2015 AUDI Q7 warning light

16 Instrum ent s and w arn ing /indic ato r light s
;;./~ Electronic Stabilization Control
(ESC)
This warning/indicator light monitors the
Electronic Stabilization Control.
If th€ JjJ indicator light blinks wh ile driving,
the ESC or ASR (Ant i-S lip Regulation) is active­
l y regulating.
If the
DJ indicator light turns on, the system
has sw itched the ESC off . In this case, you can
switch the ignition off and then on to switch
the ESC on again. The indicator light turns off
when the system is functioning fully.
If the
II indicator light turns on, ESC was re·
stricted using the
I B OFF ! button~ page 223 .
Stabilization con trol (E SC/A BS): Fault! See
o wn er's manu al
If th€ J.i) indicator light and the ABS indicator
light
ml (USA models) ; IIJ (Canada models)
turn on and the message appears, the ABS or
electronic differential lock is malfunction ing .
This also causes the ESC to malfunct ion . The
brakes st ill function with the ir normal power,
but ABS is not act ive.
Drive to your authorized Aud i dealer or quali­
fied workshop immediately to have the mal·
function corrected.
A WARNING
If the 1111 (USA models) . (Canada
mode ls) brake system ind icator light turns
on togethe r with the ABS and ESC indica­
tor lights, the ABS/ESC regulating function
may have failed . Functions that stabilize
the vehicle are no longer avai lab le. This
could cause the vehicle to swerve and in·
crease the risk of sliding. Dr ive carefully to
the nearest authorized Aud i dea ler or oth­
er qua lified workshop and have the mal·
function corrected.
(D Tips
For additional information on ESC and
ABS, refer to
c:> page 223.
tli1 ! !r Safety systems
T he . (USA models)/ . (Canada mode ls)
i ndica tor light monito rs the safety systems
(e.g . ai rbags, pretensioners) and illuminates
for a few seconds each time you switch the ig­
nition on.
If the . (USA models)/ . (Canada models)
indicator light does not go out, or if it illumi­
nates while you are driving, or if it starts to
blink, then there is a malfunction somewhere
in the system. If the light does not illuminate
when you switch the ign ition on, th is also
means there is a malfunct ion.
A WARNING "'--
If you have a malfunction in the safety sys-
tems, contact your a uthorized Audi dea ler
i mmediately. Otherwise the safety sys­
tems may not work properly in an acc i­
dent.
¢¢ Turn signal s
The indicator light blinks when you use either
turn signal.
Whenever you use the left B or the right Ill
turn s ignal, the indicator light blinks . When
you use the emergency flashe rs, both indica­
tor lights flash .
If one of the turn signal light bulbs burn out,
the turn signal will blink twice as fast as nor· mal.
This does not apply, however, in towing mode.
The ind icator light does not flash if a turn sig·
nal is out on the tra iler or the towing veh icle .
Additional information on the turn s ignals
~page 63.

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Instrument s and warnin g/indic ator ligh ts 17
¢1.~ Trailer turn signal assembly
Appl ies to vehicles: with towing hitch
The indicator light also blinks if the turn sig­
nal is operated when towing a trailer .
The indicator light. blinks when the turn
signal is used, if a trailer has been properly
connected to the vehicle.
If one of the turn signal bulbs on the trai ler is
burned out or defective, the indicator light
will not blink when you use the turn signals.
{!) Tips
For vehicles with a factory installed towing
hitch or a trailer h itch that was installed
later according to factory specifications,
the trailer tu rn signal assembly is actuat­
ed.
o Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (M IL) is part
of the On-Boa rd D iagnostic (OBD II) system.
The symbol
¢111ij li gh ts up when the igni tion is
turned on and will turn off after the engine has started and has sett led at a constant idle
speed. This ind icates that the MIL is working
properly .
The warning light i lluminates when there is a
malfunction in the engine e lectronic system .
Contact your authorized Audi dealer and have
the malfunction corrected.
An imp roperly clo sed fuel filler cap m ay al so
c au se the MIL light to illuminate (onl y
v ehicles with ga soline eng ine)
c:> page 250.
F or more in format ion c:> page 2 7 .
Ci:> Adaptive Air Suspension
A ppl ies to vehicles: with Ada ptive Ai r Susp en sio n
This II warning/indicator light has the fol­
l owing f unctions:
- It illuminates for a few seco nds after the ig­
nition is t urned on as f unct ion check and
then goes out . -
If the warning/indicator light illuminates or
blinks contin uously, there is a system fault
in the Adaptive Air Suspension. A system
fau lt can result in lim ited ride comfort and
lo w ground clea rance . Drive safely to the
nearest authorized Audi dealer or qualified
wo rkshop, and have the fault corrected.
- If the warning/indicator light flashes, you
should not dr ive the veh icle . The flashing
warning/indicator light points to an extreme H igh level. A very
pronounced lifting of the
veh icle (ext reme H igh leve l) can result, for
examp le, when a heavy load is removed
from the vehicle. As soon as the level has re ­
t u rned to norma l, the wa rning/indicator
light stops flashing, and you can drive away.
- If the warning/indicator lig ht flashes in con ­
junction with the. warning/indicator
light, you should not dr ive off immediately
in order to prevent damage to the under­
body. The two warn ing/ indicator lights
flashing together points to an extreme Low level. A ve ry
pronounced lowering of the ve­
hicle (extreme Low leve l) can result, for ex­
ample, from a heavy load. As soon as the
level has retu rned to normal, the warn ing/
ind icator lights stop flashing, and you can
drive away.
(D Note
If the w arning/ indic ator l igh t flas hes in
conjunction with the. warning/ind icator
li ght, you shou ld not d rive the vehicle be ­
cause low-lying vehicle parts can bottom
out as you drive over uneven ground and be damaged as a result.
~ Adaptive Air Suspension
App lies to vehicles: wit h Adaptive A ir Suspensio n
This. warn ing/indicator light has the fo l­
low ing functions:
- It illuminates for a few seconds after the ig­ nition is turned on as function check and
then goes out .
- It comes on for approximately 15 seconds
as a warning of
reduced ground clearance , if .,,.

18 Instrum ent s and w arn ing /indic ato r light s
the dynamic mode is activated and if the ig­
nition is switched on
¢ page 157, Chassis
controls .
-If the warning/indicator light flashes in con­
junction with the
Ill warning/indicator
li ght, you shou ld not drive the vehicle imme­
diately in order to prevent damage to the
underbody . The two warning/indicator
lights flash ing together po ints to an ex­
treme Low level. A very
pronounced lower­
ing
of the veh icle (ext reme Low level) can re­
sult, fo r example, from a heavy load. As
soon as the leve l has ret urned to norma l
I
the warning/indicato r lights stop flashing,
and yo u can drive away.
{[) Note
If the warn ing/ indicator light flashes in
conjunction with the
Ill warning/indicator
light, you should not drive the veh icle be­
cause low- lying vehicle parts can bottom
out as you drive over uneven ground and
be damaged as a result.
~ Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The . warning/indicator lig ht ill uminates
when the ignition is sw itched on to remind
the driver and (on USA models only) any front passenger to put on the safety belt. Add ition­
ally, an acoustic warning (gong) w ill also
sound.
For more Information
c> page 173, Safety
belt warning light.
~D High beam
The II warning/indicator light illuminates
when the high beams are on or when you use
the head light flasher. For more informat ion
about us ing the h igh beams, see
c>page 63.
ill Tire pressure monitoring system -
telltale indicator lamp
The warning/indicator light appears in the
event of a significant loss of tire pressure or if there is a malfunction.
The ind icator light [IJ illuminates to check
the function w hen you switch on the ign ition.
If the
[IJ symbol remains on or blinks after
you sw itch on the ign it ion, there is a loss of
t ire p ressure or a system ma lfunction . If there
is a system ma lfunction, see your authorized
Audi dealer as soon as poss ible.
Deta iled informat io n on the tire pressure
monitoring system can be found in
c> page 301.
. CRUISE /''(") Cruise control
The IR;\l)~il (U SA mode ls) ,fl (Canada mod­
els) warning/indicator light i lluminates when
t h e cr uise control is activated .
ABS/(8) Anti-lock brake system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL) .
The ttl1 (USA models) /KO)l (Canada mode ls)
warning/indicator ligh t will come on for a few
seconds when the ignition is switched on. The
light will go out after an a utomatic check se ­
quence is comp leted .
There is a malfunct ion in the ABS when:
- The warning/indica tor l igh t does no t illum i­
nate when you switch on the ignition.
- The warning/indicator light does no t go o ut
after a few seconds.
- The warning/indicator light illum inates
while driving.
The brak e syst em will still respond e ven
withou t the ass istanc e of th e ABS sy stem .
S ee yo ur authorized Audi dealer as soon a s
p oss ible t o res tor e full braking p erf orm ance .
For more information regard ing the ABS
c>page 223 . II>-

M N
0 ...J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Instrument s and warnin g/indic ator ligh ts 19
The ABS war nin g lig ht a nd the bra ke w arn­
ing l ight come on t ogeth er. The ABS will not
work and you will notic e a c hange in brak ing
re spo nse and pe rformance.
Ma lfunction in th e brak e system
If the b rake warn ing light <=>page 19 and
the ABS warning i lluminate
together there
may be a ma lfunction in the ABS, and there
may a lso be a malfunct ion in the brake system
itself <=>,&. .
In the event of a
m alfun ct ion in the b rake
s ys tem
the warning/indicator light 1111
(USA models) . (Canada models) in the in ­
strument cluster flashes. By pressing the
ICHECKI button, you can bring up a driver
message which explains the malfunct ion in
more deta il. Please note
<=>page 32.
M alfunction in t he e lectronic diff erential
lock (EDL)
The EDL works together with the ABS. The
ABS warning light will come on if there is a
malfunct ion in the EDL system
<=> page 223.
See your autho rized Aud i dealer as soon as
possib le.
.&, WARNING
-
- If the ml (USA models) ;tlJ (Canada
models) warning light does not go out,
or if it comes on while driving, the ABS
system is not working properly. The vehi­
cle can then be stopped only with the
standard brakes (without ABS). You will
not have the protection ABS provides.
Contact your authorized Aud i dealer as
soon as poss ible.
- If the
1111 (USA models)/ . (Canada
models) brake system indicator light
tu rns on together with the ABS and ESC
indicator ligh ts, the ABS/ESC regu lating
f unction may have failed. F unctions that
stabilize the vehicle are no longer availa­
ble. This could cause the vehicle to
swerve and increase the risk of sliding.
Drive carefully to the nearest authorized
Audi dealer or other qualified workshop and have the malfunction corrected.
:l~ /(® ) Parking brake
The indicator light monitors the parking
brake.
When the parking brake is applied and the ig­
nition is switched on, the. (USA models) /
• (Canada models) indicator light comes on .
The ind icator light must go out when the
parking b rake is released.
BRAKE/CC Dl Brake system
The warning/indicator light flashes if brake
fluid level is low, if there is an
ABS system
ma/function or a parking brake ma/function.
The 1111 (USA models)/ . (Canada models)
light illum inates when the ignition is turned
on.
It goes out after the eng ine has been
started . This indicates that the bra ke warning
l ight is functioning properly.
If the brake w arning light d oes not light up
wh en th e eng ine i s cran king, th ere ma y be a
malfunction in the ele ct ric al sy ste m . In thi s
c ase , conta ct your Audi de aler .
If the brake system warning/indicator light
flashes, there is a b rake system ma lfunction .
By pressing the
I CH ECK i button, you can bring
up a driver message which expla ins the ma l­
function in more detai l
<=>page 32.
If the ABS fai ls, the ABS wa rn in g/ indicator
li ght
ml (USA mode ls)/ [§] (Canada models)
flashes together with the brake system warn­
ing/indicator light<=>,&. .
(USA mode ls): If the warn ing light
1111 and
the warn ing light
El il luminate togethe r, im­
med iate ly contact yo ur a utho rized Aud i dea ler
or qualified workshop to have all brake pads inspected ¢
page 36.
When the light comes on, an aud ible warn ing
s ignal is also g iven.
.&, WARNING ~ ~
- If the 1111 (USA models) . (Canada
models) brake system indicator light
turns on together with the ABS and ESC

20 Instrum ent s a nd w arn in g/i ndic ato r light s
indicator lights, the ABS/ESC regu lating
function may have failed. Functions that
stabilize the vehicle are no longer availa­ ble . This could cause the vehicle to
swerve and increase the risk of sliding.
Drive carefu lly to the nearest authorized
Audi dealer or other qualified workshop and have the malfunction corrected.
- If the brake warning/indicator light does
not go out afte r a few seconds and the
par king brake is released, or ligh ts up
wh ile you are driving, the fluid level in
the brake fluid reservoir is too low. If you believe that it is safe to do so, proceed
immediately at low speed to the nearest
authorized Audi dealer or qualified repair
facility and have the brake system in­
spected.
- Always keep in m ind that after several
brake applicat ions, you will need greater
pressure on the b rake pedal to stop your
vehicle . Do not re ly on stra ined brakes to
respond w ith maximum stopp ing power
in cri tic al situations. You must a llow for
increased bra king distances. The extra
distance used up by fad ing brakes could
lead to an accident.

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
Driver information
display
Introduction
General notes
The driver information display inside the in­
strument cluster provides you, the driver ,
with much useful information .
Fig. 9 In st ru men t cl uster: ce nte r dis p lay
Info rmation from the Drive r Information Sys ­
tem is shown in the display in the center of
t he instrument cl uster .
When you turn on the ignition and while you
are driving, some functions and vehicle com­ ponents are scanned fo r their operating sta­
t us. Malfunc tions or required service proce­
dures are signal led aud ibly and shown by red
and yellow lighted symbols and rem inders to
the dr iver in the display.
T he driver i s also shown information abou t ra­
d io and CD operation and directions for the
nav igation system . You can f ind additional in­
formation on these subjects in the MMI man­
ua l.
The Driver Information System prov ides the
following functions:
Sound system disp lay ¢
page 21
Outside air temperature ¢page 22
Digital speedometer ¢
page 22
Door open indicator ¢page 22
D efective light b ulb ¢
poge23
Serv ice i nte rval display ¢page 23
Auto Check system ¢
page 30
Driver information ¢
page 30
Driver inform ation di spl ay 21
Speed warning system ¢page28
T rip computer ¢
page24
Cruise con trol ¢page 113
Adapt ive cruise control* ¢
page 115
Selector lever pos ition ¢page 139
Adapt ive Air Suspension * ¢
page 160
Tire pressure monitoring ¢page301
(D Tips
In the event of a malfunction either a red
or ye llow icon appears in the display . Red
symbols indicate
Dang er ¢ page 31 . Yel­
l ow symbo ls indicate a
Warning
¢ page 34.
Sound system display
Fig. 10 D isp lay: so un d syste m
If priority 1 or pr iority 2 faults are not shown
by the Auto Check Control, the name of the ra­
dio station you are tuned to or t he frequency
and the recept ion range are shown in the up­
per area of the d isplay.
When the CD is in use, the tit le of the track
being played is shown . T he number of the CD
(CDI to CD6) cur rently be ing played is also
shown.

22 Driver in formation d ispl ay
Outside temperature display
Fig. 11 Display : outside temperature
At temperatures below 41 °F (+S °C) a snow­
flake symbol appears ahead of the tempera­
ture display . It is intended to remind the driv­
er to pay spec ial attent ion to
ic e on the roa d.
If the vehicle is stationary, or if you are driving
at a very low speed, the temperature shown in
the display might be slightly higher than the
actual outside temperature . Th is is caused by
the heat being rad iated from the engine .
If you have selected the °C (degrees Celsius)
unit for temperature in the MMI, the outside
temperature display also appears automat i­
cally in
°C.
A WARNING
- Never rely excl usively on the outside
temperatu re d isplay to determine if a
road surface is icy or not . Keep in mind
that road surfaces, especially bridges
and overpasses, could be ice covered and
s li ppery even at an outs ide temperature
above 41 °F (+ S °C).
- Always remember, even if the "snow­
flake" symbol (ice warn ing) does not ap­
pear in the display, black ice could be on
the road.
- Always reduce your speed and dr ive with
special care in cold weather conditions
when the chance of encountering icy road s urfaces increases .
Digital speedometer
Fig. 12 Display: Digi tal speedometer
Current speed appears in the disp lay. Speed is
shown in 1 mph measures (USA models) or 1
km/h measures (Canada models) .
You can switch the disp lay from m iles to kilo­
meters and vice versa via the MMI.
Open door or trunk lid warning
The pictogram alerts you when doors or the
rear lid have been left open .
Fig. 13 Display: open doo r or rea r lid wa rning
With the ign it ion sw itched on, the ope n door
or rear lid warning illuminates when at least
one door or the hood or the trunk lid is not
cl osed . The symbol a lso shows you
which
doo r(s) o r lid is not closed.
In the illustration
~ fig . 13 it is the dr iver's
doo r, the left rear door and the rear lid. As
soon as all the doors, the hood, the rear lid
and the f uel filler cap are prope rly closed, the
door and rear lid warning turns off and the
Driver Information System functions selected
are displayed again.

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
Defective light bulb warning
The defective light bulb warning tells you
when a vehicle light bulb has become defec­
tive.
Fig . 14 D isplay : defective lig ht bu lb warn ing
The defective light bu lb warning monitors the
function of the light bulbs . If th is symbol
S:!I
illuminates, a brake light, a turn signal (front
or rear), a headlight, the backup light, a fog
light or a rear fog light has failed.
A WARNING
- light bu lbs are pressurized and could ex­
plode while they are being changed caus­
ing serious personal injury.
- Work w ith due care when handling the
high-voltage section of gas discharge
(xenon) lights. Fa ilure to do so could re­
sult in dea th o r se rious injury.
(D Tips
Have the bulb replaced or the connection
repa ired by you r autho rized Aud i Service
department.
Dri ver inform ation di spl ay 23
Service interval display
The service interval display reminds you when
your next service is due .
Fig . 1 5 Display: Serv ice interva l d isplay
T he schedule for the nex t oi l change or inspec­
tion is ca lculated automatica lly and disp layed
accordingly. The disp lay works in two stages:
Service reminder
30 days before t he nex t se rvice is due, a serv­
i ce reminde r appea rs in the display whe n you
turn on the ignition
~fig. 15.
After about 5 seconds the display switches
back to norma l. The distance and time re­
mai ning are updated each time the ignit ion is
turned on unt il t he da te d ue for se rv ice is
reached.
Service due
When the due date fo r se rvice is reached, the
mes sage
Se rv ice due! appears in the instr u­
ment cluster immed iate ly after yo u tur n on
the ignit ion. Addit iona lly, a warning tone
sounds. After about 5 seconds the disp lay
switches back to normal.
Calling up the service schedules
If or when an oil change o r inspection is due,
can be shown in the MMI display by selecting
the service in terval d isplay in the car menu .
Se lect
I CAR I funct io n button > Sy stem s* con­
trol button
> S ervice inte rval display or I CAR !
function button > Car sy stem s* contro l but -
ton
> Servicing & chec ks > Service in te rv als . ..,_