.... N .... N
0 J:
'SI: .... \!) 1.1"1
.... 1.1"1 ,....,
Fa st charging the b att ery (charging rate
abo ve 14.8 Vo lt s)
Fo r technical reasons do not use a batt ery
charger that uses vo ltage g reater than 14.8
Volts to charge your vehicle's battery.
A WARNING
-
Charging a battery can be dangerous.
- Always follow the operating instructions
provided by the battery charger manu
facturer when charging your battery.
- Never charge a fro zen battery. It may ex
plode because of gas trapped in the ice.
Allow a frozen battery to thaw out first .
- Do not reuse batteries which were fro
zen. The battery housing may have
cracked and weakened when the battery
froze .
- Charge the battery in a well ventilated
area . Keep away from open flame or elec
trical spark . Do not smoke . Hydrogen gas
gene rated by the battery is exp losive.
- To reduce the danger of explosion , never
co nnect or disconnect cha rger cables
wh ile the charger is operating.
- Fast charg ing a battery is dangerous and
should only be attempted by a compe
t ent technicia n w ith the proper eq uip
ment.
- Battery a cid that may spill d uring charg
ing should be washed off wit h a solution
of warm wa ter and ba king soda to neu
tralize the acid .
CD Note
Never use a fast charge r as a booster to
s tart the engine. This will se rio usly d am
age sensitive elect ronic components, such
as control units, relays, radio, etc., as we ll
as the battery charger .
Checking and fillin g
Battery replacement
The new battery must have the same specifi
cations and dimensions as the original equip
ment battery.
In telligen t energy managemen t in your vehi
cle is responsible for distributing the electri
cal ene rgy throughout your vehicle
¢ page 202. The intelligent energy manage
ment system will keep the engine battery
c h arged better than vehicles without this sys
tem. To make sure the additional electrica l en
ergy is avai lab le once again afte r yo u have
changed the battery, we recommend that you
insta ll batteries of the same type and m anu
facture only (the same as those installed at
the time your ve hicle was delivered) . Specif i
cat ions are listed on the battery housing . Your
authorized dea le r must code the battery in
the energy management system to enab le you
to use the ene rgy manageme nt func tions cor
re ct ly afte r replacing the battery.
The new battery must have the same capacity,
vo ltage
( 1 2 volts), amperage, const ruction
and plug seal ing .
When installing the battery, make sure the ig nition and a ll elect rical consume rs are switch
ed off .
CD Note
- Make sure the ventilation hose on the
side of the battery is connected, other
w ise fumes or battery a cid ca n leak out .
- Veh icles with the Start-Stop-System* are
e quipped with a spec ial cycle-p roof AGM
battery. Install ing a d iffe rent type of
ba ttery c an cause problems in the vehi
cle e lectrical system. Whe n replacing the
vehicle battery, always install one w ith
the same specifications as the origina l
battery.
- Battery mounts and clamps must a lways
be sec ured correct ly .
- Read and fo llow the wa rnings under
¢ page 241, Working on the battery be-
fore per forming any work on the battery . ..,_
243
•
•
244 Checking and filling
@ For the sake of the environment
Because of the problem of proper disposa l
of a battery, we recommend your author
ized Audi dealer change the battery for
you. Batter ies contain sulfuric acid and
lead and must always be disposed of prop
erly in compliance w ith all environmental
regu lations . D isposing of vehicle batteries
improperly is very dangerous to the envi ronmen t.
Windshield/headlight
washer container
Fig. 207 Engine compartment: cover on the windshield
was her flui d reservo ir
The washer fluid container is marked with the
symbol~ on its cap
c::> fig. 207, c::> page 230 .
.. Before you check anyth ing in the engine
compartment,
always read and heed all
WARNINGS c::> A in Working in the engine
compartment on page 228 .
.. lift the filler cap tongue to add washer flu
id . You can fill the container to the top .
.. Press the cap back onto the filler neck after
filling the container.
You can find the reservoir
capacity in the table
in
c::>page 288.
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on
washer jets. Always add a glass cleaner solu
tion (with frost protection in the winter).
(D Note
Do not mix engine coolant antifreeze or
any other additives to fill up the wind
shield washer reservoir.
,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Tires and wheels
Tires
General notes
Tires may be the least appreciated and most
abus ed parts of a motor vehicle .
Tires may be the least ap preciated and most
a b used parts of a motor vehicle . T ires are,
however, one of the most important parts of a
vehi cle, particularly considering the compara
tively small patch of rubber on eac h tire that
assures that a ll- important contact between
you, you r vehicle and the road.
Ma intaining the correct tire pressure, mak ing
sure that your vehicle and its tires do not have
to carry mo re weight than they can safe ly han
d le, avoiding damage from road ha za rds and
r eg ularly inspec ting t ires for damage i nclud
ing cuts, slashes irreg ular wear and ove ra ll
condition are the most important things that
you can do to he lp avoid s udden tire failure in
cluding tread separat ion and b lowouts.
Avoiding damage If you have to d rive ove r a curb or similar ob
stacle, drive very slow ly and as close as possi
b le at a right angle to the curb.
A lways keep chemicals incl ud ing grease, o il ,
gasoline and brake fluid off the t ires .
I nspect the t ires regularly for damage (cuts,
cracks or b listers, e tc.). Remove any fo reign
bod ies embedde d in the t reads.
Storing tires Mark t ires when you remove them to indicate
the direction of rotation . T his ensures you to
be ab le to mount them correctly when you re
in stall them .
When removed, the whee ls or t ires should be
sto red in a cool, d ry and preferably dark place .
Store tires in a vertical pos ition if they are not
mounted on r ims, in a horizontal pos it ion if
they are mounted on rims .
Tires an d wheel s 245
New tires
New tires h ave to be broken in ¢ & .
The tread depth of new t ires may va ry, accord
ing to the type a nd make of t ire and the tread
pa tte rn.
Hidden damage
Damage to tires and r ims is ofte n not readily
visible . If you notice unusual v ib rat io n or the
vehicle p ulls to one s ide, th is may ind icate
that one of the t ires has been damaged . T he
tir es m ust be che cked immed iate ly by an au
t horized Audi dea le r or q ua lified wor kshop .
Unidirectional tires
A un idirec tional tire can be identified by ar
rows on the s idewa ll, that po int in the direc
tion the t ire is desig ned to rotate. You mus t
f ol low the specified d irection o f rotation . T his
is necessary so that these tires can develop
their optimum characteristics regarding grip, road noise, wear and hydrop laning resistance.
For more information
¢ page 275.
A WARNING
New tires or t ires that are o ld, worn or
damaged can not provide maximum con
trol and braking ability .
-
-New tires tend to be slippery and must
be broken in. To reduce the r isk of losing
contro l, a co llision and ser ious personal
in ju ries, d rive with special ca re fo r the
fi rst 350 m iles ( 560 km).
- Driving with worn or damaged tires can
le ad to loss of control, sudde n tire fail
ure, including a blowout and sud den de
fla tion, c ras hes and se riou s personal in
juries . Have wo rn or d amaged t ires re
placed immediate ly.
- Ti res age even if they are no t being used
an d can fai l sudden ly, especially at hig h
spee ds. Tires that are more than 6 years
old can only be used in an emergency
and then w ith special care and at low
speed.
•
•
.... N .... N
0 J:
'SI: .... \!) er,
.... er, ......
vehicle with different rims/tires or you bought
the vehicle as a previously owned vehicle.
Remembe r, your safety and that of yo ur pas
sengers also depends on mak ing s ure that
l oad limits are not exceeded . Vehicle load in
cludes everybody and everything in and on the
veh icle. These load limits are technically refer
red to as the vehicle's Gross Vehicle Weight
Rating ("GVWR"). The Gross Axle Weight Rat
ing (''GAWR") is the maximum load that can
be appl ied at each of the veh icle's two axles .
The Gross Vehicle Weight Rating and the
Gross Axle We igh t Rating a re listed on the
safety compliance s ticker labe l located on the
d river's side 8-p illa r. T he tire pressure label on
your Audi lists the maximum combined weight of all of the occupants and luggage or
other cargo that the vehicle can carry. For the
locat ion of the tire pressure label¢
fig. 208.
A WARNING
Overloading a vehicle can cause loss of ve
hicle control, a cras h or other accident, se
rious personal inju ry, and even death .
-Carry ing more weight than your vehicle
was designed to carry will prevent the
vehicle from handling p roperly and in
cr ease the ris k of a loss of veh icle con
t ro l.
- T he bra kes on a veh icle that has been
overloaded may no t be able to stop t he
vehicle within a sa fe distance.
- T ires on a vehicle that has been ove rload
ed can fail suddenly causing loss of con
t ro l and a c rash.
- Always make sure that the tota l load be
ing t ransporte d -including the we igh t of
a tra iler hi tc h and the tongue weight o f a
loaded trailer -does not make the vehi
cle heavier t han the vehicle's Gross Vehi
cle Weight Rating.
A WARNING
- Incorrect tire pressures and/or underin flation can lead to a serious or fata l acci
dent .
-
Tire s an d wheel s 251
-Inco rrect tire pressures and/or unde rin
flation ca use increased tire wear and can
affect the handling of the vehicle .
- Incorrect tire pressures and/or underin
flation can a lso lead to sudden t ire fail
ure, including a blowout and sudden de
f lation, caus ing loss of veh icle control.
Checking tire pressure
The correct tire pressure for the tires original
ly installed on your vehicle is listed on the tire
pressure label located on driver's side 8-pil lar .
The recommended tire pressures are on the
tire pressure labe l and in the table
¢ page 249 , Cold tire inflation pressure. This
means that the pressure m ust be checked and
adjusted when the t ire has not been dr iven fo r
more than a couple of mile s (kilometers) a t
l ow speeds d uring the previous th ree ho urs.
Air in the tires expands when the tire hea ts up
as a result of interna l friction as it flexes in
u se . T he t ire pressure is higher when the tire
has warmed up than when it is "cold."
It is the inflation pressure in a "co ld" t ire that
counts . Therefore, you should never let air out
of a warm tire to match "Cold tire inflat ion
pressure" recommendat ions ¢
page 249 . The
tires would then be underinflated and co uld
fail suddenly .
The tire pressure label on your Audi lists the recommended co ld tire inflation pressures at
maximum capacity for the new, orig inal
equipment tires that were on your ve hicle at
the time it was manufactured. For the loca
tion of the label¢
page 249, fig . 208 .
Most tires lose air naturally over t ime . They
can a lso lose some air if you drive over a pot
ho le or hit a curb while park ing.
It is usually
not possible to see whether the rad ial tires
used today are under inflated just by loo kin g
at them.
T herefo re, be sure to check t ire pressu res at
least once a month and a lways before going
o n a long t rip. Ma ke su re to ta ke t he number ..,.
•
•
252 Tire s and wheel s
of people and the amount of luggage into ac
count when adjusting tire pressure for a trip -
even one that you would not consider to be
"long." See
c> page 2 53 , Tires and vehicle
load limits
for more importan t information.
A lways use an accurate tire pressure gauge
when checking and adjusting inflation pres
sures . Check all of the t ires and be sure not to
f orget the spare tire. If the pressure in any tire
is too high when the tire is "cold," let air out
of the t ire slowly with the edge of the tire
gauge and keep checking the pressure until
you reach the pressure that is cor rect for the
l oad (passenge rs and luggage) a nd kind of
d riving you plan to do.
If the p ress ure in any tire is too low, note the
d iffe rence between the pressure in the cold
tire and the pressure yo u need and add the a ir
that yo u need to reach the correct pressure for
the vehicle load (passengers and luggage) for
the tires on your vehicle as listed on the on
you r veh icle and in this manua l and the k ind
of dr iving you plan to do.
Never exceed the ma ximum infl ation pre s
sure li sted on the tire sidewall for any rea
son.
Remember that the vehicle manufacturer, not
the tire manufacture r, determines the correct
tire pressure for the tires on your vehicle.
It is important to check the tire pressu re when
the tires are cold .
- Read the requ ired t ire pressu re from the tire
pressure label. The tire pressu re labe l is lo
cated on the drive r's side 8-p illar.
- T urn the valve stem cap counter-clockwise
to remove it from the tire valve.
- Place the air pressu re ga uge on the valve .
- The tire pressures should only be checked
and adjusted when the tires a re cold. The
s li ghtly raised pressu res of warm tires must
not be reduced.
- Adjust the tire pressure to the load you are
carrying.
- Re install the valve stem cap on the valve .
When should I check the tire pressure?
The co rrect tire pressu re is especially impor
tant a t high speeds. The pressu re should
therefore be checked at least once a month
and always before sta rting a jo urney . Do not
forget to check the tire pressure for the spare
whee l
c> page 268 .
When should I adju st the tire pres sure s?
Adjust the tire pressure to the load you are
ca rrying . After cha ng ing a whee l
or replacing
whee ls you have to adjust the tire press ure s
on all whee ls. In addition, yo u m ust then
store the new tire pressures in t he tire pres
sure monitoring system*
c> page 263.
A WARNING
=
Incorrect tire pressures and/or underi nfla-
tion can lead sudden tire fa ilu re, loss of
control, collision , serio us pe rsonal injury
or even dea th.
- When the wa rn ing symbol
[IJ appears i n
the ins trument clus ter, stop and inspec t
the t ires.
- I nco rrect tire pressure a nd/or underinfla
tion c an cause increase d tire wea r and
can a ffect the hand ling of the vehicle and
stopping abi lity.
- I nco rrec t tire pressures an d/or underin
flation can a lso lead to s udden t ire fail
ure, including a blowout and sudden de
flation, ca using loss of vehicle contro l.
- The driver is responsible for the co rrect
tire pressures for all tires on the vehicle .
The applicable pressure values are locat
ed on a sticke r on the dr iver's s ide B-pil
lar.
- Only when all tires on the vehicle are fil
led to the correct pressure, the t ire pres
sure mon itor ing* system can work cor
rectly .
- The use of incorrect tire pressure va lues
can lead to acc idents or other damage .
Therefore it is essential that the drive r
observe the spec ified t ire pressu re val ues
for the tires and the correct pressures for
II),
254 Tires and wheels
A WARNING
Overloading a vehicle can cause loss of ve
hicle control, a crash or other accident, se
rious personal injury, and even death.
- Carrying more weight than your vehicle
was designed to carry will prevent the
vehicle from handling properly and in crease the risk of the loss of vehicle con
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
vehicle within a safe distance.
- Tires on a vehicle that has been overload
ed can fail suddenly, including a blowout
and sudden deflation, causing loss of
control and a crash.
- Always make sure that the total load be
ing transported -including the weight of
a trailer hitch and the tongue weight of a
loaded trailer -does not make the vehi
cle heavier than the vehicle's Gross Vehi
cle Weight Rating.
Determining correct load limit
Use the example below to cal
culate the total weight of the
passengers and luggage or oth
er things that you plan to trans
port so that you can make sure
that your vehicle will not be
overloaded.
Steps for Determining
Correct Load Limit
1. Locate the statement "THE
COMBINED WEIGHT OF OC
CUPANTS AND CARGO
SHOULD NEVER EXCEED XXX
KG OR XXX LBS" on your ve
hicle's placard (tire inflation pressure label)
¢ page 249,
fig. 208.
2.
Determine the combined
weight of the driver and pas
sengers that will be riding in
your vehicle.
3. Subtract the combined weight of the driver and pas
sengers from
"XXX" kilo
grams or
"XXX" pounds
shown on the sticker
c> page 249, fig. 208.
4. The resulting figure equals
the available amount of car
go and luggage load capaci
ty. For example, if the
"XXX"
amount equals 1400 lbs.
and there will be five 150
lbs. passengers in your vehi
cle, the amount of available
cargo and luggage load ca
pacity is 650 lbs. (1400-7 SO
(5
X 150) = 650 lbs.)
5. Determine the combined weight of luggage and cargo
being loaded on the vehicle.
That weight may not safely
exceed the available cargo
and luggage load capacity
calculated in Step 4.
6. If your vehicle will be towing
a trailer, load from your trail
er will be transferred to your .,.
256 Tires and wheels
Incorrect wheel alignment
Incorrect wheel alignment can cause exces
sive tire wear, impairing the safety of the vehi
cle. If tires show excessive wear, have the
wheel alignment checked by an authorized
Audi dealer or qualified workshop.
All Wheel Drive
Vehicles with quattro must always have tires
of the same size, construction and tread type.
For details see Qpage 202 .
.&_ WARNING
Sudden tire failure can lead to loss of con
trol, a crash and serious personal injury!
- Never drive a vehicle when the tread on
any tire is worn down to the wear indica
tors.
- Worn tires are a safety hazard, they do
not grip well on wet roads and increase
your risk of"hydroplaning" and loss of
control.
- Always keep chemicals that can cause
tire damage, such as grease, oil, gasoline
and brake fluid away from tires.
- Tires age even if they are not being used
and can fail suddenly, especially at high
speeds. Tires that are more than 6 years
old can only be used in an emergency
and then with special care and at lower speeds.
- Never mount used tires on your vehicle if
you are not sure of their "previous histo
ry." Old used tires may have been dam
aged even though the damage cannot be
seen that can lead to sudden tire failure
and loss of vehicle control.
New tires and replacing tires and wheels
New tires and wheels have to be broken in .
Fig. 212 Tir e specificat ion codes on the s idewall of a
t ire
No. Description
® Ratio of height to width (aspect ratio)
© Radial
® Rim diameter code
® Load index and speed rating
(J) U.S . DOT tire identification number
® Audi Original tire
® Sever snow conditions
@ Tire ply composition and materials
used
@ Maximum load rating
@ Treadwear, traction and temperature
grades
@ Maximum permissible inflation pres-
sure
The tires and rims are essential parts of the
vehicle's design . The tires and rims approved
by Audi are specially matched to the charac
teristics of the vehicle and can make a major .,..
258 Tires and wheels
T up to 118 mph (190 km/h)
U up to 124 mph (200 km/h)
H up to 130 mph (210 km/h)
V up to 149 mph (240 km/h)
1l
Z over 149 mph (240 km/h)ll
W up to 168 mph (270 km/h)ll
Y up to 186 mph (298 km/h)l)
Your veh icle is normally factory equipped with
tires, which possess excellent driving charac
teristics and give your Audi opt imum driving
comfort. An electronic speed limiter
c:> page 30 will normally prevent your vehicle
from going faster than the tire speed rating
c:> & .
U.S . DOT Tire Identification Number (TIN)
and tire manufacture date
This is the tire's "serial number". It begins
with the letters "DOT" and indicates that the
tire meets all federal standards. The next two
numbers or letters indicate the plant where it
was manufactured, and the last four numbers
r epresent the week and year of manufacture.
F or example, the numbers 2214 mean the tire
was produced in the 22nd week of 2014. The
other numbers are marketing codes that may
or may not be used by the tire manufacturer .
T his information is used to contact consumers
if a tire defect requires a recall.
Audi original tire
Tires with the identification "AO" or "RO" have
been specially matched with your Audi . We
recommend using only these tires because
they meet the highest standards regarding
safety and driving characteristics when used
correctly . Your authorized Audi dealer will
gladly provide you with more information .
Tire ply composition and materials used
The number of plies indicates the number of
layers of rubber-coated fabric in the tire. In
general, the greater the number of plies, the more weight a tire can support. Tire manufac -
ll F t· "t h .
o r ires w 1 a m ax im um spee d ca pabil ity ove r 149
mph (2 40 km/ h), ti re manufact urers sometimes use
the lett ers " ZR."
turers also must indicate the materials in the
tire, which include steel, nylon, polyester, and
others .
Maximum Load Rating
Th is number ind icates the max imum load in
kilograms and pounds that can be carried by
the tire .
Tire quality grading for treadwear,
traction , and temperature resistance
Tread wear, traction and tempera ture grades
c:>page 259.
Maximum Permissible Inflation Pressure
This number is the greatest amount of a ir
pressure that should ever be put in the tire
un der normal driv ing conditions .
_& WARNING
= -
- Using incorrect or unmatched tires and/
or wheels or improper tire and wheel
combinations can lead to loss of control
collision and serious personal injury.
'
- Always use tires, rims and whee l bolts
that meet the specifications of original factory-installed tires or other combina
tions that have been specifically ap
proved by the vehicle manufacturer.
- Tires age even if they are not being used
and can fail suddenly, especially at high
speeds. Tires that are more than 6 years
old can only be used in an emergency
and then w ith special care and at lower
speeds.
- Never mount used tires on your veh icle if
you are not sure of the ir "previous histo
ry." Old used tires may have been dam
aged even though the damage cannot be
seen that can lead to sudden tire fa ilure
and loss of vehicle control.
- All four whee ls must be fitted with radial
tires of the same type, size (rolling cir cumference) and the same tread pattern . ..,_