2015 AUDI A8 battery

24 2 Ch ecking and filling
-Never charge a frozen or a thawed-out
battery. It could explode! If a battery has
frozen, then it must be replaced. A dis­
charged battery can freeze over at 32 °F
(0 °C) .
- Make sure the vent hose is always attach­
ed to the opening on the side of the bat­
tery .
- Never use batteries which are damaged .
There is the dange r of an explosion! Al­
ways replace a damaged battery .
A WARNING
California Proposition 65 Warning:
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive problems. Wash hands after han­
dling.
- Do not d isconnect the veh icle battery
when the ignition is on or when the en­
gine is running, otherwise, you will dam­
age electronic components in the electri­
ca l system.
- If your veh icle is go ing to stand for a
l ong period of time without being driven,
protect the battery from "freezing", oth­
erwise it w ill be damaged and w ill then
have to be replaced.
Battery charging
Starting the engine requires a well charged
battery.
Fig. 2 06 Engine compartme nt: connecto rs fo r a cha rg ­
e r and jump star t cab les
Alwa ys re ad and h eed all WARNINGS below
¢
A and ¢ A in Working on the battery on
page
241.
.. Switch off the ignition and all electrical con­
sumers .
.. Make sure the area is we ll ventilated when
you charge t he battery.
.. Open the eng ine hood ¢
page 228.
.. Remove the cover (D by pressing on the ar­
row ¢
fig. 206 .
.. Open the cover @on the pos it ive terminal.
.. Connect the charger connectors according to
the inst ructions to the
jump start b olt s.
(Bolts under the red cover = "posit ive", Bo lts
w ith hex head= "negative") .
.. On ly now plug the mains lead for the charg ­
ing equipment into the wal l o utlet and turn
iton ¢
,&.
.. M ake sure the cha rging rate is not over
3 0 amps /14.8 Volt .
.. When the battery is fully charged: Turn the
charg ing equipment off and remove the
mains lead from the wall out let .
.. Now remove the clamps for the charging
equ ipment.
.. Close the red cover on the positive pole .
.. Close the hood ¢
page 229.
A discharged battery can freeze at tempera ­
tu res of only 32 F
0 (0 °C). Allow a frozen bat­
te ry to thaw completely before attempting to
charge it¢ & . However, we recommend not
us ing a thawed battery again because the bat­
tery casing can be cracked due to ice forma ­
t ion and can leak battery acid.
Battery cha rging (M ax imum charging rate
of 30 amp s/14.8 Volt )
When charg ing at low vo ltages (e.g. with a
t rickle cha rge r), the battery cables do not
have to be disconnected first. The battery
caps should
not be opened when charg ing a
battery.
It is not necessary to remove the battery from
the luggage compartment, and it is also not
necessary to d isconnect the cab les .

.... N .... N
0 J:
'SI: .... \!) 1.1"1
.... 1.1"1 ,....,
Fa st charging the b att ery (charging rate
abo ve 14.8 Vo lt s)
Fo r technical reasons do not use a batt ery
charger that uses vo ltage g reater than 14.8
Volts to charge your vehicle's battery.
A WARNING
-
Charging a battery can be dangerous.
- Always follow the operating instructions
provided by the battery charger manu­
facturer when charging your battery.
- Never charge a fro zen battery. It may ex­
plode because of gas trapped in the ice.
Allow a frozen battery to thaw out first .
- Do not reuse batteries which were fro­
zen. The battery housing may have
cracked and weakened when the battery
froze .
- Charge the battery in a well ventilated
area . Keep away from open flame or elec­
trical spark . Do not smoke . Hydrogen gas
gene rated by the battery is exp losive.
- To reduce the danger of explosion , never
co nnect or disconnect cha rger cables
wh ile the charger is operating.
- Fast charg ing a battery is dangerous and
should only be attempted by a compe­
t ent technicia n w ith the proper eq uip­
ment.
- Battery a cid that may spill d uring charg­
ing should be washed off wit h a solution
of warm wa ter and ba king soda to neu ­
tralize the acid .
CD Note
Never use a fast charge r as a booster to
s tart the engine. This will se rio usly d am­
age sensitive elect ronic components, such
as control units, relays, radio, etc., as we ll
as the battery charger .
Checking and fillin g
Battery replacement
The new battery must have the same specifi­
cations and dimensions as the original equip­
ment battery.
In telligen t energy managemen t in your vehi­
cle is responsible for distributing the electri ­
cal ene rgy throughout your vehicle
¢ page 202. The intelligent energy manage­
ment system will keep the engine battery
c h arged better than vehicles without this sys ­
tem. To make sure the additional electrica l en ­
ergy is avai lab le once again afte r yo u have
changed the battery, we recommend that you
insta ll batteries of the same type and m anu­
facture only (the same as those installed at
the time your ve hicle was delivered) . Specif i­
cat ions are listed on the battery housing . Your
authorized dea le r must code the battery in
the energy management system to enab le you
to use the ene rgy manageme nt func tions cor ­
re ct ly afte r replacing the battery.
The new battery must have the same capacity,
vo ltage
( 1 2 volts), amperage, const ruction
and plug seal ing .
When installing the battery, make sure the ig­ nition and a ll elect rical consume rs are switch­
ed off .
CD Note
- Make sure the ventilation hose on the
side of the battery is connected, other­
w ise fumes or battery a cid ca n leak out .
- Veh icles with the Start-Stop-System* are
e quipped with a spec ial cycle-p roof AGM
battery. Install ing a d iffe rent type of
ba ttery c an cause problems in the vehi ­
cle e lectrical system. Whe n replacing the
vehicle battery, always install one w ith
the same specifications as the origina l
battery.
- Battery mounts and clamps must a lways
be sec ured correct ly .
- Read and fo llow the wa rnings under
¢ page 241, Working on the battery be-
fore per forming any work on the battery . ..,_
243
•
•

244 Checking and filling
@ For the sake of the environment
Because of the problem of proper disposa l
of a battery, we recommend your author­
ized Audi dealer change the battery for
you. Batter ies contain sulfuric acid and
lead and must always be disposed of prop­
erly in compliance w ith all environmental
regu lations . D isposing of vehicle batteries
improperly is very dangerous to the envi­ ronmen t.
Windshield/headlight
washer container
Fig. 207 Engine compartment: cover on the windshield
was her flui d reservo ir
The washer fluid container is marked with the
symbol~ on its cap
c::> fig. 207, c::> page 230 .
.. Before you check anyth ing in the engine
compartment,
always read and heed all
WARNINGS c::> A in Working in the engine
compartment on page 228 .
.. lift the filler cap tongue to add washer flu­
id . You can fill the container to the top .
.. Press the cap back onto the filler neck after
filling the container.
You can find the reservoir
capacity in the table
in
c::>page 288.
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on
washer jets. Always add a glass cleaner solu­
tion (with frost protection in the winter).
(D Note
Do not mix engine coolant antifreeze or
any other additives to fill up the wind­
shield washer reservoir.

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
Tires and wheels 24 7
Gross Vehicle Weight Rating ("GVWR") Ply
means the maximum total loaded weight of
the vehicle .
Groove
means the space between two adjacent tread
ri bs.
Load rating (code)
means the maximum load that a tire is rated
to carry for a given inflat ion pressure . You
may not find this informat ion on all tires be­
cause it is not requ ired by law.
Maximum load rating
means the load rating for a t ire at the max i­
mum permissible inflation pressure for that
tire .
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accesso ry weight
(c) Vehicle capacity weight, and
(d) Production opt ions we ight
Maximum (permissible) inflation pressure
means the maximum co ld inf lation pressure
to which a tire may be inflated . Also called
"maximum inflation press ure."
Normal occupant weight
means 150 lbs . (68 kilograms) times the
number of occupants seated in the vehicle up
to the tota l seating capacity of your vehicle.
Occupant distribution
means distribution of occupants in a veh icle.
Outer diameter
means the overall diameter of an inflated new
tire .
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ­
ing e levations due to labeling, decorations, or
protective bands or ribs. means a layer of
rubber-coated parallel cords.
Production options weight
means the combined weight of those installed
regular production opt ions we ighing over 5
lbs. (2.3 kg) in excess of those standa rd items
which they replace, not previously considered
in curb weight or accessory weight, including
heavy duty brakes, ride levelers, roof rack,
heavy duty battery, and spec ial trim.
Radial ply tire
means a pneumatic tire in which the ply cords
that extend to the beads are laid at substan­
tially 90 degrees to the centerline of the
tread.
Recommended inflation pressure
see ~ page 246, Cold tire inflation pressure .
Reinforced tire
means a tire design to operate at higher loads
and at higher inflation pressures than t he cor­
responding standard tire. Reinforced tires
may be identified as "XL", "xl", "EXTRA LOAD",
or "RF" on the sidewal l.
Rim
means a metal support for a tire or a t ire and
tube assembly upo n which the tire beads are
seated .
Rim diamete r
means nominal diameter of the bead seat. If
you change your wheel s ize, you wi ll have to
purchase new tires to match the new r im di­
ameter .
Rim size designation
means rim diameter and width.
Rim width
means nominal distance between rim flanges.
Sidewall
means that portion of a t ire between the
tread and bead .
•
•

.... N .... N
0 J:
'SI: .... \!) ..,.,
.... ..,., ,....,
Emergency situations
General
This chapter i s intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Ve hicles w ith an au tomatic tra nsmission
cannot be started by pus hing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine shou ld fail to start because of a
discha rged o r wea k battery, the battery can be
connected to the battery o f
another vehicle,
using a
pair of jumper cables to start the en­
g ine.
Jumper cables
Use only jumper cables of sufficiently la rge
c ross section to carry the starter c urrent safe­
l y. Refer to the man ufacturer's specifications.
Use only jumper cables with
insulated te rm i­
na l clamps wh ic h are d istinctly marked:
plus(+) cable i n mos t cases co lore d red
minu s(-) cable
in most cases colored black .
A WARNING
Batterie s contain e lec tricity, ac id, an d gas.
A ny of these can cause ve ry ser io us or fatal
inju ry. Follow the instructions below f or
safe han dling of your veh icle's b attery .
- Alway s shield you r eyes and avoid lean­
ing over the bat te ry whenever possib le.
- A dis ch arged battery c an free ze at tem­
peratures ju st be low 32 °F ( 0 °C ). Befo re
Emergency situations 281
connecting a jumpe r cab le, you must
thaw the fr ozen battery c omp lete ly, ot h­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin. Fl ush any contacted area with
wate r immediately.
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batter ies genera te exp losive gas­
es. Keep spar ks, flame and lighted c iga ­
rettes away from batte ries.
- Do not try to jump start any ve hicle w ith
a low ac id leve l in the battery.
- The vo ltage of the booste r batte ry m ust
a lso have a 12-Vol t rating. T he capacity
(Ah) of the booster battery sho uld not be
lowe r tha n that of the discharged bat­
tery . Use of batte rie s of d iffe ren t voltage
or substantially diffe rent "Ah" rat ing
may c au se an exp losion and persona l in­
JU ry.
- N ever cha rge a fro zen battery. Gas trap­
pe d in the ice may cause a n ex plosion.
- Never cha rge or use a batte ry tha t h as
been fr ozen. T he battery case may have
be weakened.
- Us e of b atter ies of differe nt voltage or
sub stant ia lly diffe ren t ca pa city (Ah) ra t­
i ng may c ause an ex plosion an d injury .
Th e capac ity (Ah) of the booster bat tery
should not be lower than that of the dis ­
charged batte ry .
- Before you chec k any thing in the engine
compa rtment, always read and hee d all
WARNINGS¢
page 22 8.
(D Note
- App lyin g a higher vo ltage booster ba t­
t ery w ill cause expens ive damage to se n­
sit ive e lectronic com ponents, such as
cont ro l units, relays, rad io, etc.
- The re must be no electrical contact be­
tween the vehicles as ot herwise c urrent
co uld a lready start to f low as soon as the
p o sit ive(+) term inals a re connected. ..,. •
•

282 Emergency situations
@ Tips
-The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charging the
battery, never connect the negative
ground cable to the battery negative
post because the battery manager sys­
tem must be able to detect the battery's
state of charge . Always connect the neg­
ative ground cable to the negative
ground post of the battery manager con­
trol unit.
Use of jumper cables
Make sure to connect the jumper coble
clomps in exactly the order described below!
Fig . 235 Engine co mpartment: connecto rs fo r jump
star t cab les and c harg er
Fig. 236 Ju m p sta rt in g w it h the ba ttery of anot her ve ­
h icle :@ - booster battery, @-discharge d ve hicle bat­
tery
The procedure described below for connecting
jumper cables is intended to provide a jump
start for your vehicle.
Vehicle with discharged battery:
•Turnoff lights and accessories, move lever
of automatic transmission to N (Neutral) or
P (Park) and set parking brake.
Connect POSITIVE(+) to POSITIVE(+)
(red)
• Open the red cover on the pos itive terminal
¢ fig. 235 .
1. Connect one end of the red positive cable
on the
jump start bolt¢ fig. 236@ (bolt
under the red cover = "positive ") of the ve ­
hicle to be started @.
2. Connect the other end to the positive ter-
mina l@ of the booster battery@.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Connect one end of the black negative ca­
ble to the negat ive terminal @ of the
booster battery @.
4. Connect the other end to the
jump start
pin © (bolts with hex head bolt= "nega­
tive") of the vehicle to be started @.
Starting the engine
• Start the engine of the veh icle w ith the
booster battery@. Run the engine at a
moderate speed.
• Start engine with discharged vehicle battery
@ in the usual manner.
• If the engine fails to start, do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 second s and then try
aga in.
• With engine running, remove jumper cables
from both vehicles in the exact
reverse o r­
de r.
• Close the red cover on the positive term inal.
T he battery is vented to the outside to prevent
gases from entering the veh icle inter ior. Make
sure that the jumper clamps are well connect­
ed with their metal parts in full contact with
the battery terminals.
_& WARNING
To avoid serious personal injury and dam­
age to the vehicle, heed all warnings and
instructions of the jumper cable manufac­
turer. If in doubt, call for road service.
- Jumper cables must be long enough so
that the veh icles do not touch.
-

-When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the eng ine compart­
ment .
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS ¢
page 228.
(D Note
Improper hook-up of jumper cables can r u­
in the generator.
- Always connect POSITIVE( +) to POSI­
TIVE(+), and NEGATIVE(-) to NEGATIVE
( - ) gro und post of the battery manager
control unit .
- Check that all screw plugs on the battery
cells a re screwed in firmly . If not, tighten
pl ugs p rior to connecting clamp on nega ­
tive battery term inal.
- Please note that the procedure f or con­
nect ing a jump er cable as desc ribed
above appl ies spec ifically to the case of
you r vehi cle be ing jump started. When
you are giv ing a jump star t to an othe r ve­
hi cle, do
not connec t the negat ive (-) ca­
ble to the negat ive (-) terminal on the
discharged battery @¢
fig. 236. In ­
stead, securely connect the negative( -)
cable to e ithe r a solid metal component
that is firmly bolted to the engine block
or to the e ng ine block itse lf. If the bat­
te ry tha t is being charged does not vent
to the outside, escaping batte ry gas
could igni te and exp lode!
Emergency towing
with commercial tow truck
General hints
Your Audi requires special handling for tow ­
tng.
The follow ing information is to be used by
commercia l tow tr uck operators who know
h ow to ope rate thei r equipme nt safe ly.
Emergenc y situ ation s 283
-Ne ver tow your Audi. Towing will cause
damage to the engine and tran smission.
- Never wrap the safety chain s or w inch ca­
ble s around the brake lines.
- To prevent unnece ssary damage , your Audi
must be transported with a flat bed tru ck.
- To load the vehicle on to the fl at bed , use
the towing loop found in the vehicle tools
a nd attach to the front or rear anchora ge
¢ page 283 and ¢ page 284 .
_& WARNING
A vehicle being towed is not safe for pas ­
sengers. Never allow anyo ne to ride in a
vehicle be ing towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed.
Fig. 237 Fr ont bu mpe r: cove r
Fig. 238 Fr ont bu mpe r: sc rew ing in t he tow ing loop
-
The towing loop f its into the threaded hole lo ­
cated on the right s ide of the front bumpe r
and cove red by a sma ll cove r when not in use .
.. Remove the tow ing loop from the vehicle
too l kit .

296 Index
AUTO Automatic cl imat e control . ... ... ... .. 79
Automatic headlights ....... .. .... . . 46
Auto Lock 33
Automatic belt retractor . . . . . . . . . . . . . 146
Automatic climate control Air vents ... ................ ..... .. 80
Automatic recirculation .............. 81
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 79
Se tup . .. .. .. . .......... .. .. .... .. 81
Automatic climate control system synchronizing ................ .... .. 80
Automatic t ransmission ... .. .. .. .. .. . 114
Automatic transmission (tiptronic)
Eme rgency mode .............. .... 118
Kick-down . . . . . . . . . . . . . . . . . . . . . . . . 117
Manual shifting ........... ... .. ... 117
Parking lock emergency release . .... . 119
Selector lever posit ions ............. 114
Automatic wipers . . . . . . . . . . . . . . . . . . . . 53
Auto Safety Hotline ................ . 141
Average consumption ........... .. .. .. 25
Average speed . . . . . . . . . . . . . . . . . . . . . . . 25
Avoid damaging the vehicle ...... .... . 207
B
Batt ery . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Charging . ............... .. .. .... . 242
I mportant warnings ....... ... .. .. . 241
Loc ation ... ................ ..... . 241
low .. ... .................. ..... . 202
Replacing the battery ..... .. .. .. .. . 243
State of charge ........... .. .. .... . 202
Winter operation .................. 240
Working on the battery ............. 241
Before driving .............. ... .... . 133
Blended gasoline ........ .. .. .. .. .. . 220
Blower (automatic climate control) . . . . . . 80
Boost er seats .............. ... .... . 182
Brake assist : Post-collision ..... .. .. .. . 198
Brake fluid Changing the brake flui d ... .. .. .. .. . 239
Checking the brake fluid level . .. ..... 239
What is the correct brake fluid level? .. 239
What should I do if the brake fluid warn-
ing light comes on? ............... . 239 Brake system
Anti- lock braking system ............. 19
Brake assist system ................ 197
Brake booster ..................... 200
Brake fluid .... .. ............. .... 239
Brake fluid specifications for refill and re -
placement .. .. .. .. ..... ........ .. 239
Brake light defective . . . . . . . . . . . . . . . . 22
Brake pads .. .. . .. ............ .. .. 205
El ec tromechanical parking brake ...... 85
Fluid reservoir ... ................. 239
How does moisture or road salt affect the
brakes? ......... .. .............. . 199
Warning/indicator lights ........ .... . 14
Worn brake pads symbol . . . . . . . . . . . . . 20
braking guard Messages ..... .. .. .............. .. 99
Braking guard ..... ................ .. 92
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Break-in period .. .. ............. .. .. 205
Brake pads .. .. .. ...... .... .... ... 205
Tires 205
Bu lbs ..... ..... .. .. .............. . 280
C
California Proposition 65 Warning ... .. 229
Battery specific . . . . . . . . . . . . . . . . . . . 242
Capacities .. .. .. .. ............. .. .. 288
Engine oil ..... ... .............. .. 231
Carbon parts
Cleaning .................... 216,217
Car carrier Transporting your vehicle ........... 285
Care ... .. .. .. .. .. ............. .. .. 214
Cargo are a
refer to Luggage compartment ...... .
Catalytic converter
Center armrest 139
206
Cockpit ... .... .. ............. .... . 61
Rear
Central locking .. .................. . .
Emergency locking .......... ..... .. . 68
33
37
Certification .... .. ............. .... 293
Changi ng a wheel .. ... .......... .. .. 269
Ch . . 'l
angmg engine
01 ....••....•..... • 235