2015 AUDI Q7 warning

M
"' 0 ..J ' "' rl
"' rl
Garage door opener (Homelink)
Description
Applies to vehicles: with garage door opener (Ho melink)
Fig. 53 Garage door opener: examples of using with
different systems
You can activate various systems such as ga­
rage doors, security systems and home light­
ing from inside your vehicle using the garage
door opener (Homelink) . There are three but­
tons for this in the vehicle headliner that can
be in used in place of up to three hand -held
transmitters.
To operate systems using the garage door
opener, the three buttons in the roof headlin­
er must be programmed first .
A WARNING
Make sure no people or objects are in the
immediate vicinity of the equipment when
using or programming the garage door
opener. People can be injured and objects
can be damaged i f they are caught in the
equipment.
(D Tips
- Fo r secu rit y reasons, we recommend that
you clear the programmed buttons be­
fo re se lling the vehicle.
- For additional informat io n about Home ­
Link, visit www.homelin k.com.
- Fo r Decla rat ion of Compliance to United
Sta tes FCC a nd Indus try Canada regula­
tions
¢ page 329.
Op enin g an d clos ing 57
Operation
Applies to vehicles: with garage door opener (Homelink)
111111 111111
-
Fig. 5 4 Headliner : control unit
Requirement: The buttons in the roof headlin­
er must be programmed¢
page 57 and the
vehicle must be with in range of the system,
such as the garage door opener.
.,. Press the button to open the garage door.
The LED@ blinks or turns on.
.,. Press the button again to close the garage
door .
(D Tips
To open or close the garage door, press the
button, but do not hold it for longer than
10 seconds or the garage door opener
module will switch to p rogramming mode.
Programming the buttons
Applies to vehicles: wit h garage door opener (Homelink)
Fig. 55 Distance between the bumper and the han d
trans mitter
Programming the button: Part 1 with the
control s
1. Switch the ignition on.
2 . Press and hold both outer buttons in the
roof headliner
c::> page 57, fig. 54 until the ~

light sensor checked as soon as possible at an
authorized Audi dealer or qualified workshop.
A WARNING
- Daytime running lights and automatic
headlights are only intended to assist
the driver. They do not relieve the driver
of his responsibility to check the head­
lights and to turn them on manually ac­
cording to the current light and visibility
conditions. For example, fog cannot be
detected by the light sensors*. So always
switch on the headlights
~D under these
weather conditions and when driving in
the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists. Always turn on
the headlights so that you can see ahead
and so that others can see your car from
the back.
- Please obey all laws when using the
lighting systems described here.
@ Tips
-With the switch in AUTO front fog lights
and rear fog lights cannot be turned on in addition.
- The light sensor for headlight control is
located in the rear view mirror mount.
You should therefore not apply any stick­
ers to the windshield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted ¢
page 61.
-When you remove your key from the igni­
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv­
er's door is open.
- In cool or damp weather, the inside of
the headlights, turn signals and tail
lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clear shortly after
M "' switching them on. This does not affect 0
~ the service life of the lighting.
rl I.O
"' rl
"' rl
Clear vision 61
-In the event of a light sensor malfunc­
tion, the driver is notified in the instru­
ment cluster display¢
page 35.
Adjusting exterior lighting
The functions are set in the MMI.
.,. Select: !CAR ! function button > Systems*
control button > Exterior lighting. Or
.,. Select:
I CAR I function button > Car systems*
control button > Vehicle settings > Exterior
light ing.
Coming home (Lights when leaving car),
Leaving home (Lights when unlocking car)
The coming home function illuminates the
area outside the vehicle when you turn the ig­
nition off and open the driver's door. Depend­
ing on vehicle equipment, the function can be
switched on and off or the length of ti me the lights remain on* can be adjusted .
The leaving home illuminates the area outside
the vehicle when you unlock the vehicle . This
function can be switched on and off .
The Coming home and Leaving home func­
tions only operate when it is dark and the light switch is in the
AUTO position.
Daytime running lights
USA models: The daytime running lights can
be turned on or off using this function.
Canada models: The function cannot be
turned
off. It is activated automatically each
time the ignition is turned on. This menu item is shown "greyed out" .
Front fog lights
Fig. 57 Instrument panel: light switch

64 Clear vision
Notes on the se feature s
- The turn signals only work with the ignition
tu rned on. The indicator lights
II or ii in
the instr ument cluster ¢
page 14 also b link .
- After you have turned a corner, the turn sig -
nal switches off a utomat ically.
- T he
high beam works only when the head­
lights are on. The indicator light
SI in the
instrument cluste r illuminates when the
high beams a re on.
- The
headlight flasher works on ly as long as
yo u hold the leve r - even if there are no
lights turned on . The ind icator light
SI in
the instrument cl uster illum inates when you
use the head light flasher.
A WARNING
Do not use the hig h beam o r headlight
flasher if you know that th ese cou ld blind
oncoming traffic.
Interior lights
Front interior lights
-
The interior ligh ts include reading lights for
bo th the driver and the front passenger .
Fig. 6 2 Headli ner: Fro nt inte rior/read ing lights
@ Interior lights
Press the switch ¢ fig. 62 in the correspond ­
ing position.
0 -Interior lights off
I - Inte rior lights on
If the switch is in the center position, the inte­
rior lighting is controlled automatica lly.
@ Reading lights
T o tur n a read ing light on/off, press the b ut­
ton
t!J .
Rear interior lights
There are reading lights in the rear for the
passengers .
Fig. 63 Head liner: Rear read ing lights
~
--
' ~ '-
Fig . 64 Head liner: Third row read ing light
.. Press one of the switches ~ to turn the
N .., N
.:,
~
::i N -.:,
~
right or left reading light on or off c::;, fig. 63.
For vehicles with thi rd row seating *, the lug ­
gage compartment light can be switched on
and off with the button -M-and used as a read­
ing light
c::;, fig. 64. The rear lid has to be
closed.
The lights in the luggage compartment and in
t h e rear lid switch on and off automatically
when the lid is opened and closed.
@ Tips
If the rear lid remains ope n longer than 10
minutes, the l uggage compartment lights
turn off automatically to prevent the vehi­
cle battery from disc harging .

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
the rain sensor is not activated until vehicle
speed is above 4 mph (6 km/h).
To reduce the sensitivity of the rain sensor,
the switch@ must be moved down. To in­
crease the sensitivity of the rain sensor, the
switch must be moved up.
The higher the sensitivity setting, the sooner
the windshield wipers react to moisture on
the windshield . Increased sensitivity is sig­
naled by the windshield w ipers making a sin­
gle pass over the windshield.
The rain sensor wiper intervals depend on the
sensitivity setting as well as vehicle speed .
During brief stops, wiper motion will adjust in
relation to the amount of rain on the wind­
shield.
A WARNING
- Wiper blades are crucial for safe driving!
Only when they are in good condition are
they able to clear the windows properly
to provide uncompromised visibility .
Worn or damaged wiper blades are a
safety hazard
i:::> page 69, Replacing
windshield wiper blades!
- The rain sensor is only designed to assist
and support the driver.
It remains entire­
ly the driver's responsibility to monitor
outside weather conditions and to man­
ually activate the wipers as soon as rain
or drizzle reduces visibility through the
windshield .
(D Note
In freezing or near freezing conditions:
- Always check that the wiper blades are
not frozen to the glass before you turn
the wipers on. Loosen a wiper blade
which is frozen in place before operating
the wipers to prevent damage to the
wiper blade or the wiper motor .
- Do not use the wipers to clear a frosted
window . Using the wipers as a conven­
ient ice scraper will destroy the wiper
blades .
Clear vision 67
-Prior to using a car wash, the w indshield
wiper system must be switched off (lever
in position 0). This helps to prevent unin­
tentional switching on and damage to
the windshield wiper system.
(1} Tips
- The windshield wipers are switched off
when the ignition is turned off. Activate
the windshield wipers after the ignition
is switched back on by moving the wind­
shield wiper lever to any position .
- Worn or dirty windshield wiper blades
cause smearing which can affect the op ­
eration of the rain sensor . Check the con­
dition of your windshield w iper blades
regularly.
- The rain sensor is part of the interval
wiping system. Turning off the ignition
will also deactivate the rain sensor. To re­ activate the sensor, switch off the inter ­
val wiping function, then switch it back
on again.
- Make sure the washer fluid reservoir in
the engine compartment is topped off
before going on a long trip. Look up
i:::> page 2 70 for checking and filling the
washer container.
Rear window wiper
T he wip er lever is also used to operate the
rear window wiper and the automa tic wiper/
washer func tion.
Fig. 69 Wipe r leve r: activat ing the re ar w indow wiper
and was her
The rear w indow wiper and the automatic wip­
er/washer functions a re activated as follows : ..,.

68 Clear vis ion
Int ermittent w iping
.. Push the w iper lever forward to the first po­
sition @~
fig. 69. The rear window wiper
will wipe the window approx. every four sec­ onds .
Automatic wiper /washer function
.. Push the w iper lever fo rward to the second
stop,
posi tion (!), and hold it there for as
l ong as you want the rear wiper/washer to
operate.
.. Re lease the lever aga in . the wiper wi ll keep
runn ing for approx. four seconds.
Switching interm ittent wip er action off
.. Pull the lever all the way back to the or iginal
position .
As soon as the reverse gea r is engaged and
the front wipe rs are turned on and operat ing
at the same time, the rear wipe r also turns on
automatically.
A WARNING
Wipe r blades are crucial for safe d riving!
On ly in good condition are they able to
clear the windows properly to provide un­
restricted visibility. Worn or frayed wipe r
blades are a safety hazard! ¢
page 69,
Replacing windshield wiper blades
CD Note
In freezing or near freezing condit ions:
- Always check that the wiper blades are
not frozen to the glass before you turn
the wiper on. Loosen a wiper blade which i s frozen in p lace before operating the
wipe r to prevent damage to the wiper
blade o r the wiper motor .
- Do not use the wiper to clear a frosted
window . U si ng the w ipers as a conven­
i ent ice sc raper will destroy the wiper
blades.
-
Headlight washer system
App lies to vehicles : wi th headlight washe r system
The headlight washer system cleans the
headlights.
.. Operate the w indshield wiper/washer sys­
tem ¢
page 66, fig. 68 ® with the head­
lights turned on by ho lding the lever for lon­
ger than one second .
The washer jets extend forward out of the
front bumper driven by water pressu re to
spray the fro nt headlights w ith water .
You should inspect the headlights regu larly
(for example whe n refueling) and clean off
any solid di rt or i nsects from the le nses .
To ensure the system wor ks proper ly in w inter,
keep the washer jets free of snow and remove
any ice using a de-icing spray.
Service position
The wiper blades can only be changed in the
service position .
.. If the wiper blades are not frozen to the
windshie ld, bring the windshie ld wiper lever
to the basic pos ition @¢
page 66, fig. 68.
.. Select: !CAR I function button> Systems *
control button> Windshield wipers > Serv ­
ic e po sition .
Or
.. Select:
!CARI function button> Car sy stems*
cont ro l butto n > Servicing & checks > Wip er
s ervi ce po sition .
-On -changing the windshield wipe r blades
can o nly be done if you b ring the wiper arms
t o the servi ce position. Yo u will a lso avoid
pa int damage to the hood when wor king on
t he wipe rs in this position .
-Off -the w indshie ld w ipers are moved to
t heir initia l posi tion again .
CD Note
Never ma ne uver you r vehicle with the
front windshie ld w iper arms raised s ince
t hey will automatically be moved bac k t o

M
"' 0 __,
"". rl I.O
"' rl
"' rl
their basic position above a speed of 3
mph (6 km/h) and can scratch the hood.
@ Tips
- You can also use the service pos ition, for
example, if you want to protect the
windshield from icing by using a cover.
- The service position automatica lly
switches to
Off when you operate the
windshield wiper lever, or speed exceeds
3 mph (6 km/h).
Cleaning windshield wiper blades
Clean the windshield wiper blades when they
begin to leave streaks . Use a soft cloth and
glass cleaner to clean the windsh ield wiper
b lades .
Front w ipe r
• Place the windshield wiper arms in the serv­
ice position . Refer to
c::> page 68 .
• Lift the w iper arm away from the front win ­
dow .
Rear wiper
• Lift the w iper arm away from the rear w in ­
dow.
A WARNING
Dirty w indshield w iper blades can impa ir
your view. This can lead to acc idents .
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear.
F ig. 70 Remov ing t he wiper b lades
-
Clear vi sion 69
Fig . 71 In stall ing wipe r blades
Removing a wiper blad e
• Bring the windshield wipers to the serv ice
position
c::> page 68 .
• Lift the wiper arm away from the w ind­
shield.
• Squee ze the plast ic b racket on the wind­
shie ld w iper arm together on both s ides @
c::> fig. 70.
• Turn the wiper b lade away from the wiper
arm.
• Lift the wiper b lade off in the d irection of
the arrow @.
Installing wip er blad e
• Place the new wipe r blade in the retaine r on
the wiper arm © c::>fig . 71.
• Swing the w iper blade in the direct ion of the
arrow @aga inst the wiper arm.
• Squeeze the corrugation on the wiper u ntil
you hear the bracket cl ick in the wiper arm.
• Place the wiper arm back against the w ind-
shield.
If the wiper blades begin to streak the wind­
shield, this cou ld be caused by residue left on
the w indshield by automatic car washes.
Fill the windshield washer container with a
special solut ion avai lable at your authorized
Audi dealer to remove the residue.
A WARNING
--
For your safety, you shou ld rep lace the
wiper b lades once or twi ce a yea r. See your
a uthori zed Audi dealer fo r repla cement
b la d es.
~

70 Clear vis ion
(D Note
- The w indshield wiper blades must on ly
b e replaced when in the service position
c:;, page 68! Otherwise, yo u risk damag­
i ng t he pa int on the hood or the wind­
sh ield wiper motor.
- To he lp prevent damage to the wiper sys­
tem, a lways l oosen blades which are fro­
zen to the windsh ield befo re operat ing
wipe rs.
- To he lp prevent damage to w iper blades,
do not use gasoline, ke rose ne, pa int
th inner, o r othe r so lvents on or nea r th e
wipe r blades .
- To he lp preven t damage to the wiper
arms or other components, do not at­
temp t to mo ve the wipers by hand .
(j) Tips
Commercial hot waxes applied by a uto­
mat ic car was hes affect the cleanab ility of
the w indshield .
Changing the rear wiper blade
Fig. 72 Rear w ind ow w ipe r Detac hing the rea r wipe r
b lad e
Removing the wiper blade
,.. Fold the w indshield w iper arm away from
t h e g lass .
,.. Grasp t he uppe r end o f the wiper arm with
on e hand and the metal clamp on the w iper
blade with the other
c:;, fig . 72.
,.. Hold the wiper arm in the d irect ion of the
arrow @and pull the wiper blade out of the
holder only in the direction of the arrow @.
Attaching the wiper blade
,.. Adj ust t he wiper b lade in the holder.
,.. Ho ld the upper end of the wipe r arm wi th
one hand .
,.. Press the wiper b lade into the ho lder with
your other hand.
.,. Fold the wiper arm back on to the wind­
shie ld.
A WARNING
For safety reasons, the w indshie ld w iper
bl ades should b e re placed once or tw ice a
yea r.
Mirrors
Adjusting the exterior mirrors
Fig. 7 3 Fo rwar d sect io n of d river' s ar mr est: power mir­
ro r con trols
Adju sting exterior mirrors
,.. Rotate the knob to the© position (driver 's
exterior m irror) or to the ® position (pas­
senger 's exterior m irror)
¢fig. 73 .
.,. Rotate the knob and the mirror so that you
have a clea r view to the rear .
Heated mirrors
,.. Rotate the knob to pos ition @.
Folding both exterior mirrors flat*
.,. Rota te the knob to po sition @.
-
Depend ing on the outside tempera ture, t he
mir ro r su rfaces are heated until the ig nitio n is
swi tched off -even i f the knob is no lo nger in
pos ition @.
You are we ll-advised to fold the exter ior mir-
ro rs in when maneuver ing in tight spaces o r .,..

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
when leaving the car parked close to other
vehicles.
Memory setting for the exterior mirro rs *
When the seat pos ition is saved in the memo­
r y, the position of the exte rior mirrors is saved
at t he same time~
page 76.
If the position of the passenger mirror is
changed whe n the vehicle is in reve rse gear
and the switch is i n the ® position, th is new
tilte d position will be a utomat ica lly saved to
the remote key when the vehicle is taken out
of reverse gear. To save, the rotary knob for
mirror ad justment must be in the ® position,
the selector lever must be in the P position
and the ign ition must be off . Th is will now be­
come the stored setting when the vehicle is
put in reverse gear again .
Tilting the passenger' s side e xterior
mirror (only with seat memory )
When you move the selector lever into R (Re­
ve rse), the mir ror on the front passenger's
door (knob tu rned to @
Q fig. 73) will tilt
slig htly downward. This make is easier for you
to see the curb w hen you are backing in to a
parking space.
The mirro r returns to its in itia l position as
soon as reve rse gear is disengaged and vehicle
speed is above abou t 9 mp h (1 5 km/h). The
mirror a lso retu rns to its initia l position if the
switch is moved to the driver's exterior mirror
© o r the ignit io n is switched off.
(D Note
-Cur ved (i.e. convex) mirr or surfaces in ­
crease your field of view. Remembe r th at
vehicles or other objects w ill appear
smaller and farther away than when
seen in a flat mirror. If yo u use this mir­
ror to est imate distances of following
vehicles when c hanging lanes, you could
estimate incorrectly and cause an acci­
dent.
- If the mir ro r hous ing is moved un inten­
tiona lly (for exampl e, while park ing your
vehicle), t hen you must first fo ld the mi r- Clear vi
sion 71
ror elect rically . Do not read just the mir­
ror housing ma nually . You cou ld damage
the motor which controls the m irror .
-If you wash the vehicle in a n automatic
car wash, you must fold the exter ior mir­
rors in to reduce the risk of damage to
the mirrors . Never fold power fo ld ing ex­
terior mirrors* by hand. Only fo ld them
in and o ut using the power controls.
(D Tips
If t here sho uld be a ma lf u nction in the
e lectrica l system, you can st ill adjust the
ex ter ior mirrors by press ing the edge of
the m irror.
Dimming the mirrors
Fig . 74 Auto matic dimming rearview mirror*
Manual anti-glare adjustment
.,. Move the small lever ( located on the bottom
edge of the mirror) to the rear .
Automatically dimming mirrors*
.,. To dim the rearview mi rror and both exterio r
m irrors* , pr ess the @ button . Th e d io d e @
turns on. The rearview and exterior mirrors *
dim a utomatically when light shines on
them, for examp le from headlights on ave­
hicle to the rear.
A WARNING ...
Elect ro lyte fluid can lea k from aut omatic
d imm ing mirro rs if the glass is b roken .
E lec trolyte fluid can irrit ate sk in, eyes and
res pirato ry sys tem.