2015 AUDI RS5 CABRIOLET wheel alignment

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
wear on steering, suspension and tires. A wheel must also be
rebalanced when a new tire is
installed.
Incorrect wheel alignment
Incorrect wheel alignment can
cause excessive tire wear, im­
pairing the safety of the vehi­
cle. If tires show excessive
wear, have the wheel alignment checked by an authorized Audi
dealer or qualified workshop.
All wheel drive
Vehicles with quattro must al­
ways have tires of the same
size, construction and tread
type. For details see
¢page 176.
A WARNING
Sudden tire failure can lead
to loss of control, a crash and serious personal injury!
-Never drive a vehicle when the tread on any tire is worn down to the wear indica­
tors.
-Worn tires are a safety haz­
ard, they do not grip well on
wet roads and increase your risk of "hydroplaning" and
loss of control.
Tires and wheels 229
-Always keep chemicals that can cause tire damage, such
as grease, oil, gasoline and
brake fluid away from tires.
-Tires age even if they are not being used and can fail
suddenly, especially at high speeds. Tires that are more
than 6 years old can only be used in an emergency and
then with special care and
at lower speeds.
-Never mount used tires on your vehicle if you are not sure of their "previous histo­
ry." Old used tires may have
been damaged even though
the damage cannot be seen
that can lead to sudden tire
failure and loss of vehicle
control.
•
•
'

24 2 What do I do n ow ?
What do I do now?
Vehicle tool kit
The tools ore stored underneath the floor
panel in the luggage comportment.
Fig. 188 Luggage compartment: tool kit
When you need access to the vehicle too l kit
or jack*, you will need to take out the cover.
The vehicle tool kit includes:
- Tire repair kit (Tire Mobility System)
- Plastic cl ip for removing wheel bo lt caps*
- Alignment p in fo r cha nging the whee l
- Screwdriver with reversible blade
- Tool for chang ing light bulbs
- Reversible bit (reversible Torx bit for chang-
ing light bu lbs)
- Rod for jack
- Jack *
- Lug wrench
- T owing eye
Some of the ve hicle it ems listed above a re
p rov ided on certain models on ly or are opt io n­
a l extras.
Before returning the jack * to its place, retract
the jack arm fully .
.&, WARNING
- Never use the screw driver hex head to
t igh ten whee l bolts, s in ce the bolts can­
not at tain t he necess ary tightening tor­
que i f yo u use the hex head, potentially
causing an accident .
- T he factory -supplied ja ck is intended on ­
ly for your vehicle model. Under no cir ­
c u mstances should it be used to
lift
heavy vehicles or othe r loads; yo u risk in­
juring yo urself .
- Never start the engine when the vehicle
is raised, wh ich could cause an acc ident.
- Support the vehicle securely wit h app ro­
priate stands if work is to be performed
unde rneath the vehicle; otherwise, there
is a potentia l risk for injury.
Tire repair
General and safety pointers
Tire repair is intended only for temporary,
short-term use.
F ig . 1 89 Tire damage for wh ic h the Tire Mob ility Sys­
tem is not suited
Your vehicle is equipped with a tire repa ir k it,
the
Tire Mobility System (TMS ).
In the event of a tire failure, the TMS is in the
luggage compartme nt under the floor. It con­
s ists of the tire sealant and an e lectric air
pump .
U sing
T MS , tire damage caused by foreign
bodies up to abo ut
0.16 inch (4 mm ) in diam­
eter can be sea led reliably.
T he foreign object must stay in the tire .
The t ire sealant must not be used:
- for cu ts or pun ctures in t he tire wh ich a re
larger than 0 .16 inch (4 mm)
¢ fig. 189 @
-for damage to the rim @
- if you have been driving with very low ti re
p ressures or tires wi th no air@
U sing the
TMS is described in the section
¢ page 243.

248 What do I do now?
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
Taking the wheel off/installing a wheel
Follow these instructions step-by-step for
changing the wheel.
Fig. 195 Changing a wheel: using the screwdrive r han·
dle (with t he bl ade removed) to turn the bolts
Fig. 196 Changing a wheel: a lignment pin insid e t he
to p hole
After you have loosened all wheel bolts and
raised the veh icle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.,. Remove the topmost wheel bolt completely
with the
he xa gonal socket in the screwdriv­
er handle (vehicle tool kit)
c> fig. 195 and
set it as ide on a
clean surface.
.,. Screw the threaded end of the
alignment
pin
from the tool kit hand-tig ht into the
empty bolt hole
<='>fig. 196.
.,. Then remove the other wheel bolts as de­
scribed above. .,.
Take off the wheel leaving the a lignment pin
in the bo lt hole
c::> (D .
Putting on the other wheel
.,. Push the whee l over the alignment pin.
.,. Screw on the wheel bolts and tighten them
slightly using the hexagonal socket .
.,. Remove the alignment pin and insert and
tighten the rema ining wheel bolt slightly
like the rest.
.,._ Turn the jack handle counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
.,. Use the wheel bolt wrench to tighten all
wheel bo lts firm ly
c::> page 246. Ti ghten
them
in a crisscross pattern, from one bolt
to the (approximately) opposite one, to keep
the wheel centered .
.,._ Perform the steps required after changing
the wheel
c::> page 245, After changing a
wheel.
The hexagonal socket makes it easier to re­
move the wheel bolts from the rim. Care
shou ld be taken when removing the reversible
blade.
(D Note
When removing or installing the wheel,
the rim cou ld hit the brake rotor/ceramic
brake rotor* and damage the rotor. Work
carefully and have a second person to help
you.
@ Tips
- When mounting tires w ith unidirectional
tread design
make sure the tread pat­
tern is po inted the right way
c::> page 249.
-The wheel bolts should be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel
and the hub. Remove all d irt from these
surfaces before remounting the wheel.
- Do not use the hexagonal socket in the
sc rewdriver handle to loosen or tighten
the whee l bolts.