2015 AUDI A5 light

Checking and Filling
-If you get battery acid in your eyes or on
your skin, immediately rinse with cold wa­
ter for several minutes and get medical at­
tention .
- If you should ingest any battery acid, seek
medical attention immediately .
- Do not expose the battery to an open flame, electric sparks or an open light .
- Do not smoke .
- Do not interchange the positive and nega-
tive cables.
- When working on the battery , be sure not to
short-circuit the terminals with tools or oth­
er metal objects . This would cause the bat­
tery to heat up very quickly, which could lead to damage or explosion and personal
injury .
- When a battery is charged, it produces hy­
drogen gas which is explosive and could
cause personal injury.
- Always keep the battery well out of the
reach of children .
- Before work is done on the electrical sys­
tem, disconnect the negative ground cable .
- Before performing any work on the electri­ cal system, switch off the engine and igni­
tion as well as any electrical equipment. The negative cable on the battery must be dis­
connected. If you are just going to replace a
light bulb, then it is enough to switch off
the lights.
- Before disconnecting the battery, switch off
the anti-theft alarm system! Otherwise you
will set off the alarm.
- When disconnecting the battery, first dis­
connect the negative cable and then the
positive cable.
- Before reconnecting the battery, make sure
all electrical consumers are switched off. Re­
connect the positive cable first and then the
negative cable. Never interchange the ca­
bles -this could start a fire!
- Never charge a frozen or a thawed-out bat­
tery. It could explode! If a battery has fro ·
zen, then it must be replaced. A discharged
battery can freeze over at 32°F (0°C).
- Make sure the vent hose is always attached
to the opening on the side of the battery .
202
-Never use batteries which are damaged.
There is the danger of an explosion! Always
replace a damaged battery.
A WARNING
California Proposition 65 Warning:
- Battery posts, terminals and related acces­
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive problems .
Wash hands after handling .
(D Note
- Do not disconnect the vehicle battery when
the ignition is switched on or when the en­
gine is running, otherwise, you will damage
electronic components in the electrical sys­
tem .
-If your vehicle is going to stand for a long
period of time without being driven, protect
the battery from "freezing", otherwise it
will be damaged and will then have to be re­
placed .
Battery charging
Starting the engine requires a well charged bat­
tery.
Fig. 166 E n g in e compar tmen t: C on nectors fo r charger and
jump er cables
Always read and heed all WARNINGS below
9 A and ¢ A in Working on the battery on
page 201.
.,. Turn off the ignition and all electrical consum­
ers.
.,. Make sure the area is well ventilated when you
charge the battery.
Iii>-

Checking and Fill in g
th e e nergy management functions correctly after
replacing the battery.
If i t is not poss ible to use a battery of this type,
the new battery must have the same capacity,
voltage (12-vo lts), amperage, construct ion and
p lug sealing.
When insta lling the battery, make sure the igni­
tion and all elec trical consumers are t urned off.
CD Note
Make sure the ventilation hose on the s ide of
t he batte ry is connected, otherwise fumes or
bat tery ac id can leak out.
@ For the sake of the environment
Because of the problem of proper d isposa l of
a battery, we recommend your author ized
Audi dea le r change the battery for yo u. Ba t­
teries contain su lfuric acid and lead and must
always be disposed of properly in compliance
w ith all environmenta l reg ulations. D isposing
of vehicle batteries improperly is very danger­
ous to the environment.
Windshield/headlight* washer container
Fig. 167 Engine co mpa rtment : Cove r on th e w in d shiel d
an d h ead ligh t• was her fl uid container
The washer fluid containe r is marked with the
symbol
O on its cap ¢ fig . 167 , ¢page 193 ,
fig . 161 .
.,. Before you check anyth ing in the eng ine com­
partment , alw ays re ad and he ed all WARN·
I NGS
¢ ,& in Working in the engine comport­
ment on page 191 .
204
.,. Lift the filler cap tongue to add washer fluid.
Yo u can fill the container to the top.
.,. Press the cap back onto the filler neck after fill-
ing the container .
You can find the reservoir ca p acit y in the table in
~ page 242.
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on the
washer jets . Always add a g lass cleaner solution
(with frost protection in the winter) .
CD Note
Do not mix engine coolant antifreeze or any
other additives to fill up the windsh ield wash­
er reservoir.

Wheels
Wheels and Tires
General information
.,.Che ck your tires regularly for
damage (punctures, cuts, cracks
and bulges). Remove foreign ob­
jects from the tire tread.
.,. If driving over curbs or similar
obstacles, drive slowly and ap­
proach the curb at an angle.
.,.Have faulty tires or rims re­
placed immediately.
"'Protec t your tires from oil,
grease and fuel.
.,.Ma rk tires before removing
them so that the same running direction can be maintained if
they are reinstalled .
.,.Lay tires flat when storing and
store them in a cool, dry location
with as little exposure to light as
possible.
(D Note
-Please note that summer and
winter tires are designed for
the conditions that are typical
in those seasons. Audi recom­
mends using winter tires dur­
ing the winter months. Low
temperatures significantly de­ crease the elasticity of summ­
er tires, which affects traction
Wheels
and braking ability. If summer
tires are used in very cold tem­
peratures, cracks can form on
the tread bars, resulting in
permanent tire damage that
can cause loud driving noise
and unbalanced tires.
-Burnished, polished or
chromed rims must not be
used in winter driving condi­
tions. The surface of the rims
does not have sufficient corro­
sion protection for this and
could be permanently dam­
aged by road salt or similar
substances.
Tire designations
Fig. 168 T ir e designations on the sid e-
wall ,..
205

also reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and stop­
ping ability .
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire pressure telltale . When the system detects a
malfunct ion, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent veh icle start-ups as long as the mal­
function exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function properly.
Wheels
If the Tire Pressure Monitoring System
indicator appears
Appl ies to vehicles : wi th t ir e p ress ure mo nito rin g system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Fig. 172 Instrument cluster: i ndicator light with message
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread circumference
and vibration characteristics of the individual
tires .
If the pressure changes in one or more
tires, this is indicated in the instrument cluster
display with an indicator light
[I] and a message .
If only one tire is affected, the location of that
tire will be indicated .
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle ¢
page 224. The tire pressure moni­
toring system only monitors the tire pressure you have stored. Refer to the tire pressure label for
the recommended tire pressure for your vehicle
r=> page215, fig.171.
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if:
- the tire pressure in one or more tires is too low .
- the tire has structural damage.
- the tir e was replaced or the tire pressure was
changed and it was not stored ¢
page 224.
-the spare t ire* is installed.
Indicator lights
[I] Loss of pressure in at least one tire¢.& .
Check the tires and replace or repair if necessary .
liJJ,-
223

Wheels
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
c!) page 224.
mm (Tire Pressure Monitoring System) Tire pres­
sure: System malfunction!.
If m appears after
switching the ignition on or while driving and the
[I] i ndicator light in the instrument cluster
blinks for approximately one minute and then
stays on, there is system malfunction. Try to
store the correct tire pressures
c:> page 224 . If
the indicator light does turn off or turns on again
after a short period of time, drive to your author­
ized Audi dealer or qualified repair facility imme­
diately to have the malfunction corrected.
A WARNING
-If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure.
- The driver is responsible for maintaining the
correct tire pressure. You must check the
tire pressure regularly.
-Under certain conditions (such as a sporty
driving style, winter conditions or unpaved
roads), the tire pressure monitoring system
indicator may be delayed.
- Do not use run-flat tires on your vehicle. Us­
ing them when not permitted can lead to
vehicle damage or accidents.
(D Tips
- The tire pressure monitoring system can al­
so stop working when there is an ESC mal­
function.
- Using snow chains may result in a system
malfunction.
- The tires with the identification "AO" or
"RO"
c:> page 212 have been matched with
your Audi tire pressure monitoring system.
We recommend that you use these tires.
224
· Storing tire pressures
App lies to vehicles: wit h tire press ure mo nitor ing system
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­
tem .
.,. Make sure before storing that the tire pressures
of all four tires meet the spec ified values and
are adapted to the load
c!) page 215.
.,. Switch the ignition on.
.,. Select: the
I CARI function button > Tire pres­
sure monitoring
control button. Or
.,. Select: the
I CARI function button > Car Sys­
tems*
control button > Servicing & checks >
Tire pressure monitoring.
(D Tips
Do not store the tire pressures if snow chains
a re i nsta lied.

M N
0 l­oo
rl I.O
"' N
"' rl
Emergency assistance
Vehicle tool kit
The tools ore stored underneath the floor panel
in the luggage comportment.
Fig. 173 Luggage compartme nt: tool kit
When you need access to the veh icle tool kit or
jack*, you will need to take out the spare t ire*
and cover¢
page 225.
The vehicle tool kit includes:
- Hook for removing wheel covers*
- Plastic hook to remove wheel bolt covers*
- Alignment pin for changing the whee l
- Screwdriver w ith reversible blade
- Tool for chang ing light bulbs
- Reversible bit (reversible Torx bit for changing
light bulbs)
- Rod for jack
- Jack*
- Lug wrench
- Towing eye
Some of the vehicle items listed above are prov id­
ed on certain models only or are optional extras.
Before returning the jack* to its place, retract the
jack arm fu lly.
_& WARNING
- Never use the screw driver hex head to
t ighten whee l bolts, since the bolts cannot
attain the necessary tightening torque if you
use the hex head, potentially causing an ac­
cident.
- The factory-suppl ied jack is intended only
for your vehicle model. Under no c ircum­
stances should it be used to lift heavy
Emergen cy assistance
vehicles or other loads; you risk injuring
yourself.
- Never start the engine when the vehicle is
raised, which could cause an accident.
- Support the vehicle securely with appropri­
ate stands if work is to be performed under­
neath the vehicle; otherwise, there is a po­
tential risk for injury.
Space-saving spare tire
(compact spare tire)
Applies to vehicles: with space-saving spare tire
The spore tire/wheel is located in the luggage
comportment under the cargo floor cover. It is
intended for short-term use only.
Fig. 174 Spare tire
Removing the spare tire
.,. Lift the cargo floor by the p lastic handle
¢fig. 174.
.,. Hook the handle into the luggage compart­
ment weather strip.
., Turn the large screw ¢
fig. 174 counter-clock­
wise.
., Take out the spare ti re .
., Always store the vehicle tool kit, the jack*, and
the replaced tire in the luggage compartment
¢page 118.
.,. Unhook the cargo floor before closing the rear
lid.
Using the spare tire (compact spare tire)
The compact spare tire is only intended for emer­
gencies until you can reach a repa ir shop. Replace
it as quickly as possible with a standard wheel
and tire. ..,
225

M N
0 I-co
rl I.O
"' N
"' rl
the wheel diagona lly opposite the wheel be­
ing changed with the folding chocks or ot h­
er objects. When one front wheel is lifted
off the ground, placing the Automatic Trans­
mission in "P" (Pa rk) wi ll
not prevent the ve­
hicle from moving .
- Before you change a wheel, be sure the
ground is level and fi rm.
If necessary, use a
sturdy board under the jac k.
- Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment c::>
page 118 .
(D Note
If you are chang ing the wheel o n a steep in­
cline, use a rock or sim ila r object to block the
opposite whee l to prevent the vehicle from
moving.
@ Tips
Obey a ll laws.
Changing a wheel
When you change a wheel, follow the sequence
described below step -by -step and in exactly that
order.
1. Remove the decorati ve w heel co ver* or the
w he el bolt caps *. For more details see a lso
c::> page 22 7, Decorative wheel covers or
c::> page 228, Wheels with wheel bolt caps .
2. Loosen the whe el bolt s c::> page 228.
3. Lo cate the proper mo unti ng po int for the
jack and align the jack below tha t point
c::> page229.
4. Lift the car wit h the jack c::> page 229.
5. Remove the wheel with the flat tire and then
install the
spare t ire c::> page 230.
6 . Tighten all wheel bo lts light ly.
7 .
Low er the veh icle w ith the jack.
8 . Use the wheel bolt wrench and
firmly tighten
9.
all whee l bolts in a crissc ross pattern
c::> page 228.
Replace t he de corative wh ee l c over* or the
whe el bolt cap s*.
Em erg en cy ass is tan ce
A WARNING
-Always read and follow all WARNINGS and in-
formation
c::> .&. in Raising the vehicle on
page
229 and c::> page 231.
After changing a wheel
A wheel change is not complete without the do­
ing the following.
.. Always store the vehicle tool k it, the jack*, and
the replaced t ire in the luggage compartment
c::>page 118.
.. Check the tir e pr essure of the spare ti re as soon
as poss ible .
.. As soon as possib le, have the
tightening to r­
que s
on a ll whee l bolts checked wi th a torque
wrench . Th e cor rect tigh tening torque is 90 ft
lbs .
(120 Nm).
.. Have the flat tire
replaced as soon as possible.
@ Tips
- If you not ice tha t the wheel bo lts are cor­
roded and difficult to turn while changing a
tire, they should be replaced before you check the tightening torque.
- Dr ive at reduced speed until you have the
tightening torques checked .
Decorative wheel covers
Applies to vehicles: with decorative w heel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 1 75 Chang ing a w heel: re m ovi ng t he w heel cove r
227

M N
0 l­oo
rl I.O
"' N
"' rl
Raising the vehicle
The vehicle must be li~ed with the jack first be­
fore the wheel can be removed .
·- ·
Fig . 178 Sill panels: marking s
Fig . 179 S ill: posit ion ing the vehicl e jack
The location of the jack point is indicated by an
indentation on the underside of the vehicle
¢ fig. 178.
.,.. Activate the pa rkin g brake to prevent the vehi­
cle from rolling unintentionally .
.,.. Shift into
1st gea r on vehicles with manua l
transmission or move the selector lever to the P
pos ition on vehicles with automatic transmis­
sion.
.,.. Find the
marking (imprint) on the sill that is
nearest the wheel that w ill be changed
¢ fig . 178. Behind the marking, there is a lift­
ing point
on the sill for the vehicle jac k.
.,.. Turn the
veh icle jack loca ted under the lifting
point on the si ll to raise the jack until the jaw
r:=;, fig. 179 @ covers the notch on the vehicle
¢A ¢ 0 .
.,.. Align the vehicle jack so the jaw @covers the
notch and the base plate @ is flat on the floor.
The base plate @ must be
vertical under the
lifting point @.
Em erg en cy ass is tan ce
.,.. Insta ll the rod on the vehicle jack : Insert the
rod into the opening on the handwheel. Turn
the rod left or r ight to secure it.
.,.. Continue raising the jack with the rod unt il the
wheel lifts off the ground slightly .
Position the vehicle jack
onl y under the designat­
ed lifting points on the si ll
Q fig. 178. There is ex­
actly
one Location for each wheel. The jack m ust
not be posit ioned at any other location
c:> ,& ¢CI).
So ft g round under the jack can cause the vehicle
to s lip off the jack . Always place the jack on firm
ground. Use a flat, stable support if necessary.
Use a non-s lip surface such as a rubber mat on a
slipper y surfa ce such as tile .
A WARNING
= -
-You or your passengers could be injured
while changing a wheel if you do not fo llow
t hese safety precautions:
- Position the vehicle jack on ly at the desig ­
nated lifting points and align the jack.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi­
c ient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack .
Always provide a firm base for the jack on
the ground.
If necessary, use a sturdy
board under the jack.
- On hard, slippery su rface (such as t iles)
use a rubber mat or simi lar to prevent the
ja ck from slipp ing.
- To help prevent injury to yourself and your
passengers:
- Do not raise the vehicle until you are sure
the jack is secure ly engaged.
- Passengers must not remain in the veh icle
when it is jacked up .
- Make sure that passengers wait in a safe
place away from the vehicle and we ll away
from the road and traffic.
- Make sure jack pos ition is correct, adjust
as necessary and then contin ue to raise
the jack .
229