2015 AUDI Q7 instrument cluster

26 Driver in formation d isplay
• To d is p lay tri p information within a memory
l evel, press the top or bottom part of the
function selection switch
@ .
The t rip computer w ill not operate unless the
ignition is on. When you turn on the ignition,
the function that was in use when you last
turned the ignit ion off will be d isp layed .
I n addi tion to informa tion abo ut the trip com­
puter (trip computer 1, 2 and the efficiency
prog ram*), information about other systems
can also be shown in the display. To switch the
d isp lay between the d ifferent information,
tap the I RESET! button @ briefly.
Resetting values to z ero
• Se lect a va lue in the desired trip computer
or in the efficiency program* .
• Press and ho ld the I RESE T
I button @for at
least one second. All va lues in the selected
trip computer or in the eff iciency program*
are reset to zero .
If the data in trip compute r 1 are deleted,
then the values in the efficiency program* will
a lso be reset.
W ith some vehicle equipment leve ls, the va l­
ues for the s ingle trip or total tr ip memory
can also be reset in the MMI
c::;, page 26.
@ Tips
All stored values will be lost if the vehicle
battery is disconnected.
MMI settings
Basic settings for the trip computer con be
mode in the MM I.
• Se lect : ICAR !funct io n but ton> Systems *
control button > Instrument cluster > On­
board computer 1 or On -boa rd computer 2.
The val ues in the single -trip or the to tal-tr ip
memory can a ll be reset to zero at t he same
time under
Reset in the menu.
I n addi tion, you can de termine w hat inform a­
tion from the trip computer shou ld be shown
in the instrument cluster display. If one of the pieces of driver info
rmation is turned
Off , that
drive r information will not be shown in the
display. The info rmation w ill cont in ue to be
ca lculated by the tr ip comp uter and can be
turned back
On at any time.
(j) Tips
- Th is function is not available on all
vehicles.
- The d riving info rmation in the eff iciency
program * is also reset to zero with the
single-trip memory.
Efficiency program
Description
Applies to vehicles: with efficiency program
Fi g. 19 Displ ay: eff icie ncy prog ra m
• Press the I RESE T! button @ c::;, page 25,
fig . 18
repeatedly unt il the eff ic iency pro­
gram appears in the display .
The efficiency program can he lp you to use
less fuel. It evaluates driving information in
r eference to f uel consumption and shows oth­
er equipm ent influ encing consumption . Fu el
e co nomy messages
c::;, page 27 provide t ips
f o r eff ici en t driving.
The efficiency program uses distance and co n­
sumption data from trip computer
1. I f t he
da ta ar e deleted in the effi ciency p rogram,
t h ose v alues are a lso rese t in tr ip co mpu ter
1.

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
Other equipment
Applies to vehicles: with efficiency program
Fig. 20 D isplay : ot her equipment
• In the efficiency program, press the function
s elec tion switch
q page 25 , fig. 18@ re­
peatedly until the other equipment appears
in the d isplay .
Other equipment that i s cu rrently affecting
f uel consumption is lis ted in the eff iciency
program . The display shows up to three other
items of equipment @. The equipment using
the most fuel is l isted first. If more than three
items using fue l are switched on, the equ ip­
ment that is currently using the mos t fu el is
d isp layed .
A scale @also shows the current total con­
sumpt io n of all other equ ipment .
Fuel economy messages
Applies to vehicles: with efficiency program
Fig. 2 1 Dis pl ay: fuel e co n omy messa ge
-.:,
~
Fuel economy messages are displayed when
fuel consumption is inc reased by certain con­
d itions . If you follow these fuel economy mes­
sages, you can reduce your vehicle's consump­
tion of fuel. The messages appear automati ­
cally and are o nly displayed in the eff ic iency
Dri ver inform ation di spl ay 2 7
program . The fue l economy messages t urn off
automatica lly after a certain period of time .
• To tu rn a f uel economy message off immedi­
ately after it appears, press the
I RESE TI but­
ton ¢
page 25 , fig. 18 @, or
• Press the function selection switch
r::!) page 2 5, fig . 18 @ .
{I) Tips
-Once you have turned a fuel economy
message off, it will o nly appear again af­
ter yo u turn the ign ition on again.
- Th e fuel economy messages are not dis­
played in
every i nstance, but rather in in ­
tervals
over a period of time.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (M IL) ¢..ij in
the instrument cluster¢
page 14, fig. 8 is
part of the On-Board Diagnos tic (OBD
II) sys­
tem .
The warning/ind icator light ill um inates when
the ignition is switched on and goes out after
the engine star ts and the id le has stabilized.
This indicates that the M IL is working prope r­
ly .
If the light does not go out after the engine
is started , or illuminates while you are dr iv­
ing, a malfunction may exist in the engine sys ­
tem . If the light illuminates, the catalytic con­
verter could be damaged .
Con tinue driving
with reduced powe r (avoid­
ing sustained high speeds and/or rapid accel ­
erations) and have the cond ition co rrected .
Contact your a uthorized Aud i dea ler.
If the light illum inates, the elec tronic speed
limiter may also be malfunctioning . For more
information ¢
page 28, Electronic speed
limiter.
An improperl y closed fuel filler cap may also
cau se th e MIL light to illum inat e (onl y
ve hicl es with gas oline engi ne) ¢
page 250 .

30 Driver in formation d ispl ay
(30 km/h to 240 km/h) . Settings can each be
adj usted in intervals of S mph (10 km/h) .
Auto Check Control
Introduction
The Auto-Check control monitors the function
of certain veh icle featu res and components . It
simply makes sure these features and compo­ nents are work ing proper ly . The Auto -Check
contro l wo rks as long as the ignition is on, as
well as whenever the vehicle is driven.
If a componen t is ma lf u nctioning or if the
n eed for an urgent repair has been detected,
this will appear in the instrument cluster dis­
p lay . You w ill a lso hear an audible warn ing
tone . The displays are co lor coded in e ither
red or yellow depending on their level of prior­
ity .
A red symbo l means
Dange r, a yellow symbo l
indic ates
Warning . In certain s ituations, in­
formation message for the dr iver appear in
addit ion to the red and yellow symbols.
Function te st : automat ic transmi ssion
The Auto -Check Control will automat ica lly
perform a test each time you switch on the ig­
n ition. With the selector lever in P or N, the
following message appears in the display :
When station ary apply brake pedal while se­
lecting gear
When you select a different gear (for exam ­
p le : R, D, etc.), the message will d isappear
and the Auto-Check function is d isplayed .
I f the re is a m alfu nction, then the malfunc­
tion message w ill appear about 15 seconds af ­
ter the yo u start the vehicle. At t he same time
you will hear a warning tone .
Driver information messages
Driver information messages are shown in the
instrument cluster display in addition to the
red and yellow symbols .
Fig. 24 Ins trume nt cl ust er: CHECK b utto n
For example, if the transmiss ion selec to r l ever
is not in the P position when the engine is
turned off, the following message appears :
Shift to P otherwise vehicle can roll away.
Door s do not l ock if you are not in P .
The ig nition key can only be removed with the
selector in this position . Th is and other mes­
sages are bro ugh t up if a func tion cannot be
carr ied out.
Driver messages and red symbols
If a red symbol appea rs in the display, a d river
message can be shown by pressing the
I CH ECK I button.
For example, the symbo l for a problem w ith
engine oil p ressure . appears in the d isp lay .
If you then p ress the
I CHECK I button , the fol­
lowing dr iver mess age appears in the display:
Switch off engine ! Oil pr essure too low
The driver message in the display goes out af­
ter about 5 seconds . The driver message can
be displayed again by briefly press ing the
I CH ECKi button.
Driver messages and yellow symbol s
If a yellow symbol appears in the display, a
driver message is also displayed automatical-
~ ~

M N
0 ...J
'SI: ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
For example, the symbol II appears in the
display, indicating low windshield washer flu­
id level. The follow ing message also appears:
Please refill washer fluid
The driver message disappears after a few
seconds. The driver message can be d isp layed
again by briefly pressing the
!CHECK I button.
Red symbols
Fig. 25 Display: engine coolant level warning (prio rity
1)
With a priority 1 malfunction, a large symbol
appears in the center area of the display
¢ fig . 25 . Wh en the symbo l appears, three
warning tones sound in succession. The sym­
bol continues to blink until the malfunct ion
has been repaired.
If there are
more than one priority 1 ma lfunc­
tions, the symbols appear one after the other for about 2 seconds.
An additional driver message can also be dis­
played by briefly pressing the
I CHECK ! button.
The red symbols mean:
Alternator malfunct ion
¢page31
USA models: Brake system
malfunction
¢page32
Canada models: Brake sys­
tem malfunction
¢pa ge32
Engine coolant level too
low/engine coolant temper­
ature too high
¢page32
Driver information display 31
@ Tips
Engine oil pressure too low
¢page 33
Refill Ad Blue*
¢page 252
AdBlue malfunct ion*
c!>page252
Faulty steering
c!>page 33
Faulty ignition switch
¢page 33
-If the warning/indicator light 11111 (USA
models)/ . (Canada models) in the in­
strument cluster flashes, there is a brake
system malfunction. By pressing the
!CHECK I button, you can bring up a driver
message which exp lains the malfunction
in more detail. Please note ¢
page 32.
-Speed warnings threshold 1. (USA
mode ls)/ . (Canada models) and
threshold 2. (USA models) . (Cana­
da models) are a lso shown as red sym ­
bols. The warning is always shown as a
small symbol in the uppe r area of the
display
c!> page 28.
0 Alternator malfunction
If the . symbol in the instrument panel dis­
play flashes, then there is a malfunction in the
alternator o r the vehicle elect ronics. A warn­
ing to the driver will appear, too . The driver
warning goes out after about 5 seconds, but it
can be brought up at any time by pressing the
ICHECK I button aga in.
Usually, you can still drive to the next deale r­
ship . Turn off all but the most necessary elec­
trical consumers, since these drain the vehi­
cle's battery.
([) Note
If the . warning symbo l (coo lant system
malfunction) also lights up on the instru­
ment panel during the trip¢
page 32,
then you have to stop immediately and ..,_

36 Driver in formation d isplay
(0 ) Worn brake pads
rlJ Br ake pa ds !
If the warn ing light illum inates, immediately
contact your authorized Audi dealer or quali­
fied workshop to have all brake pads inspect­
ed. On USA models the wa rning light
rlJ
comes on together wi th the warn ing ligh t
1111 -Both sets of b rake pads on an axle
must always be replaced at the same time .
A WARNING
Driving with bad brakes can cause a colli­
sion and serious personal injury .
- If the warning light
rlJ and the warning
light
11111 ) with the message B rake
pads !
comes on in the instr ument cluster
display, immediately contact your au­
thorized Aud i dealer or qualified work­
shop to have all brake pads checked or
replaced if necessary .
~(]) Headlight range control
El Head light rang e control d efe ctiv e !
-
If the symbol illuminates, the dynamic head­
light range control is no longer working prop ­
erly . Have the system checked and repaired at
your author ized Audi dealer.
'I=?; , Engine oil level
Ill Pleas e che ck oil l evel
When the symbol illuminates, check the en­
gine o il level as soon as poss ible
¢ page 260 .
Top off the oil at you r earliest oppo rtunity
~ page 261.
't'.:r .., Engine oil sensor defective
• Oil l evel ! Sensor d efe ctive
If the symbol illuminates, contact your au­
thor ized A udi dealer and have the o il sensor
i nspected. Un til you have th is done, check the
l ) - : USA mod els onl y
oil level each time you refue l just to be on the
safe side ¢
page 260.
!?' Engine speed limitation
Applies to vehicles: wit h engine speed li mitatio n
(Pl Do not e xceed ma x. engine speed of
XXXX rpm
The (Pl symbol illuminates when there is an
engine contro l malfunction. The indicator
li ght
GB in the instrument cluster also illumi­
nates. The engine speed is limited to the
speed displayed in the driver informa tion sys­
tem . Keep in mind that the engine speed w ill
not exceed the value d isplayed in the dr iver in­
format ion system, for example when down­
shifting.
Please go to an author ized Audi dealer or oth ­
er qualified workshop to have the malfunct ion
repaired.
~ Diesel particulate filter clogged
Applies to vehicles: wi th diese l eng ine a nd diese l par ticu ­
late filter
II Particulate filt er See o wner' s manua l
When the II symbol illuminates, you can a l­
ter your driving style to ass ist the filter sel f­
cleaning process . Drive for approximately 15
minutes with the selector lever in the S posi ­
t ion at a m inimum speed of 37 mph (60 km/
h) and an eng ine speed of approximately
2,000 RP M. T he temperat ure increase that
will res ult from this can burn off the soo t in
the fi lter . The symbol will switch off when the
cleaning is successful. After a successful
cleaning, there is no need to bring the car to
an authori zed dea ler or qualified workshop
because th is is part of normal vehicle opera­
t ion .
If the symbol
II does not switch off, see your
authori zed dea ler or other qualified workshop
to have the problem corrected.
For more information on the diesel particu­
l ate fi lter, refer to ¢
page 231.

M N
0 ...J
'SI: ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
Clos ing re ar lid /trunk lid
"' Press the close button in the open rear lid
~ fig. 40. The trun k lid moves to the closed
posit ion by itself and soft close locks it auto­
matically ~&_ .
"' The closing process
is stopp ed immediately
if the close button in the rear lid is pressed
again.
"' By push ing the button again, the rear lid is
opened again .
Setting the rear lid o pen po sition
"' Bring the rear lid into the desired open posi­
t ion. The posit ion can only be stored when
the lid is above a certain height .
"' Press and hold the
~fig . 40 button for at
least four seconds to store the desired open
pos ition.
"'T o set a h igher open position , wait at lea st
five seconds and then carefu lly press the
rear lid upward.
"' Press and ho ld the ~
fig. 40 button again for
at least four seconds and this will store the
new open position.
A WARNING
- Never close the rear lid inattentively or
without checking fi rst . Although the
closing force of the rear lid is lim ited,
yo u can st ill ser iously injure yourself or
others.
- Always ensure that no one is w ith in
range of the rear lid when it is mov ing, in
part icu lar close to the h inges and the up­
per and lowe r edges -fingers or hands
can be p inched.
- T o help p reven t po isonous exha ust gas
from being d rawn into the vehicle, al ­
ways keep the rear lid closed while driv­ ing. Never transport objects larger than
those which fit completely into the lug­
gage area, because then the rear lid can­
not be fully closed .
- Never leave your vehicle unattended es­
pecially with the rear lid left open. A
child could crawl into the car through the
luggage compartment and pull the lid
-
Opening and clo sin g 47
shut, becoming trapped and unable to
get out. To reduce the risk of personal in­
jury, never let ch ildren play in or around
your veh icle . Always keep the rear lid as
well as the vehicle doors closed when not in use .
- If there is a l uggage rack or b icycle rack
mounted on the rear lid, it may not be
ab le to open completely o r an opened
rea r lid may close by itself because of the
ad ded weight. So the open rear lid mus t
be supported or the weigh t must be re ­
moved from the luggage rac k first .
(D Tips
- If the rear lid is open o r not properly
locked when the ign ition is turned on ,
t he door and rear lid warning ~
page 22
appears in the instrument cluster dis­
play.
- The automatic rear lid opening/clos ing
process can be stopped by ho ld ing the
rear lid w ith your hand. The lid can then
be further opened/closed by hand.
- If there is a mechan ica l problem wit h the
automatic rear lid
opening process or
there is an obstruction, the process is
stopped immediately .
- If there is a mechan ica l problem with
au ­
tomatic closing for the rear lid or there
is an obstruction, it ope ns again slightly
r ight away. Check to see why the rear lid
cou ld not be closed before attempting to
close it again .
- If the rear lid on a locked vehicle is un­
locked with the midd le button
c:5 on the
remote key, the rear lid i s automat ically
locked agai n immed iate ly afte r closing.
T his is indicated by the turn signals
blinking .
- T he followin g applies to vehicles equ ip­
ped with the Convenience key* feature: i f
the remote control key is left in the lug­
gage compartment, luggage compart­
ment w ill automatically unlock itself a f­
ter you lock the vehicle. Th is prevents
you from unintentionally lock ing you r
key in the luggage compartment. ...,

60 Clear vision
Clear vision
Lights
Switching the headlights on and off
In the "AUTO" position, a light sensor auto­
matically switches the head -and taillights on
and off in response to light conditions .
Fig. 56 Instrument pane l: lig ht sw it ch
The light switch must not be overturned past
the stops in
either direction.
Switching on automatic headlight control
.,. Turn the light switch to AUTO ¢ fig. 56.
Switching on the side marker lights
... Turn the light switch to :o o:.
Switching on the headlights and high
beam
... Turn the light switch to tD .
... Push the high beam lever forward towards
the instrument panel¢
page 63 .
Switching off the lights
... Turn the light switch to 0.
The headlights only work when the ignition is
switched on. While starting the engine or
when switching off the ignition, the head­
lights will go off and on ly the side marker
lights will be on.
After starting the engine, the headlights are
automatically adjusted* to the load and angle
of the vehicle (for example, during accelera­
tion, braking). This prevents oncoming traff ic
from experiencing unnecessary headlight
glare from your headlights. If the
system is not ope rating properly, a
warn ing symbol in the Auto-Check Control is
displayed
¢ page 36.
With the side marker lights or headlights
switched on, the symbol next to the light
switch i lluminates
:oo :.
Daytime running lights
- USA models :
The daytime running lights
w ill come on automatically when the igni­
tion is turned on and the light switch
¢ fig. 56 is in the O position or the AUTO po­
sition (only in daylight conditions). The
Day­
time running lights
function can be turned
on and off in the MMI menu
Exterior light­
ing
c> page 61.
- Canada models: The daytime running lights
w ill come on automatically when the igni­
tion is turned on and the light switch
¢ fig. 56 is in the O position or the AUTO po ­
sition (only in daylight condit ions) ¢
.&..
Automatic headlight control
In the switch position AUTO the automatic
headlight control
is turned on. The low
beams and tail lights are turned on automati­
cally through
a light sensor as soon as ambi­
ent brightness (e .g . when driving into
a tun­
nel) falls below
a value preset at the factory .
When ambient brightness increases again,
the low beams are turned off again automati­
cally ¢
A.
In the AUTO position the low beams are
switched off automatically when the ignition
is turned off.
Light Sensor Malfunction
In the event of a light sensor malfunction , the
driver is notified in the instrument cluster dis­
play:
£I Automatic headlights / automatic wipers
defective
For safety reasons the low beams are turned
on permanently with the sw itch in
AUTO.
However, you can conti nue to turn the lights
on and off using the light switch . Have the ..,.

light sensor checked as soon as possible at an
authorized Audi dealer or qualified workshop.
A WARNING
- Daytime running lights and automatic
headlights are only intended to assist
the driver. They do not relieve the driver
of his responsibility to check the head­
lights and to turn them on manually ac­
cording to the current light and visibility
conditions. For example, fog cannot be
detected by the light sensors*. So always
switch on the headlights
~D under these
weather conditions and when driving in
the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists. Always turn on
the headlights so that you can see ahead
and so that others can see your car from
the back.
- Please obey all laws when using the
lighting systems described here.
@ Tips
-With the switch in AUTO front fog lights
and rear fog lights cannot be turned on in addition.
- The light sensor for headlight control is
located in the rear view mirror mount.
You should therefore not apply any stick­
ers to the windshield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted ¢
page 61.
-When you remove your key from the igni­
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv­
er's door is open.
- In cool or damp weather, the inside of
the headlights, turn signals and tail
lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clear shortly after
M "' switching them on. This does not affect 0
~ the service life of the lighting.
rl I.O
"' rl
"' rl
Clear vision 61
-In the event of a light sensor malfunc­
tion, the driver is notified in the instru­
ment cluster display¢
page 35.
Adjusting exterior lighting
The functions are set in the MMI.
.,. Select: !CAR ! function button > Systems*
control button > Exterior lighting. Or
.,. Select:
I CAR I function button > Car systems*
control button > Vehicle settings > Exterior
light ing.
Coming home (Lights when leaving car),
Leaving home (Lights when unlocking car)
The coming home function illuminates the
area outside the vehicle when you turn the ig­
nition off and open the driver's door. Depend­
ing on vehicle equipment, the function can be
switched on and off or the length of ti me the lights remain on* can be adjusted .
The leaving home illuminates the area outside
the vehicle when you unlock the vehicle . This
function can be switched on and off .
The Coming home and Leaving home func­
tions only operate when it is dark and the light switch is in the
AUTO position.
Daytime running lights
USA models: The daytime running lights can
be turned on or off using this function.
Canada models: The function cannot be
turned
off. It is activated automatically each
time the ignition is turned on. This menu item is shown "greyed out" .
Front fog lights
Fig. 57 Instrument panel: light switch