2015 AUDI Q5 rims

M N
co
a:
co
,...., \!) ..,.,
N ..,., ,....,
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
- After washing the vehicle, the braking effect
may be delayed due to moisture on the
brake rotors or ice in the w inter. The brakes
must be dried first w ith a few careful brake
applications.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior m irrors in
to reduce the risk of damage to the mirrors.
Power folding exterior mirrors* must only
be fo lded in and out us ing the power folding
funct ion.
- To reduce the risk of damage to the rims
and tires, compare the width between the
whee ls on your vehicle w ith the distance be­
tween the g uide rails in the car wash .
- To red uce the risk of damage, compare the
height and width of yo ur vehicle with the
Care and cleaning
height and w idth of the inside of the car
was h.
- T o prevent paint damage, do not wash the
vehicle in direct sunlight.
- To reduce the ris k of damage to the sur face,
do not use insect remov ing sponges, kitchen
sponges o r similar items.
- Matte finish painted veh icle components:
- To reduce the risk of damage to the sur-
face, do not use polishing agents or hard
wax.
- Never use protective wax. It can destroy
the matte finish effect.
- Do not place any stickers or magnetic
signs on vehicle parts painted w ith matte
finish paint. The paint could be damaged
when the stickers or magnets are re­ moved.
@ For the sake of the environment
Only wash the vehicle in facilities spec ially de­
s igned for that purpose. Th is w ill reduce the
r isk of dirty water contaminated w ith oil from
entering the sewe r system.
Cleaning and care information
When clea ning and caring for individual vehicle
components, refer to the following tables. The
information conta ined there is simply recommen -dations. For questions or for components that
are not listed, refer to an authorized A
udi dealer.
Also follow the information found in
¢ A.
Ext erior cl eaning
Component Situation Solution
Wind shi eld wiper
Deposits ¢ page 58, Cleaning windshield wiper blades
blades
H eadlight s/
Deposits Soft sponge with a mild soap solutional
tail light s
S ensors /
Deposits Sensors: soft cloth with solvent-free cleaning solution
camera le nses Camera lenses: soft cloth with alcohol-free clean ing solu-
tion
Snow/ice Hand brush/solvent-free de -ic ing spray
Whe els Road salt Water
Brake dust Acid-free special cleaning
solution
Exhau st tail p ipe s Road salt Water, cleaning solution suitable for stainless steel, if nee-
essary
209

M N
co
a:
co
,...., \!) 1.1"1
N 1.1"1 ,....,
Care and cleaning
Component Situation Solution
Te xtile s
Deposits adhering to Vacuum cleaner
artificial leather, the surface
Alcantara Water-based depos its Absorbent
cloth and mild soap solutiona)
such as coffee, tea,
b lood, etc.
Oil-based deposits Apply a m ild soap solutiona>, blot away the dissolved oil or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Specia l sta in remover, blot with absorbent material, treat
as ink, na il polish, la- afterward with mild soap solution, if necessarya>
tex paint, shoe pol-
ish, etc.
Natural leather Fresh stains Woo
l cloth with a mild soap solutiona>
Water-based deposits fresh stains : absorbent cloth
such as coffee, tea, dried stains: stain remover suitable for leather
blood, etc.
Oil-based deposits Fresh stains: absorbent cloth and stain remover sui tab le
such as oil, make-up, for leathe r
etc. dried stains: Oil cleaning spray
Special deposits such Spot remover suitable for leather
as ink, nai l polish, la-
t ex paint, shoe po l-
ish, etc.
Ca re Regularly apply conditioning cream that protects from
light and penetrates into the mate rial. Use specially-col-
ored conditioning cream, if necessary.
Carbon parts Deposits clean the same way as plastic parts
a) Mild soap sol ution : maximum two tablespoons of neutral soap in 1 quart (1 liter) of water
.8, WARNING
The windshield may not be treated with wa­
ter-repelling windshield coating agents . Un­
favorab le conditions such as wetness, dark­
ness, or low sun can resu lt in increased glare.
Wiper blade chatter is also possible.
@ Note
- Headlights/tail lights
- Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form.
- Wheels
-
- Never use any paint polish or other abra­
sive materials.
- Damage to the protective layer on the
rims such as stone chips or scratches must
be repaired immediately.
- Sensors/camera lenses
-Never use warm or hot water to remove
snow or ice from the camera lens. This
could ca use the lens to crack.
- Never use abrasive cleaning materials or
alcohol to clean the camera lens. This
could cause scratches and cracks.
- Door windows
-Remove snow and ice on windows and ex-
terior mirrors with a plastic scraper. To
211

M N ai
"' ~
-"' "' N
"' ...,
Wheels
Wheels and Tires
General information
.,.Che ck your tires regularly for
damage (punctures, cuts, cracks
and bulges). Remove foreign ob­
jects from the tire tread.
.,. If driving over curbs or similar
obstacles, drive slowly and ap­
proach the curb at an angle.
.,.Have faulty tires or rims re­
placed immediately.
"'Protec t your tires from oil,
grease and fuel.
.,.Ma rk tires before removing
them so that the same running direction can be maintained if
they are reinstalled .
.,.Lay tires flat when storing and
store them in a cool, dry location
with as little exposure to light as
possible.
(D Note
-Please note that summer and
winter tires are designed for
the conditions that are typical
in those seasons. Audi recom­
mends using winter tires dur­
ing the winter months . Low
temperatures significantly de­ crease the elasticity of summ­
er tires, which affects traction
Wheels
and braking ability. If summer
tires are used in very cold tem­
peratures, cracks can form on
the tread bars, resulting in
permanent tire damage that
can cause loud driving noise
and unbalanced tires.
-Burnished, polished or
chromed rims must not be
used in winter driving condi­
tions. The surface of the rims
does not have sufficient corro­
sion protection for this and
could be permanently dam­
aged by road salt or similar
substances.
Tire designations
Fig. 204 T ir e designations on the sid e-
wall ,..
235

Wheels
check the wheel alignment if
there is unusual wear.
- Have the wheels rebalanced if an
imbalance is causing noticeable
vibration in the steering wheel. If you do not, the tires and other
vehicle components could wear more quickly.
Treadwear indicator
Original equipment tires contain
treadwear indicators in the tread pattern, which are bars that are 1/16 inch (1.6 mm) high and are
spaced evenly around the tire per­
pendicular to the running direc­
tion ¢
fig. 205. The letters "TWI"
or triangles on the tire sidewall indicate the location of the tread­
wear indicators.
The t ires have reached the mini­
mum tread depth
l) when they
have worn down to the treadwear
indicators. Replace the tires with
new ones ¢Ai..
Wheel rotation
Rotating the wheels regularly is
recommended to ensure the tires
wear evenly . To rotate wheels, in­
stall the wheels from the rear
1> Obey any applicable regulatio ns in you r
country .
244
axle on the front axle and vice ver­
sa. This will allow the tires to
have approximately the same
length of service life .
For unidirectional tires, make sure
the tires are installed according to
the running direction indicated on
the tire sidewall ¢
page 264.
Hidden damage
Damage to tires and rims can of­
ten occur in locations that are hid­
den. Unusual vibrations in the ve­
hicle or pulling to one side may
indicate that there is tire damage.
Reduce your speed immediately .
Check the tires for damage. If no
damage is visible from the out­
side, drive slowly and carefully to
the nearest authorized Audi deal­
er or authorized repair facility to
have the vehicle inspected.
8_ WARNING
Tread that has worn too low or
different tread depths on the
tires can reduce driving safety.
This can especially have a nega­
tive effect on handling, on the
risk aquaplaning when driving
through water, when driving

M N
co
a:
co
,...., \!) 1.1'1
N 1.1'1 ,....,
Determining correct load
limit
Use the example below to calcu­
late the total weight of the pas­
sengers and luggage or other
things that you plan to transport
so that you can ma ke sure that
your vehicle will not be overload­ ed .
Steps for Determining Correct
Load Limit
1 . Locate the statement "THE
COMBINED WEIGHT OF OCCU­ PANTS AND CARGO SHOULD
NEVER EXCEED XXX KG OR XXX
LBS"on your vehi cle's pla card
(tire inflation pressure label)
¢ page 245 , fig. 206.
2 . Determine the combined
weight of the driver and pas­
sengers that will be riding in
your vehicle.
3 . Subtract the combined weight
of the driver and passengers
from
"XXX " kilograms or "XXX"
pound s shown on the sticker
¢ page 245 , fig. 206 .
4. The resulting figure equals the
available amount of cargo and luggage load capacity. For ex­
ample, if the
" XXX" amount
equals 1400 lbs. and there will
Wheels
be five 1 SO lb s. passenger s in
your vehicle, the amount of available cargo and luggage load capa city is 650 lb s.
(1400-750 (5 X 150) = 650
lb s.)
5. Determine the combined
weight of luggage and cargo
being loaded on the vehicle .
That weight may not safely e x­
c eed the available cargo and
luggage load capa city cal culat­
ed in Step 4 .
6. If your vehicle will be towing a trailer, load from your trailer
will be transferred to your vehi­
cle. Con sult thi s manual to d e­
termine how this redu ce s the
available cargo and luggage load capacity of your vehicle .
.,.Check the tire sidewall
(¢ page 235 , fig. 204) to deter­
mine the designated load rating
for a specific tire.
Wheel bolts and rims
Wheel bolts
W heel bolts mus t be clean and loose n/tighten
easily .
Rims
Rims with a bo lted r im ring* or with bo lt ed wheel
cove rs* cons ist of multi ple p ieces . These compo­
nents were bolted together using specia l bolts
and a spec ia l procedu re . You must not repa ir or
disassemb le th em
i::> Li::,. . ..,.
249

Wheels
A WARNING
Wheel bolts that are tightened or repaired in­
correctly can become loose and resu lt in loss
of vehicle control , which increases the risk of
an acc ident. For the correct tightening specifi­
cat ion, refer to
c:> page 261, After changing a
wheel.
- Always keep the wheel bolts and the threads
in the wheel hub clean and free of grease.
- Only use wheel bo lts that fit the r im .
- Always have damaged rims repaired by an
authorized Aud i dealer or authorized repair
facility. Never repair or disassemble rims
you rself, because this increases the risk of
an accident.
Winter tires
W inter tires sign ificantly improve the vehicle's
handling when driving in w inter condit ions . Be­
cause of the ir construction (width, compo und,
tread pattern), summer t ires prov ide less traction
on ice and snow.
.., Use winte r tir es on all four whee ls .
.., Only use winter t ires that are approved for your
vehicle.
.., Please note that the maximum permitted
speed may be lower with winter tires
c:> .&,.
Your authorized Audi dealer or authorized re­
pai r facility can inform you about the maximum
permitted speed for your tires.
.., Check the tire pressure after installing wheels
c:> page 245.
The effectiveness of winter tires is reduced great­
ly when the tread is worn down to a depth of
0 .1S7 inch (4 mm). The characteristics of w inter
tires also decrease greatly as the tire ages, re ­
gardless of the remaining tread.
A WARNING
-Never dr ive faste r than the maximum per­
mitted speed for your t ires. This could cause
the tires to heat up too much . Th is increases
the risk of an accident because it can cause
the tire to burst .
250
-Always adapt your driving to the road and
traffic cond itions. Drive carefully and reduce
your speed on icy or slippery roads. Even
w inter t ires can lose traction on black ice.
@ For the sake of the environment
Reinstall summer tires at the appropriate
time, beca use they provide better handling
when roads are free of snow and ice. Summer
tires cause less road noise, tire wear and fuel
consumpt ion.
(D Tips
You can a lso use all season tires instead of
winter tires. Please note that in some coun­
tries where w inter t ires are required, only win­
ter tires with the
& symbol may be permit­
ted.
· Snow chains
Snow chains improve traction in the snow .
.., Only install snow chains on the rear wheels .
.., Check and correct the seating of the snow
chains if necessary after driving a few feet. Fol­
low the instruct ions from the manufacture r.
.., Note the maximum permitted speed when dr iv­
ing w ith snow chains . Do not exceed 30 mph
(SO km/h) .
Snow cha ins not onl y improve the
driving in w in­
ter road conditions , but also the
braking .
Use of snow chains is only permitted with certain
rim/tire combinations due to technical reasons .
Check with a n author ized Audi dealer or author­
iz ed repair facility to see if you may use snow
c hains.
Use
fine-mesh snow chains. They must not add
more than 0.53 inch (13.5 mm) in he ight, includ­
i ng the cha in lock.
You must remove the chains when driving on
roads that are
free of snow. When roads are free
of snow , snow cha ins can impair hand ling and
damage the tires, and the chains will quick ly be
destroyed. .,.

Emergency assistance
"' Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel bolts
slightly.
"'Remove the alignment pin and insert and tight­
en the remaining wheel bolt slightly like the
rest.
"'T urn the jack handle* counter-clockwise to low­
er the vehicle until the jack* is fully released .
"'U se the whee l bolt wrench to tighten all wheel
bolts firmly¢
page 261. Tighten them cross­
wise,
from one bolt to the (approximately) op­
posite one, to keep the wheel centered.
@ Note
When removing or installing the wheel, the
r im could hit the brake rotor and damage the
rotor. Work carefu lly and have a second per­
son help you.
(D Tips
Never use the hexagonal socket in the handle
of the screwdriver to loosen or tighten the
wheel bolts.
- Pull the reversib le blade from the screwdriv­
er before you use the hexagonal socket in
the handle to turn the wheel bolts.
- When mounting tires with
unidirectional
tread design
make sure the tread pattern is
pointed the right way
¢page 264.
-The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of bot h the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When us ing a spare tire w ith a tread pattern in­
tended for use in a specific direct ion, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire .
264
-If the spare tire has to be installed in the incor­
rect direction, use the spare tire only tempora ­
r il y since the tire w ill not be ab le to achieve its
optimum performance character istics with re­
gard to aquaplaning, noise and wear.
- We recommend that you pay part icu lar atten­
tion to th is fact during wet weather and that
you adjust your speed to match road condi­
tions.
- Replace the flat tire with a new one and have it
installed on your veh icle as soon as possible to
resto re the handling advantages of a unidirec­
tional tire.
Notes on wheel changing
Please read the information ¢ page 242, New
tires ar wheels
if you are going to use a spare tire
which is different from the tires on your vehicle .
After you change a tire:
- Check the tire pressure on the spare immedi­
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
105 ft lb (140 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds.
&_ WARNING
- If you are going to equ ip your vehi cle w ith
tires or rims which differ from those which
were factory installed, then be sure to read
the information ¢
page 242, New tires or
wheels .
-

Child restraints Dang er of using child rest raints in th e front
seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
153
System anchors . . . . . . . . . . . . . . . . . . . . . 184
Where can I get additional information
about child restraints and their use? . . . .
189
Child saf ety . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Important safety instructions for using child
safety seats . . . . . . . . . . . . . . . . . . . . . . . .
17 5
Inst alling a child restraint using the LATCH
system
186
Mounting and releasing the anchorage
hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
186
Tether anchors . . . . . . . . . . . . . . . . . . . . . . 187
Tether straps . . . . . . . . . . . . . . . . . . . . . . . 187
Child safety locks
Rear doors . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Child saf ety seats
Booster seats . . . . . . . . . . . . . . . . . . . . . . .
180
Convertible child seats . . . . . . . . . . . . . . . 178
Danger of using child restraints in the front
seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
153
H ow do I properly install a child safety seat
. h' l 7 1nm yve1ce ...... .... ... .... .. .. .. . 175
Infant seats . . . . . . . . . . . . . . . . . . . . . . . . 177
LA TCH system . . . . . . . . . . . . . . . . . . . . . . . 186
Lower anchorages . . . . . . . . . . . . . . . . . . . 185
Safety instructions . . . . . . . . . . . . . . . . . . . 17 5
Unused safety belts on the rear s eat . . . .
177
Ch ild seats .. .. ............. .. .. .. .. . 177
Secur ing . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Cigarette lighter . . . . . . . . . . . . . . . . . . . . . . . 76
C leaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Cleaning/remov ing ice from windows . . . . . 2 10
Cleaning Alcantar a ......... .... .. .. .. . 211
C leaning artific ial leather. . . . . . . . . . . . . . . 211
Cleaning carbon parts .. .. .. .. .. .. . 210 ,211
C leaning controls .......... .... .. .. .. . 210
C lean ing decorative parts and trim .. .. .. . 210
Cleaning displays . . . . . . . . . . . . . . . . . . . . . 210
C leaning exhaust tail pip es . . . . . . . . . . . . . 209
Clean ing plast ic parts ....... .. .. .. .. .. . 210
Cleaning rims . . . . . . . . . . . . . . . . . . . . . . . . 209
;::J C leaning textiles .............. ... .. .. . 211
co
~ Climate control
~ Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 1.1'1 A t t· . l . ~ u oma 1c rec1rcu at1on . . . . . . . . . . . . . . . . 82 ,....,
Index
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Supplementary . . . . . . . . . . . . . . . . . . . . . . 83
Synchroni zing . . . . . . . . . . . . . . . . . . . . . . . . 82
Climate control system . . . . . . . . . . . . . . . . . 80
Climatized cupholder . . . . . . . . . . . . . . . . . . . 75
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Closing
Panoramic slid ing sunroof . . . . . . . . . . . . . .
47
Coat hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Compass mirror . . . . . . . . . . . . . . . . . . . . . . . 61
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 284
Consumer information . . . . . . . . . . . . . . . . . 281
Consumer Information . . . . . . . . . . . . . . . . . 142
Contacting NHTSA . . . . . . . . . . . . . . . . . . . . 142
Convenience
Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Convenience key . . . . . . . . . . . . . . . . . . . . . . . 40
Indicator lights . . . . . . . . . . . . . . . . . . . . . . 88
Locking and unlocking vehicle . . . . . . . . . . . 40
Starting engine (START ENGINE STOP but-
ton) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
Stopping the engine (S TAR T E NGINE STOP
button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
88
Switching on ignition . . . . . . . . . . . . . . . . . . 87
Convertib le child s afety seats . . . . . . . . . . . 178
Convertible locking retractor
Activating . . . . . . . . . . . . . . . . . . . . . . . . . .
183
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . 184
Using to secure a child safety seat . . . . . . 183
Coolant system . . . . . . . . . . . . . . . . . . . . . . . 227
Cooled cupholder . . . . . . . . . . . . . . . . . . . . . . 75
Cooling box in glove compartment . . . . . . . . 78
Cooling mode (climate control) . . . . . . . . . . . 81
Cooling System
Expansion t ank . . . . . . . . . . . . . . . . . . . . . .
227
Cornering light . . . . . . . . . . . . . . . . . . . . . . . . 54
Cruise control Changing speed . . . . . . . . . . . . . . . . . . . . . . 96
Preselect speed . . . . . . . . . . . . . . . . . . . . . . 96
Switching off . . . . . . . . . . . . . . . . . . . . . . . . 96
Switching on . . . . . . . . . . . . . . . . . . . . . . . . . 95
Warning/ indicator lights . . . . . . . . . . . . . . .
17
Cruising range . . . . . . . . . . . . . . . . . . . . . . . . . 22
287