2015 AUDI Q7 flat tire

286 Tires and wheels
build-up, sudden tire failure
and loss of control.
-If the tire pressure is too low or too high, the tires
will wear prematurely and
the vehicle will not handle
well.
-If the tire is not flat and you
do not have to change a
wheel immediately, drive at reduced speed to the near­
est service station to check
the tire pressure and add air
as required.
(D Note
Driving without valve stem
caps can cause damage to
the tire valves. To prevent
this, always make sure that
factory installed valve stem caps on all wheels are secure­
ly mounted on the valve .
@ For the sake of the environment
Underinflated tires will also
increase the fuel consump­
tion .
Tires and vehicle load limits
There are limits to the amount
of load or weight that any vehi­
cle and any tire can carry. Ave­
hicle that is overloaded will not handle well and is more diffi­
cult to stop. Overloading can not only lead to loss of vehicle
control, but can also damage important parts of the vehicle
and can lead to sudden tire fail­
ure, including a blowout and
sudden deflation that can cause
the vehicle to crash .
Your safety and that of your passengers also depends on
making sure that load limits are
not exceeded. Vehicle load in­
cludes everybody and every­
thing in and on the vehicle.
These load limits are technical­
ly referred to as the vehicle's
Gross Vehicle Weight Rating
("GVWR") .
The "GVWR " includes the
weight of the basic vehicle, all
factory installed accessories, a
full tank of fuel, oil, coolant
and other fluids plus maximum load. The maximum load in­
cludes the number of passen­
gers that the vehicle is intend ­
ed to carry ("seating capacity")
with an assumed weight of 150 lbs (68 kg) for each pas­
senger at a designated seating
position and the total weight of
any luggage in the vehicle. If ""

288 Tires and whee ls
- The brakes on a vehicle that
has been overloaded may
not be able to stop the vehi­
cle within a safe distance.
-Tires on a vehicle that has been overloaded can fail
suddenly, including a blow­
out and sudden deflation,
causing loss of control and a
crash.
-Always make sure that the total load being transported
- including the weight of a
trailer hitch and the tongue
weight of a loaded trailer -
does not make the vehicle
heavier than the vehicle's
Gross Vehicle Weight Rat­
ing.
Determining correct load
limit
Use the example below to cal­
culate the total weight of the
passengers and luggage or oth­
er things that you plan to trans­
port so that you can make sure
that your vehicle will not be
overloaded.
Steps for Determining Correct Load Limit
1 . Locate the statement "THE
COMBINED WEIGH T OF OC­
CUPANTS AND CARGO
SHOULD NEVER EXCEED XXX KG OR XXX LBS"on your vehi­
cle's placard (tire inflation
pressure label)
~ page 2 78,
fig . 250 .
2. Determine the combined
weight of the driver and pas­
sengers that will be riding in
your vehicle .
3 . Subtract the combined
weight of the driver and pas­
sengers from
"XXX" kilo­
grams or
"XXX" pounds
shown on the sticker
~ page 278, fig. 250.
4. The resulting figure equals
the available amount of car­go and luggage load capaci­
ty. For example, if the
"XXX"
amount equals 1400 lbs .
and there will be five 150 lbs. passengers in your vehi­
cle, the amount of available
cargo and luggage load ca­ pacity is 650 lbs. (1400 -750
(5
X 150) = 650 lbs.)
5. Determine the combined weight of luggage and cargo .,..

292 Tires and whee ls
No . Description
® Load index and speed rat-
ing
(J) U .S. DOT tire identifica-
tion number
® Audi Original tire
® Sever snow conditions
@ Tire ply composition and
materials used
@ Maximum load rating
@ Treadwear, traction and
temperature grades
@ Maximum permissible in-
flation pressure
The tires and rims are essential
parts of the vehicle's design .
The tires and rims approved by
Audi are specially matched to
the characteristics of the vehi­
cle and can make a major con­
tribution to good road holding and safe handling when in good
condition and properly inflated
¢ ,&..
We recommend that all work
on tires and wheels be per­
formed by an authorized Audi
dealer. They are familiar with
recommended p rocedures and
have the necessary special too ls
and spare parts as well as the proper facilities for disposing of
the old ti res.
Autho rized Audi dealers have
the necessary information
about technical requirements
for installing or changing tires
and rims .
Replacing tires and wheels
Tires sho uld be replaced at
least in pairs and not individu­
ally (for example both front
tires or both rear tires togeth­
er).
B e sure to read and heed the in ­
formation to the tire pressure
monitoring system
c::> page 301.
Always buy replacement radial
tires that have the same specifi­cations as the tires approved
for your vehicle by Audi. Re­
placeme nt tires m ust always
have the same load rating spec­
ification as the orig inal equip­
ment or approved optional tires
listed in the table c::>page
278.
Audi-approved spec ificat io n
tires are specially matched to
your vehicle and its load limits ,
and can contribute to the im- portant roadholding, driving .,.

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
recommend using only these
tires because they meet the highest standards regarding
safety and driving characteris­
tics when used correctly. Your
authorized Audi dealer will
gladly provide you with more
information.
Tire ply composition and materials used
The number of plies indicates
the number of layers of rubber­
coated fabric in the tire. In gen­
eral, the greater the number of plies, the more weight a tire
can support. Tire manufactur­
ers also must indicate the ma­
terials in the tire, which include steel, nylon, polyester, and oth­
ers .
Maximum Load Rating
This number indicates the max­
imum load in kilograms and
pounds that can be carried by
the tire.
Tire quality grading for
treadwear, traction, and
temperature resistance
Tread wear , traction and tem­
perature grades ¢
page 297.
Tires and wheels 295
Maximum Permissible
Inflation Pressure
This number is the greatest
amount of air pressure that
should ever be put in the tire under normal driving condi­
tions.
A WARNING
- Using incorrect or unmatch­
ed tires and/ or wheels or
improper tire and wheel
combinations can lead to
loss of control, collision and
serious personal injury.
-Always use tires, rims and wheel bolts that meet the specifications of original
factory-installed tires or
other combinations that have been specifically ap­
proved by the vehicle manu­
facturer.
-Tires age even if they are not being used and can fail
suddenly, especially at high speeds. Tires that are more
than 6 years old can only be
used in an emergency and
then with special care and at lower speeds.
-Never mount used tires on your vehicle if you are not
•
•
'

296 Tires and wheels
sure of their "previous histo-
and sudden deflation and
ry." Old used tires may have loss of control.
been damaged even though -Temperature grades apply
the damage cannot be seen to tires that are properly in-
that can lead to sudden tire flated and not over or un-
failure and loss of vehicle
derinflated.
control. -For technical reasons it is
-All four wheels must be fit-
not always possible to use
ted with radial tires of the wheels from other vehicles -
same type, size (rolling cir- in some cases not even
cumference) and the same wheels from the same vehi-
tread pattern. Driving with cle model.
different tires reduces vehi- -If you install wheel trim
cle handling and can lead to
discs on the vehicle wheels,
a loss of control. make sure that the air flow
-If the spare tire is not the to the brakes is not blocked.
same as the tires that are Reduced airflow to the
mounted on the vehicle -for
brakes can them to over-
example with winter tires -
heat, increasing stopping
only use the spare tire for a distances and causing a col-
short period of time and lision.
drive with extra care. Refit -Run flat tires may only be
the normal road wheel as used on vehicles that were
soon as safely possible. equipped with them at the
-Never drive faster than the
factory. The vehicle must
maximum speed for which have a chassis designed for
the tires on your vehicle are run flat tires. Incorrect use rated because tires that are of run flat tires can lead to
driven faster than their rat-
vehicle damage or acci-
ed speed can fail suddenly. dents. Check with an au-
-Overloading tires cause heat thorized Audi dealer or tire build-up, sudden tire fail- specialist to see if your vehi-
ure, including a blowout cle can be equipped with
..

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
run flat tires. If run flat tires
are u sed , they must be in­
stalled on all four wheels. Mixing tire types is not per­
mitted.
(D Note
-For technical reasons, it is not generally possible to
use the wheel rims from
other vehicles. This can hold
true for wheels of the same
vehicle type.
- If the spare tire is different
from the tires that you have mounted on your vehicle
(for example winter tires or
wide profile tires), then use
the spare tire for a short pe­ riod of time only and drive
with extra care. Replace the
flat t ire with the tire match­
ing the others on your vehi­
cle as soon as possible.
- Never drive without the
valve stem cap. The valves
could get damaged .
@) For the sake of the environment
Dispose of old tires in accord­
ance with the local require­ ments.
Tires and wheels
Uniform tire quality grading
- Tread wea r
- Traction AA A B C
- Temperature AB C
Quality g rades ca n be foun d where applicab le
on the t ire s ide wall between t read sho ulder
and maximum section width
c> page 291,
fig. 254 .
For example : Tread wear 200, Traction AA,
Temperat ure A .
All passenge r ca r tir es must con form to Feder ­
a l Safety Requ irements in add ition to these
grades.
Tread wear
T he tread wear g rade is a c omp arati ve rati ng
based on the wear ra te of the tire when tes te d
u nder con tro lled conditions o n a specifie d
government test course .
F o r ex ample , a tire gr aded 1S 0 wo uld wear
one a nd one h alf ( 11/ 2) times as well on the
governmen t course as a ti re g raded 100 .
T he re lative perfo rman ce of tires depe nds
up on the actu al c ondition s of the ir u se, how ­
ever, and m ay depa rt s ignificantly from t he
no rm due to va ria tions i n driving ha bits, se rv ­
ice p ractices and differences in road character­
istics and cl imate.
Traction
T he trac tio n gr ad es, from hig hest to lowes t,
a re AA, A, Ban d
C. Those g rades represe nt the
ti re 's ability to stop on wet pavement as
measured u nder cont rolled conditions on
specified government test surfaces of aspha lt
and concrete. A t ire mar ked C may have poor
traction performance
c> ,&. .
Temperature
The temperature gr ades are A (the highest),
B, and C, represent in g the tire's resistance to
the generation of heat and its ab ility to d issi­
pate heat when tested un der controlled condi­
tions on a specif ied indoo r labo rato ry test
whee l.
297
•
•

298 Tires and wheels
Sustained high temperature can cause the
materia l of the tire to degenerate and reduce
tire life, and excessive temperature can lead
to sudden tire failure<=>,& .
The grade C corresponds to a level of perform­
ance which a ll passenger car tires must meet
under the Federa l Motor Veh icle Safety Stand ­
ard No.
109. Grades Band A represent higher
levels of performance on the laboratory test
wheel than the minimum required by law.
A WARNING
The traction grade assigned to this t ire is
based on stra ight-ahead braking traction
tests, and does not include acceleration,
cornering, hydroplanin g or peak traction
characteristics.
A WARNING ,.,.____
The temperature grade for this tire is es­
tablished for a tire that is properly inflated
and not overloaded. Excessive speed, un­
derinflation, or excessive loading, either
separately or in combination, can cause heat buildup and possible tire fa ilure.
Winter tires
Winter tires can improve vehicle handling on
snow and ice. At temperatures below 45 °F
(7 °C) we recommend changing to winter
tires .
In some heavy snow areas, loca l governments
may require true winter or "snow" tires, those
with very deeply cut tread. These t ires should
only be used in pairs and be installed on all
four wheels. Make sure you purchase snow
tires that are the same size and construct ion
type as the other tires on your ve hicle.
Your veh icle is equipped with all -wheel drive,
this will improve traction during w inter driv­
i ng, even with the standard tires. However, we
strongly recommend that you always equip all
four whee ls on your veh icle w ith correctly fit­
ted winter ti res or all-season tires, when win­
ter road conditions are expected. This a lso im- proves the vehicle's
braking performance and
reduces stopping distances.
Summer tires provide less gr ip on ice and
snow.
Winter tires (snow tires) must always be fitted
on all four wheels.
Ask your authorized Audi dealer or qualified
workshop for perm itted
winter tire sizes . Use
only rad ial winter t ires .
Winter tires lose their effectiveness when the
tread is worn down to a depth of
0.157 inch
(4 mm).
Only drive w ith w inter t ires under winter con ­
ditions. Summer t ires handle better when
there is no snow or ice on the roads and the
temperature is above 45 °F (7 °() .
If you have a flat tire, see notes on spare
wheel<=>
page 291 .
Please always remember that winter tires may
have a lower speed rating than the tires origi­
nally installed on your vehicle at the time it
was manufactured. Please see
<=>page 294,
Speed rating (letter code)
for a listing of the
speed rating letter codes and the maximum
speed at which the tires can be driven .
The speed rating letter code (<=>
page 2 76) is
on the side wall of the t ire
c> page 291.
A WARNING ,.___
Winter tires have maximum speed limits
that may be lower than your vehicle's max­
imum speed. Always know the maximum
speed before driv in g off. Never drive faster
than the speed permitted for your specific
winter tires. This wi ll cause damage to the
tires leading to an accident and serious
personal injury to you and your passen­
gers.
A WARNING
'----
Driving faster than the maximum speed
for which the winter tires on your vehicle were designed can cause t ire failure in­
cluding a blowout and sudden deflation,

300 Tires and wheels
securely and that the brake system functions
correctly .
I n certain circumstances, you may not use
wheel bolts from a different vehicle -even if it
is the same model
¢ page 328.
A WARNING
Improperly tightened or maintained wheel
bolts can become loose causing loss of
control, a collision and serious personal in­
jury.
- Always keep the wheel bolts and the
threads in the wheel hubs clean so the
wheel bolts can turn easily and be prop­
erly tightened.
- Never grease or oil the wheel bolts and
the threads in the wheel hubs. They can
become loose while driving if greased or
oiled, even if tightened to the specified
torque.
- Only use wheel bolts that belong to the
rim being installed.
- Never use different wheels bolts on your
vehicle .
-Always maintain the correct tighten ing
torque for the wheel bolts to reduce the
risk of a wheel loss.
If the tightening tor­
que of the wheel bolts is too low, they
can loos en and come out when the vehi­
cle is moving .
If the tightening torque is
too high, the whee l bolts and threads
can be damaged and the wheel can be­
come loose.
{[) Note
The specified torq ue for the wheel bolts is
120 ft lb (160 Nm) with a tolerance of
± 7,4 ft lb(± 10 Nm). Torque whee l bolts
diagonally. After changing a whee l, the
torque must be checked as soon as possi­
ble with a torque wrench -preferably by an
author ized Audi dealer or qualified work­
shop.
Low aspect ratio tires
Your Audi is factory-equipped w ith low aspect
ratio tires. These tires have been thoroughly
tested and been se lected specifically for your
model for their superb performance, road feel
and handling under a variety of driving condi­
t ions . Ask your authorized Audi dealer for
more details.
The low aspect ratio of these tires is indicated
by a numera l of
55 or less in the tire's size
designation. The numera l represents the ratio
of the tire's sidewall height in relation to its
tread width expressed in percentage. Conven­
t iona l tires have a he ight/w idth ratio of 60 or
more .
The performance of low-aspect-ratio tires is
particularly sensitive to improper inflation
pressure. It is therefore important that low
aspect ratio tires are inflated to the specified
pressure and that the inflation pressure is
regularly checked and maintained. Tire pres­
sures should be checked at least once a
month and always before a long trip
¢ page 282, Checking tire pressure .
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damaged more
easily by impact with potholes, curbs, gullies
or ridges on the road, particularly if the tire is
underinflated .
In order to minimize the occurrence of impact
damage to the tires of your vehicle, we recom­
mend that you observe the following precau­
tions:
- Always maintain recommended inflation
pressures. Check your tire pressure every
2,000 miles (3,000 km) and add air if neces­
sary .
- Drive carefully on roads with potholes, deep
gullies or ridges. The impact from dr iving
through or over such obstacles can damage
your tires. Impact with a curb may also cause damage to your tires .
- After any impact, immed iately inspect your
tires or have them inspected by the nearest
II>