the same type and man u
facture on ly (the same as those insta lled at the
t ime yo ur vehicle was delivered). Specifications
are listed on the battery hous ing. Your author
ized Audi dealer must code the battery in the en
ergy management system to enab le you to use
the e nergy management fu nctions correctly after
replacing the battery.
If it is not possib le to use a battery of this type,
the new battery must have the same capac ity,
voltage ( 12-volts), amperage, construction and
plug sealing.
When installing the battery, make sure the igni
t ion and all electr ica l consumers are turned off.
(D Note
Make sure the ventilat ion hose on the side of
the battery is connected, otherwise fumes or
battery acid can leak out.
@ For the sake of the environment
Because of the prob lem of proper disposal of
a battery, we recommend your authorized
Audi dealer change the battery for you. Bat
teries contain sulfur ic acid and lead and must
a lways be d isposed of properly in compliance ..,.
199
Emerg enc y s it uat ion s
Emergency situations
General
T his c hapt er is inte nded fo r tra ined e merg ency
c rews a nd worki ng p ers onn el w ho h ave the nec
e ssa ry tool s and equipm ent t o perf orm the se
op era tion s.
Starting by pushing or
towing
CD Note
Vehicl es with an automa tic tra nsmission
c annot be st arted by pushing or towing .
Starting with jumper
cables
If necessary, the engine con be started by con
necting it to the battery of another vehicle .
If the engine should fail to start because of a d is
charged or weak battery, the battery can be con
nected to the battery of
another vehicle, us ing a
p air of j umpe r cables to start the engine.
Jump er c abl es
Use only jumper cab les of sufficiently largec ross
sec tion
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use on ly jumper cables with
insulated term inal
clamps which are d istinctly mar ked:
plus (+ ) cabl e in most cases co lored re d
minu s(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, ac id, and gas.
Any of these can cause very ser ious or fatal in
jury . Fo llow the inst ruct ions be low for safe
hand Ling of your veh icle's battery.
- Always shield your eyes and avoid leaning
over the battery whenever possible.
- A discharged battery can freeze at tempera
tures just below 32 °F (0 °C). Before con
nect ing a jumper cab le, you must thaw the
228
frozen battery completely, otherwise it
could explode.
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immed iately.
- Improper use of a booster battery to start a
veh icle may cause an explosion.
- Vehicle batteries generate explosive gases .
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must al
so have a 12-Volt rat ing . The capacity (Ah)
of the booster battery should not be lower
than that of the discharged battery. Use of batter ies of different voltage or substantial
ly different "Ah" rating may cause an explo
sion and personal injury .
- Never charge a frozen battery . Gas trapped
in the ice may cause an explosion .
- Never charge or use a battery that has been
frozen . The battery case may have be weak
ened .
- Use of batter ies of different voltage or sub
stantially d ifferent capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery sho uld not be
lowe r than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS
qpoge 187.
CD Note
-App lying a higher voltage booster battery
wi ll cause expensive damage to sensitive
elec tronic components, such as control
units, re lays, radio, etc.
- T here must be no electrical contact between
the vehicles as otherwise cu rrent cou ld al
ready start to flow as soon as the positive
(+) termina ls are connected.
@ Tips
The discharged battery must be properly con-
nected to the vehicle's electrical system. .,.
"' N
0:: loo
rl I.O
"' N
"' rl
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negat ive post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negative g round cab le to the negative ground
post of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable clamps in
exactly the order described below!
Fig. 187 Engine compa rtment: Connectors for jumper ca
b les and c harger
Fig. 188 Ju m p sta rting with the battery of anot her veh icle :
@ boos te r ba ttery, @ discharged veh icle battery
The procedure described below for connecting
jumper cables is intended to provide a jump start
for your vehicle.
Vehicle with discharged battery :
.. Turn
off lights and accessories, move lever of
automatic transmission to N (Ne utra l) or P
(Park) and set parking brake.
Connect POSITIVE(+) to POSITIVE(+) (red)
.. Remove the cover above the jump start connec
t ion.
.. Open the cover on the posit ive pole ¢
fig. 187.
Emergency situations
1. Connect one end of the red positive cable on
the jump start bolt~
fig. 188 (D (Bolts un
der cover= "positive") of the vehicle to be
started @.
2. Connect the other end to the positive termi- nal@of the booster battery @.
Connect NEGATIVE (-) to NEGATIVE(-)
(black)
3. Connect one end of the black negative cable
to the negative terminal ® of the booster
battery @.
4 . Connect the other end to the jump start bolt
@ (Bolts with hex head= "negative") of the
vehicle to be started @.
Starting the engine .. Start the engine of the veh icle with the booster
battery @. Run the eng ine at a moderate
speed .
.. Start engine with discharged vehicle battery @
in the usual manner.
.. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seconds and then try again .
.. With engine running, remove jumper cables
from both vehicles in the exact
reverse order .
.. Close the cover on the positive pole.
The battery is vented to the outside to prevent
gases from entering the vehicle inter ior. Make
sure that the jumper clamps are well connected
with their
metal parts in full contact with the
batte ry terminals.
A WARNING
To avoid serious personal injury and damage
to the vehicle, heed all warnings and instruc
tions of the jumper cable manufacturer. If in
doubt, call for road service.
- Jumper cables must be long enough so that
the vehicles do not touch .
- When connecting jumper cables, make sure
that they cannot get caug ht in any moving
parts in the eng ine compartment.
- Do not bend over the batteries -danger of
chemi cal burns!
229
Emergency situation s
-The ba ttery ce ll lockin g screws must be
t ightened securely .
- Before you check anyt hing in the engine
compartment, always read and heed all
WARNINGS
c> page 187.
(D Note
Improper hook -u p of jumper cables can r uin
the generator .
- A lways connect POS ITIV E(+ ) to POS ITIV E
( + ), and NEGATIVE( -) to NEGATIVE( -)
gro und post of the battery manager control
unit .
- Check that a ll screw plugs o n the batte ry
ce lls are screwed in firmly . If not, tighten
pl ugs prior to connect ing clamp on negat ive
battery te rminal.
- Please note that the procedure for connect
i ng a jumper cable as desc ribed above ap
plies specifica lly to the case of yo ur vehicle
being jump started . W hen you a re g iving a
j u mp sta rt to another vehicl e, do
not co n
ne ct the negative ( -) cab le to the negative
( -) t erminal o n the di scharged battery @
c> fig. 18 8 . In stea d, secure ly co nn ect the
nega tive ( -) cab le to either a solid me tal
com ponent that is f irm ly bolted to the en
gine block o r to t he engine bloc k itself. I f
the battery that is being charged does not
vent to the outside , escap ing battery gas
could ignite and exp lode!
Towing with a tow truck
General hints
Y o ur Audi requires special handling for towing.
The fo llow ing information is to be used by com
mercia l tow truck operato rs who know how to op
erate their eq uipment safe ly .
- Never tow your Audi, towing will cause dam
age to the engine and transmiss ion.
- Never wrap the safety chains or winch cables
around the brake lines .
- To pre vent unnecessary damage, your Audi
must be transported with a flat bed truck.
230
- To load the vehicle on to the flat bed , use the
towing loop found in the vehicle tools and at·
tach to the front or rear anchorage
c> page 230 and c:>page 231.
A WARNING
A veh icle being towed is not safe f or passe n
gers . Never a llow anyone to ride in a ve hicle
be ing towed, fo r any reason .
Front towing loop
Do not install the front towing loop until it is
needed .
Fig. 18 9 Fro nt b um per: remov ing t he cove r cap
Fig. 190 Front b umper: sc rew ing in t he tow ing loop
The towing loo p fits in to the threade d hole locat
ed on the right side o f the front bum per and cov
e red by a small cover when not in use .
.,. Remove the tow ing loop fr om the vehicle tool
ki t
c> page 216.
... Take ho ld of the bot tom edge o f the cover cap
and pull it out of the bumpe r
9fig . 189 .
... Sc rew the tow ing loop t ightly into the threaded
hole as far as it will go
c> fig. 190 and t ighten it
with the wheel wrench . ..,.
"' N
0:: loo
rl I.O
"' N
"' rl
Technical data
Vehicle identification
F ig. 196 Ve hicle Identificat io n Number (VlN) plate: loca·
t io n on d river 's s id e dash pane l
XXXXX XX -X -XXXX XXX XX
CD+ ~t :1:: xxxxxxxx xx x xx xxx xxx
T VP /fffl XXX XXX
XX XXXXXXX XX X X xx
XXX KW XXX
®i ~:J·f lfils~~ XXXX XXX XXX
®-+ ~N:a=i~ l xxxx ; xxxx xxx ; xx
II.· AUSS, I OPTIONS
,__ __
EO A 7D5
2EH JOZ
3FC
FOA
TL6 3KA
lX W
7T6 CV 7
3L4 lSA
4UB 6XM 5SG
llB l AS
S MU 7Xl
9G3 0G7 0YH
8EH Ul A X 98
803 908 824
7K0 4X3
2 K2
4KC 3Y0 413
7GB
01 A
5R W
18A
OJF
QZ7
020
502
4G0
XX . X XX X XX X XXXX
Fig. 197 T he veh icle identi fica tion label: ins ide the l ug·
ga ge compart men t
Vehicle Identification Number (VlN )
The Veh icle Iden tifica tion Number is located in
d iffe rent p laces:
- under the w indshield on the dr iver's side
c> fig . 196.
-in the radio or in the MM I*: Select : I CARI func
t ion button
> V ehicle ID numb er (VIN ) or se·
Leet :
I CARI funct ion button > Car sy stem s* con
tro l bu tton >
Servicing & checks > VIN num
ber .
-on the vehicle identification la bel.
Technical d ata
Vehicle id entification label
T he veh icle identification label is lo cated in the
lu ggage compartment near the battery.
T he labe l c>
fig. 197 shows the fo llowing vehicle
da ta:
(D Vehicle Ident ificat ion Number (VIN)
@ Vehicle type, engine o utp ut, transmission
® Engine and transm iss ion code
@ Pa int number and interior
® Optional equipment numbers
T he information of the veh icle identification label
c a n a lso be fo und in you r W arranty
& Mai nte
nance booklet.
Safety compliance sticker
T he safety compliance sticker is you r assurance
that your new vehi cle complies w ith all applicable
Federa l Mo tor Vehi cle Safety Sta ndards which
were in effec t at the time the vehicle w as m anu
fac tured. Yo u can find this sticker on the door
jamb on the driver 's side. It shows the month and
year of production and the vehicle identification number of your vehicle (perforation) as we ll as
the Gross Veh icle Weight Rating (GVWR) and the
Gross Axle Weight Rating (GAWR).
H igh vo ltage warning lab el
T he hig h voltage warning label is located in the
engine compartment ne xt to the eng ine hood re
lease. The spark ign ition system complies with
the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a st icker on the door jamb
on the dr iver's side.
T he Gross Vehicle Weight Rat ing includes the
weight of the basic vehicle plus fu ll fuel tank, oil
and coolant, p lus maxim um load, which includes
passenger weigh t (150 lbs/68 kg per designated
seat ing pos ition) and luggage we ight
c> .&, . ..,,.
233
M N
0:: loo ,...., \!) 1.1"1
N 1.1"1 ,....,
B
Battery ..... .. ................ ..... . .
16
Battery location inside the luggage compart-
ment. ..... .. ................ ..... . 197
Charge level . . . . . . . . . . . . . . . . . . . . . . . . 17 5
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Energy management .... .. .. .. .. .. .. .
Important warnings when working on the
battery .. ... ............. ...... ... .
Jump starting ............ .. .. .. .... .
Replacing the battery ..... .. .. .. .. .. .
Working on the battery .... .. .. .. .. .. .
Before driving ................ ... ... . .
Belt tensioners ...................... .
Blended gasoline .......... .... .. .. .. .
Blower (automatic climate control) .. .. .. . .
Booster seats ................ ... .... .
Brake flu id 175
197
228
199 197
111
126
183
69
158
Changing the brake flu id . . . . . . . . . . . . . . 196
Checking the brake fluid level . . . . . . . . . . 195
Brake system Anti -lock braking system . . . . . . . . . . . . . . . 18
Brake fluid specifications for refill and re
placement . . . . . . . . . . . . . . . . . . . . . . . . . 196
Brake light defect ive . . . . . . . . . . . . . . . . . . 21
Brake power assist unit . . . . . . . . . . . . . . . 172
Brakes ..... .. ................ ..... . 172
Ceramic brakes.............. ... .... . 172
Electromechanical parking brake . . . . . . . . 75
Warning/indicator lights . . . . . . . . . . . . . . . 15
Worn brake pads symbol . . . . . . . . . . . . . . . 19
Braking Brake assist . . . . . . . . . . . . . . . . . . . . . . . . 169
Emergency braking function . . . . . . . . . . . . 77
brak ing guard . . . . . . . . . . . . . . . . . . . . . . . . . 88
Messages
Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . .
... ................ ... .... ..
Break-in period
Brake pads ............... ... ... ... .
Tires .... .. .......... · · · · · · · · · · · · · ·
Breaking in .. ............. .... .. .... . 95
95
172
177 177
New tires . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Index
C
California Proposition 65 Warning ... .. . .
Battery specific . ................. .. .
Capacities .. .. .. .. .... ...... ... .. .. . .
Engine oil ... .. . .. ............ .. .. . .
Care ... .... .... ................... . .
Cargo area 188
198
234 189
181
refer to Luggage compartment . . . . . . 62, 117
Catalytic converter . . . . . . . . . . . . . . . . . . . . 178
Center armrest . . . . . . . . . . . . . . . . . . . . . . . . 56
Central locking . . . . . . . . . . . . . . . . . . . . . . . . 30
Central locking switch . . . . . . . . . . . . . . . . . 34
Convenience key . . . . . . . . . . . . . . . . . . . . . . 33
Remote contro l key . . . . . . . . . . . . . . . . . . . 33
Ceram ic brake rotors
New brake pads . . . . . . . . . . . . . . . . . . . . . 172
Certification . . . . . . . . . . . . . . . . . . . . . . . . . 239
Changing engine oil . . . . . . . . . . . . . . . . . . . 192
Checking Engine coolant level. . . . . . . . . . . . . . . . . . 193
Child restraints
Danger of using child restraints in the front
seat.. .. .. .. .. .. ............... .. .. 129
Where can I get additional informat ion
about child restraints and their use? . . . . 167
Child restraint system anchors . . . . . . . . . . 163
Child safety . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Important safety instructions for using child
safety seats . . . . . . . . . . . . . . . . . . . . . . . . 153
Installing a child restraint using the LATCH
system ....... .. ..... ........... .. .
Lower anchorages ................ .. .
Mounting and releasing the anchorage
hook ..... .. .. .. .. ............... . .
Tether anchors
Tether straps .... ................ .. .
Child safety seats 164
164
164
165
165
Booster seats . . . . . . . . . . . . . . . . . . . . . . . 158
Convertib le child seats . . . . . . . . . . . . . . . 156
Danger of using child restraints in the front
seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
How do I properly install a child safety seat
in my vehicle? .... ................ ... 153
I nfant seats . . . . . . . . . . . . . . . . . . . . . . . . 155
LATCH system . . . . . . . . . . . . . . . . . . . . . . . 164
Safety instruc tions . . . . . . . . . . . . . . . . . . . 153
Unused safety belts on the rear seat 155
241
M N
0:: loo ,...., \!) 1.1'1
N 1.1'1 ,....,
Electromechanical parking brake
Emergency braking . . . . . . . . . . . . . . . . . . . 77
Indicator light . . . . . . . . . . . . . . . . . . . . . . . 7 5
Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Releasing and closing . . . . . . . . . . . . . . . . . 75
Starting assist . . . . . . . . . . . . . . . . . . . . . . . 76
Starting from rest . . . . . . . . . . . . . . . . . . . . 76
Warning/indicator lights . . . . . . . . . . . . . . . 16
Electronic differential lock
Warning/indicator lights . . . . . . . . . . . . . . . 18
Electronic Differential Lock . . . . . . . . . . . . . 169
E lect ronic different ial lock (EDL)
Warn ing/ indicator lights . . . . . . . . . . . . . . . 18
Electronic immobilizer . . . . . . . . . . . . . . . 12, 36
Electronic power control
(EPC) warning/indicator light . . . . . . . . . . . 20
Electronic stabilization control
Sport mode . . . . . . . . . . . . . . . . . . . . . . . . 170
Electro nic Stabilization Control . . . . . . . . . . 169
E lectronic Stabilization Control (ESC)
Warning/indicator lights . . . . . . . . . . . . . . . 18
Emergency actuation
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
I gnition key . . . . . . . . . . . . . . . . . . . . . . . . . 33
Panoram ic tilting sunroof . . . . . . . . . . . . . . 39
Sun shade (roof) . . . . . . . . . . . . . . . . . . . . . 39
Emergency braking . . . . . . . . . . . . . . . . . . . . . 77
Emergency flasher . . . . . . . . . . . . . . . . . . . . . 45
Warning/indicator lights . . . . . . . . . . . . . . . 22
Emergency key . . . . . . . . . . . . . . . . . . . . . . . . 31
Starting engine . . . . . . . . . . . . . . . . . . . . . . 72
E mergency operation
Emergency braking function (parking brake) .7.7
Emergency sta rting . . . . . . . . . . . . . . . . . . . 228
Energy management . . . . . . . . . . . . . . . . . . 17 5
Battery power . . . . . . . . . . . . . . . . . . . . . . . 16
Driver notification . . . . . . . . . . . . . . . . . . . . 16
E ng ine
Compartment. . . . . . . . . . . . . . . . . . . . . . . 189
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Starting . .. .... ............. .. .. . 71, 73
Starting with jumper cables . . . . . . . . . . . 228
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . 73, 74
Engine compartment . . . . . . . . . . . . . . . . . . 189
Safety instructions . . . . . . . . . . . . . . . . . . . 187
Working the engine compartment . . . . . . 187
Index
Engin e coolant
In dicato r light . . . . . . . . . . . . . . . . . . . . . . . 17
Engine coolant system . . . . . . . . . . . . . . . . . 192
Adding coolant. .. ............. .. .. .. 193
Checking coolant level . . . . . . . . . . . . . . . . 193
Checking the engine coo lant level. . . . . . . 193
Radiator fan . . . . . . . . . . . . . . . . . . . . . . . . 195
Engine coolant temperature
Temperature gauge . . . . . . . . . . . . . . . . . . . 10
Engine hood Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
How to release the hood . . . . . . . . . . . . . . 187
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Additives. . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Changing . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Check oil level . . . . . . . . . . . . . . . . . . . . . . 191
Consumption . . . . . . . . . . . . . . . . . . . . . . . 191
Indicator light . .. ............. .... 17 , 20
Oil consumpt ion . . . . . . . . . . . . . . . . . . . . . 190
Pressure malfunction . . . . . . . . . . . . . . . . . . 16
Sensor defective . . . . . . . . . . . . . . . . . . . . . . 20
Specification and viscosity . . . . . . . . . . . . . 189
temperature indicator . . . . . . . . . . . . . . . . . 26
Engine speed limitation . . . . . . . . . . . . . . . . . 20
E nvironment
Catalytic converter . . . . . . . . . . . . . . . . . . . 178
Disposing of your vehicle battery ....... 199
Driving at high speeds . . . . . . . . . . . . . . . . 179
Fuel ............................... 185
Leaks under your vehicle . . . . . . . . . . . . . . 187
Letting the vehicle stand and warm up . . . 179
Proper disposal of drained brake fluid . . . 196
Proper disposal of drained engine coolant 193
Proper disposal of drained engine oil 191,192
Recycling used engine oil.......... .. . . 191
Roof rack . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Unleaded fuel . . . . . . . . . . . . . . . . . . . . . . . 183
What should I do with an old battery? . . . 199
EPC
refer to Electronic power control . . . . . . . . 20
Event Data Recorder (EDR) . . . . . . . . . . . . . . 168
Expansion tank . . . . . . . . . . . . . . . . . . . . . . . 193
Exterior lighting . . . . . . . . . . . . . . . . . . . . . . . 43
243