2015 AUDI Q7 winter tires

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
will remain in effect until you turn off the igni­
tion, assum ing that you have not changed or
reset the setting.
The speed warning symbol. (USA models)/
• (Canada models) in the warning 1 display
appears when you exceed the maximum
speed . It goes out when the speed falls below
the stored maximum speed.
The speed warning symbo l wi ll also go out if
the speed exceeds the stored maximum speed
by more than about 25 mph (40 km/h) for at
least 10 seconds. The stored maximum speed
is deleted .
Setting speed warning 1 <=;>page 29.
Speed warn ing 2
Storing warn ing 2 is recommended if you al­
ways want to be reminded of a certa in speed ,
for example when you a re traveling in a coun­
try that has a general maximum speed limit,
or if you do not want to exceed a specified
speed for winter tires .
The speed warning 2 symbol, . (U SA mod ­
els)/ . (Canada models) appears in the dis­
p lay when you exceed the stored speed limit.
Unlike warning 1, it will not go out unti l the
ve hicle speed drops below the stored speed
limit.
Setting speed warning 2
r:!;> page 29.
@ Tips
Even though your vehicle is equipped with
a speed warning system, you should sti ll
watch the speedometer to make sure you
are not driving faster than the speed lim it.
Dri ver inform ation di spl ay 29
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the I CH ECKi
button .
Fig . 23 CHECK button in the instr umen t clus te r
Storing the ma ximum speed
.,. Dr ive at the desired maximum speed .
.,. Briefly p ress the
I CHECK I but to n c::> fig. 23.
Resetting the m aximum speed
.,. Dr ive the veh icle at a speed of at least
3 mph (5 km/h)
.,. Press the
I CHECK ! button for more than 2
seconds.
The speed warn ing symbol . (USA models)/
• (Canada mode ls) will appear briefly in the
display when you release the
! CH ECK I button
to indicate t hat the maximum speed has been
stored successf ully.
T he maximum speed rema ins stored until it is
changed by pressing the
! CH ECK I button again
briefly or until it is deleted by a lengthy push
o n the bu tton.
Speed warning 2: setting a speed limit
Warning threshold 2 is set, changed and de­
le ted in the MMI .
.,. Select:
I CAR I function button > Sys tem s*
contro l button > In strum ent clu ste r >
Spe ed warning .
Or
.,. Select: !CAR I function b utton > C ar sy ste m s*
cont ro l butto n > Driver a ssist > Speed w arn­
ing .
Warning threshold 2 can be set in the speed
range starting from 20 mph to 150 mph ..,.

M N
0 ...J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
(D Note
If there is an electronic malfunction, ser­
votronic
w ill still function like a conven­
tional power steer ing system, providing a
constant steer ing support force that is no
longer proportionate to the vehicle speed.
This is most noticeable when turning the
steer ing whee l at low speeds (for examp le
when parking), -more effo rt will be re­
qui red than usual.
- Be awa re of the different than usual
stee ring response and adjust your stee r­
i ng force accord ingly .
- Have the problem checked and set right
by an Aud i dealer as soon as possible .
(D Tips
-When the engine is runn ing, never hold
the steer ing whee l turned a ll the way to
the right or to the left for longer than 15
seconds. The power s teer ing p ump w ill
overheat the hydraulic fluid if you keep ho lding the steering whee l turned a ll the
way . This is likely to damage the power
steering system .
- If the power steer ing system should fai l
entirely, or if the engine is not running
(for example, while being towed), you
will still be ab le to steer the vehicle .
However,
considerably more effort will
be required to do so .
- If the power steering system should
have a leak, or is not functioning proper­
l y, contact your authorized Aud i dealer
i mmediately.
- The power steering system requires a
spec ially formulated hydraulic fluid . T he
power steer ing reservo ir is the one locat­
ed farthest to the rear on the left side o f
the engine compartment
~ page 258.
The correct fluid leve l in the reservoir is
important for proper functioning of the
power steer ing .
Int ellig ent technolog y 22 7
Driving with your
quattro
With all-wheel drive , all four wheels are driv­
en .
Gener al info rmation
With all-wheel drive, power is distributed to
all four wheels. This happens au toma tically
depending on your driving style and the road
cond it ions at the time . See also
~ page 223.
Winter t i res
When d riving in the winter, your vehicle with
a ll-wheel drive has an advan tage, even with
regular tires. In winter road conditions it may
be advisable to mount winter tires (or all -sea ­
son tires) for improved driveability and brak­
ing: these tires must be mounted on
a ll four
wh eels. See also ~ page 298, Winter tires.
Tire ch ains
Where tire chains are mandatory on certain
roads, this normally also applies to veh icles
with all-wheel drive~
page 299, Snow
chains .
Replacing whee ls/tire s
Vehicles with all-wheel drive must always
have tires of the same s ize . Also avoid tires
with different tread depths . For deta ils see
page ~
page 291, New tires and replacing
tires and wheels.
.8, WARNING
A lways adj ust yo ur dr iv ing to road and t ra f­
fic conditions . Do not let the extra sa fety
afforded by all-wheel drive tempt you into
taking extra risks.
- Altho ugh the a ll-wheel drive is very ef ­
fective, always remember that braking
capacity is limited by tire traction . You
should therefore not drive at excessive
speeds on icy or slippery road surfaces.
- On wet road surfaces, be careful not to
drive too fast because the front wheels
could begin to slide on top of the water
(aquaplaning). If th is should occur, you •
•

M N
0 ...J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Vehicl e ca re a nd cl eanin g 243
& WARNING
-Only wash the vehicle when the ignition
is off and follow the instructions from
the car wash operator to reduce the risk
of accidents.
- To reduce the risk of cuts, protect your­
self from sharp meta l components when
washing the underbody or the inside of
the wheel housings.
- After washing the vehicle, the braking ef­
fect may be delayed due to moisture on
the brake rotors or ice in the winter . The
brakes must be dried first with a few
careful brake applicat ions .
{[) Note
-If you wash the vehicle in an automatic
car wash, you must fold the exterior m ir­
rors in to reduce the r isk of damage to
the mirrors . Power folding exterior m ir­
ro rs* must only be folded in and out us­
i ng the power folding function.
- Compare the track of your vehicle w ith
the d istance between the gu ide ra ils of
the faci lity- there is a risk of damage to
the wheels and tires.
- Compare the height and width of you r
vehicle with the he ight and width of the
tunnel at the facility. -
To prevent paint damage, do not wash
the vehicle in direct sunlight.
- To reduce the r isk o f damage to the sur­
face, do not use insect removing spong­
es, kitchen sponges or similar items.
- Matte finish painted vehicle compo­
nents:
- To reduce the risk of damage to the
surface, do not use polishing agents or
ha rd wax .
- Never use car wash cycles that apply
protective wax.
It can destroy the
matte fin ish effect .
- Do not place any stickers o r magnet ic
signs on vehicle parts painted w ith
matte fin ish paint. The pai nt cou ld be
damaged when the stickers o r magnets
a re removed.
@ For the sake of the environment
Only wash the ve hicl e in facilities spe cially
designed for that purpose . This will red uce
the r is k of dirty water contam ina ted with
oil from entering the sewer system.
Cleaning and care information
When cle aning and caring for individua l vehi ­
cle components, refe r to the fo llowing tab les.
The information contained there is simply rec ­
ommendations. For questions or for compo -nents that are not listed,
re fer to an author­
ized Audi dealer or a qualified workshop . Also
follow the information fo und in¢.& .
Cle aning ex terio r
Component Situation Solution
Wipe r bla des
Dirty c:> page 69, Cleaning windshield wiper blades
H eadligh ts/ Dirty Soft sponge with a m ild soap solutiona >
tail lights
S ensors /
Dirty Sensors: soft cloth with a so lvent-free cleaning product
camera l enses Came ra lenses : soft cloth with an alcohol -free cleaning
solution
Snow/ice Hand brush/solvent-free de-icing spray
•
•

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-If you notice unusual vibra­
tion or if the vehicle pulls to one side when driving, al­
ways stop as soon as it is safe to do so and check the
wheels and tires for dam­ age.
(D Note
-Please note that summer
and winter tires are de­
signed for the conditions
that are typical in those sea­
sons. Audi recommends us­ing winter tires during the
winter months. Low tem­ peratures significantly de­
crease the elasticity of
summer tires, which affects
traction and braking ability.
Tires and wheels 273
If summer tires are used in
very cold temperatures, cracks can form on the tread
bars, resulting in perma­
nent tire damage that can
cause loud driving noise and unbalanced tires. Audi is not
responsible for this type of
damage.
-Burnished, polished or chromed rims must not be used in winter road condi­
tions. The surface of the
rims does not have suffi­
cient corrosion protection
for this and could be perma­
nently damaged by road salt
or similar substances.
•
•
'
Glossary of tire and loading terminology
Accessory weight
means the combined weight (in
excess of those standard items
which may be replaced) of auto­ matic transmission, power
steering, power brakes, power
windows, power seats, radio, and heater, to the extent that
these items are available as fac­
tory-installed equipment (whether installed or not).
Aspect ratio
means the ratio of the height to
the width of the tire in percent. Numbers of 55 or lower indi­
cate a low sidewall for im­
proved steering response and
better overall handling on dry
pavement.

276 Tires a nd whee ls
Recommended inflation Sidewall
pressure
means that portion of a tire be -
see
c:::> page 2 7 4, Cold tire infla-tween the tread and bead.
tion pressure.
Speed rating (letter code )
Reinforced tire
means the speed at which a tire
means a tire design to operate is designed to be driven for ex-
at higher loads and at higher tended periods of time. The rat-
inflation pressures than the ings range from 93 mph (150
corresponding standard tire .
km/h) to 186 mph (298 km/h)
Reinforced tires may be identi -
c:::> page 294. You may not find
fied as "XL", "xl", "EXTRA
this information on all tires be-
LOAD", or "RF" on the sidewall.
cause it is not required by law.
Rim The speed rating letter code,
means a metal support for a where applicable, is molded on
tire or a tire and tube assembly the tire sidewall and indicates
upon which the tire beads are the maximum permissible
road
seated . speeds
c:::> A in Winter tires on
Rim d
iameter
page 298.
means nominal diameter of the
T ir e pressure mon itoring
system
bead seat. If you change your means a system that detects
wheel size, you will have to pur-
chase new tires to match the when one or more of a vehicle's
new rim diameter . tires are underinflated and illu-
Rim
size de signation
m inates a low tire pressure
warning telltale.
means rim diameter and width.
Tread
R im width
means that portion of a tire
means nominal distance be- that comes into contact with
tween rim flanges. the road.
...

294 Tires and wheels
"DOT ... 2214 ... " means, for
example, that the tire was pro-
duced in the 22nd week of
2014.
Speed rating (letter code)
The speed rating letter code on
the wheels indicates the maxi -
mum permissible road speeds
c> & in Winter tires on
page 298.
P up to 93 mph (150 km/h)
Q up to 99 mph (158 km/h)
R up to
106 mph (170 km/h)
s up to 110 mph (180 km/h)
T up to
118 mph (190 km/h)
u up to 124 mph (200 km/h)
H up to 130 mph (210 km/h)
V up to 149 mph (240 km/h)1
)
z over 149 mph (240 km/h)1
)
W up to 168 mph (270 km/h)1
)
Y up to 186 mph (298 km/h)1
)
Your vehicle is normally factory
equ ipped with tires, which pas-
sess excellent driving character- istics and give your Audi opti-
mum driv ing comfort. An elec-
tron ic speed limiter
c> page 28
l) For t ires with a maximum speed ca­
pability ov er 149 mph (240 km/h) ,
tire manufacturers sometimes use
the letters "ZR."
will normally prevent your vehi-
cle from going faster than the
tire speed rating
c> & .
U.S. DOT Tire Identification
Number (TIN) and tire
manufacture date
This is the tire's "serial num-
ber". It begins with the Letters
"DOT" and indicates that the
tire meets all federal stand- ards. The next two numbers or letters indicate the plant where
it was manufactured, and the
last four numbers represent the
week and year of manufacture. For example, the numbers
2214 mean that the tire was
produced in the 22nd week of
2014. The other numbers are marketing codes that may or
may not be used by the tire
manufacturer. This information
is used to contact consumers if
a tire defect requires a recall.
Audi Original tire
Tires with the identification
"AO" or "RO" have been special-
ly matched with your Audi. We
...

296 Tires and wheels
sure of their "previous histo-
and sudden deflation and
ry." Old used tires may have loss of control.
been damaged even though -Temperature grades apply
the damage cannot be seen to tires that are properly in-
that can lead to sudden tire flated and not over or un-
failure and loss of vehicle
derinflated.
control. -For technical reasons it is
-All four wheels must be fit-
not always possible to use
ted with radial tires of the wheels from other vehicles -
same type, size (rolling cir- in some cases not even
cumference) and the same wheels from the same vehi-
tread pattern. Driving with cle model.
different tires reduces vehi- -If you install wheel trim
cle handling and can lead to
discs on the vehicle wheels,
a loss of control. make sure that the air flow
-If the spare tire is not the to the brakes is not blocked.
same as the tires that are Reduced airflow to the
mounted on the vehicle -for
brakes can them to over-
example with winter tires -
heat, increasing stopping
only use the spare tire for a distances and causing a col-
short period of time and lision.
drive with extra care. Refit -Run flat tires may only be
the normal road wheel as used on vehicles that were
soon as safely possible. equipped with them at the
-Never drive faster than the
factory. The vehicle must
maximum speed for which have a chassis designed for
the tires on your vehicle are run flat tires. Incorrect use rated because tires that are of run flat tires can lead to
driven faster than their rat-
vehicle damage or acci-
ed speed can fail suddenly. dents. Check with an au-
-Overloading tires cause heat thorized Audi dealer or tire build-up, sudden tire fail- specialist to see if your vehi-
ure, including a blowout cle can be equipped with
..

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
run flat tires. If run flat tires
are u sed , they must be in­
stalled on all four wheels. Mixing tire types is not per­
mitted.
(D Note
-For technical reasons, it is not generally possible to
use the wheel rims from
other vehicles. This can hold
true for wheels of the same
vehicle type.
- If the spare tire is different
from the tires that you have mounted on your vehicle
(for example winter tires or
wide profile tires), then use
the spare tire for a short pe­ riod of time only and drive
with extra care. Replace the
flat t ire with the tire match­
ing the others on your vehi­
cle as soon as possible.
- Never drive without the
valve stem cap. The valves
could get damaged .
@) For the sake of the environment
Dispose of old tires in accord­
ance with the local require­ ments.
Tires and wheels
Uniform tire quality grading
- Tread wea r
- Traction AA A B C
- Temperature AB C
Quality g rades ca n be foun d where applicab le
on the t ire s ide wall between t read sho ulder
and maximum section width
c> page 291,
fig. 254 .
For example : Tread wear 200, Traction AA,
Temperat ure A .
All passenge r ca r tir es must con form to Feder ­
a l Safety Requ irements in add ition to these
grades.
Tread wear
T he tread wear g rade is a c omp arati ve rati ng
based on the wear ra te of the tire when tes te d
u nder con tro lled conditions o n a specifie d
government test course .
F o r ex ample , a tire gr aded 1S 0 wo uld wear
one a nd one h alf ( 11/ 2) times as well on the
governmen t course as a ti re g raded 100 .
T he re lative perfo rman ce of tires depe nds
up on the actu al c ondition s of the ir u se, how ­
ever, and m ay depa rt s ignificantly from t he
no rm due to va ria tions i n driving ha bits, se rv ­
ice p ractices and differences in road character­
istics and cl imate.
Traction
T he trac tio n gr ad es, from hig hest to lowes t,
a re AA, A, Ban d
C. Those g rades represe nt the
ti re 's ability to stop on wet pavement as
measured u nder cont rolled conditions on
specified government test surfaces of aspha lt
and concrete. A t ire mar ked C may have poor
traction performance
c> ,&. .
Temperature
The temperature gr ades are A (the highest),
B, and C, represent in g the tire's resistance to
the generation of heat and its ab ility to d issi­
pate heat when tested un der controlled condi­
tions on a specif ied indoo r labo rato ry test
whee l.
297
•
•