2015 AUDI A3 wheel

252 What do I do n ow ?
-Support the vehicle securely with ap ­
propriate stands if work is to be per ­
formed underneath the vehicle;
otherw ise, there is a potential risk for
in Jury .
- To help preven t injury to yourself and
your passengers:
- Do not raise the vehicle u nti l you a re
sure the jack is sec urely e ngaged .
- Passengers mus t not rema in in the ve­
h icle when it is jacked up .
- Ma ke sure that passengers wait in a
safe p lace away from the vehicle and
well away from the road and traffic.
- Make sure jack posi tion is co rrect, ad­
just as necess ary and then contin ue to
raise the jack .
- Changes in temperature or load can af­
fect the height of the vehicle .
0 Note
Do not lift the vehicle by the s ill. Pos ition
the vehicle ja ck only at the designated lift­
ing poi nts on the sill. Othe rwise, your vehi­
cle will be damaged .
Taking the wheel off/installing the spare
Follow these instructions s tep-by-step for
c hanging the wheel.
Fig . 172 Chang ing a w hee l: u sing th e screw driver ha n­
dl e (w it h th e bla de re mov ed) to t urn the bolts
Fig. 173 Ch ang ing a wheel : alignment p in in sid e th e
t op hole
After you have loos ened all wheel bo lts and
raised the vehicle off the ground, remove and
replace the wheel as follows :
Removing the wheel
.,. Use the hexagon al so cket in th e screwdri v­
er handle
to completely remove the top­
most whee l bolt and set it aside on a
clean
surfac e Q fig. 172 .
.,. Screw the threaded end of the al ignme nt
p in
from the tool k it hand-t ight into t he
empty bol t hole
Q fig . 173.
.,. Then remove the other wheel bolts as de ­
scr ibed above .
.,. Take off the whee l leaving the a lignment pin
in the bo lt ho le
Q (J) .
Putting on the comp act sp are wheel
.,. Lift the spare whee l and carefully slide it
over the alignment p in to guide it in place
Q (J) .
.,. Use the hexagonal socket i n the screwdriver
handle to screw in and tighten a ll whee l
bolts
slightly .
.,. Remove the alignment pin and insert and
tighten the rema ining whee l bolt slightly
like the rest .
.,. Turn the jack handle counter -clockwise to
lower the vehicle until the jack is fully re­
leased .
.,. Use the wheel bolt wrench to tighten all
wheel bo lts fi rmly
Q page 250 . Tighten
them
crosswise , from one bolt to the (ap­
proximately) opposite one, to keep the
wheel cente red.

(D Note
When removing or installing the wheel,
the rim could hit the bra ke rotor and dam­
age the rotor . W ork carefully and have a
second person help you.
N ever use the hexa gonal s ocket in the ha n­
d le of the screwdriver to loosen or t ighten
the wheel bolts .
- Pull the reversib le blade from the screw­
drive r before yo u use the hexagonal
socket in t he handle to t urn the whee l
bo lts .
- When mounting tires with
unid irectional
tread design
make s ure the tread pat­
te rn is poi nte d the r ight way
c:> pag e253 .
- The w heel bolts should be clea n and easy
to tu rn . Ch eck for dirt and corros ion on
the mat ing su rfaces of both the whee l
a nd th e hu b. Remove a ll dir t fro m these
s ur fa ces before remo unting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern poin ted in
t he right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a sp are tire w ith a tr ead p atte rn
i ntended fo r u se in a specific direc tion, p lease
note t he following:
- T he di rection of rotation is ma rked by an a r­
r ow on the side o f the tire.
- If th e spare t i re has to be installed in the in­
c orrec t direction, use the spa re tire only
tem por ari ly si nce the t ire will no t be able to
ac hieve its op timum perfo rmance character­
ist ics with rega rd to aquaplani ng, noise and
wea r.
- We recommend that you pay particular at ­
tent io n to this fact du ring wet weat he r and
that you adjust your speed to matc h road
condit ions .
What do I do now? 253
-Replace the flat t ire with a new one and
have it installed on your vehicle as soon as
possible to restore the han dling advantages
of a un idirectional tire.
Notes on wheel changing
Please read the i nfo rmation c:> page 236, New
tires and replacing tires and wh eels
if you a re
go ing to use a spare tire wh ich is different
from the ti res on you r vehicle.
After you cha nge a tire :
-Check the tire pressure on the spare imme­
diately after installation .
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer o r
a qualified service station.
- With steel and alloy wheel r ims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm ).
- If you notice that the wheel bolts are cor­
roded and diff icult to turn while changing
a tire, they should be replaced before you
check the tightening torque.
- Replace the flat tire w ith a new one and
have it installed on your vehicle as soon as
possible. Remount the whee l cover.
Until then , dr ive with e xtra care and at re­
duced speeds.
A WARNING
-
- I f you are going to e quip your ve hicle
wit h tires o r rims which differ from those
which were fac to ry inst alled, t hen be
s ure to read t he informa tion
c:> p age 2 36,
New tire s and repla cing tires a nd
wheels .
-Always make s ure th e d am age d wheel o r
eve n a fla t tire an d the jack an d too l ki t
are p rope rly secu red in the luggage com ­
pa rtment an d are not loose in the pas ­
senger compartment .
- In an accident or sudden maneuver they
co uld f ly forwa rd, inj uring a nyone in the
veh icle.
•
•
•

254 What do I do now?
-Always store damaged wheel, jac k and
tools secure ly in the luggage compart­
ment. Otherw ise, in an acc ident or sud­
den maneuver they cou ld fly forward,
causing injury to passenge rs in the vehi­
cle .

Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through.
Fig. 17 4 Steering column area: cover
Fig. 175 Left side of the engine compartment: fuse
cover
Fuses i n the interio r
The fuses are behind the cover in the steering
column area
¢fig. 174.
•Turnoff the ignition and the fai led e lectrical
equipment.
• Check the following table to see which fuse
belongs to the equipment¢
page 256.
• Remove the cover: ¢ fig. 174.
• Remove the plastic clip from the fuse panel
cover in the eng ine compartment
c;, fig. 175.
• Remove the blown fuse using the plast ic
clamp and replace the fuse with an ident ica l
new one.
• Install the cover .
Fuse s in th e en gine compar tmen t
•Turnoff the ignition and the failed electrical
equipment .
Fuse s and bulb s 255
• Check the fo llowing tab le to see which fuse
be longs to the equipment
c:;, page 257.
• Remove the fuse panel cover¢ fig. 175.
• Remove the plastic clip from the fuse pane l
cover
c;, fig. 175.
• Remove the blown fuse using the plastic
clamp and replace the fuse with an identical
new one .
The indiv idual circu its are protected by safety
fuses . The fuses are located under the steer ­
ing wheel beh ind a cover and in the left s ide of
the engine compartment .
.&_ WARNING
-
Do not repair fuses and never replace a
blown f use with one that has a hig her amp
rating. Th is can cause damage to the elec­
trica l system and a fire .
(D Note
-If there a re multiple fuse values in a cell
in the fo llow tables, for examp le
5/10/20, it is because of equipment -re ­
lated differences . Replace the burned
fuse with an identical new one.
- If a new f use should burn out again
shortly after you have installed it, have
the electrical system checked by your au­
thorized Aud i dealer or qualified repair
facility as soon as possible.
(!) Tips
- The following tab le does not list fuse lo­
cations that are not used .
- Some of the following tables on ly app ly
to in certain models or options.

256 Fuses and bulbs
Interior fuse assignment
No. Equipment Ampere
F14
Climate control system
30 blower
F15
Electronic steering column
10 lock
F16 MMI area 7.5
F17
Instrument cluster 5
F18
Rearv iew camera 7 .5
F19
Convince key system control
7.5 module, tank system
F23 Right exter ior lights 40
F24
Panorama sunroof 20/30
F25
Door/driver's side doors (for
30 example power windows)
F26 Seat heating 30
F27
Sound-amp lifier 30
F29
Interior lights 7.5
Fig. 176 Vehicle inte ri or : fuse assignment F31 Left exter ior lights 40
No . Equipment Ampere F32 Driver assista nce systems 7.5
F2
Seat adjustment 10 F33 Airbag 5
F4
MM controls, MMI compo-
7.5 nents
F5 Gateway 5
Button lighting, coils for
socket relays, interior sound,
F34 back-up light switch, tern-7.5
perature sensor, o il level
F6 Ant i-theft alarm system 5 sensor
Climate/heating control, se-
Diagnosis, headlight range
le ctor lever (automatic
F7 transmission), parking heat -10 F35
control system, air quality
10 sensor,
automat ic dimming
er, rear window heater relay
rearview mirror
coil
Diagnosis, electrical parking
F36
Right cornering light/ right
15 LED-headlight
F8
brake switch, light switch,
10 rain/light sensor, interior
lighting
F9
Steering column switch
1 module
F37
Left corner ing light/ left
15 LED-headlight
Door/front passenger's side
F39 doors (for example, power 30
windows)
Fl0 D isp lay 5
F40 Sockets 20
Fll
Reversible driver's safety
25 belt tensioners F41 Reversible front passenger 's
25 side safety belt tensioners
Fl2 MMI area 15/20
F42 Central locking buttons 40
Fl3
Adaptive dampers control
20 module
F43 Windsh ield washer system 30
F44
all wheel drive 15
F45
Power driver's side seat 15

262 Emergency situations
Front towing loop
Fig. 180 Right front bumper: removing the cove r
Fig. 181 Right front bumper: towing loop installed
The threaded opening for the towing loop is
located behind a cover on the right side of the
front bumper.
• Remov e the towing loop from the vehicle
tool kit¢
page 247.
• Press inward on the upper le~ side of the
cap to remove it from the bumper
¢fig . 180.
• Insert the towing loop in the threaded open­
ing until it stops¢
fig. 181 and tighten it
with a whee l wrench.
• After using, place the towing loop back in
the vehicle tool kit.
A WARNING
If you do not screw the towing loop com­
pletely, it cou ld come out of the threaded
hole while the vehicle is being towed caus­
ing damage to the vehicle and possible se­
r ious personal injury.
-
Rear towing loop
Fig. 182 Righ t rea r towing loop: cover
Fig. 183 Right rea r towing loop: towing loop installed
The towing loop threaded opening is located
in the right of the rear bumper cover under a
cover.
• Remove the towing loop from the vehicle
tool kit ¢
page 247.
• Press inward on the upper area -arrow-and
lift it upward from the
lower area¢ fig. 182.
• Insert the towing loop in the threaded open ­
ing until it stops ¢
fig. 183 and tighten it
w ith a wheel wrench .
• After using, p lace the towing loop back in
the vehicle tool kit.
Depending on the model, the shape of the
cover can vary.
.&_ WARNING
If you do not screw the towing loop com­
pletely, it could come ou t of the threaded
hole while the vehicle is being towed caus­
ing damage to the vehicle and possible se­
rious personal injury.
-

Technical data
Vehicle identification
F ig. 187 Veh icle Identificat ion Number (VlN) plate: lo·
cat ion on driver's side dash pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -llllll -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXX XXX XX X X XX
XXX
KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
EOA 7D5 4UB 6XM SSG SR W
2EH JOZ 1LB lAS
18A
3FC SMU 7Xl
FDA 9G3 OG7 OYH
OJF
TL6 3KA 8EH
UlA X98 027
l XW 803 908 824 D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413 502
1SA 7GB 01A 4GO
XX . X XX X XX X XXXX
Fig. 188 The vehicle identification label- in side the
l uggag e compartme nt
Vehicle Identification Number (VlN)
The Veh icle Identifica tion Number is located
in different p laces :
- under the w indshield on the driver's side
¢fig. 187.
- in the MMI: Select: !MENUI button> Sys­
tems
control button or Car systems > Serv­
i ce
& co ntrol > VIN number .
-on the vehicle identification label.
Technical data 265
Vehicle identification label
The vehicle identification label is located in
the luggage compartment in the spare wheel
well.
T he label¢
fig. 188 shows the following vehi­
cle data:
(D Vehicle Identification Number (VIN)
@ Vehicle type, engine output, transmission
® Engine and transmission code
© Paint number and interior
® Optional equipment numbers
The information of the veh icle identification
label can also be found in your Warranty
&
Maintenance booklet .
Safety compliance sticker
The safety compliance sticker is your assur­
ance that your new vehicle complies with all
applicable Federal Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured . You can find this
sticker on the door jamb on the driver's side.
It shows the month and year of production
and the vehicle ident ification number of your
vehicle (perforation) as well as the Gross Vehi­
cle Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine
hood release. The spark ignition system com­
plies with the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
door jamb on the driver's side.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
o il and coolant, plus maximum load, which in ­
cludes passenger we ight (150 lbs/68 kg per
II>--

26 6 Techni cal data
designated s eating position) and luggage
w eight ¢.&, .
Gross Axle W eight Rating
The Gross Axle Weight Rating is the maximum
l oad that can be applied at each axle of the
vehicle ¢Lr!, .
Vehicle cap acit y weight
The vehicle capac ity we ight (max . load) is list­
ed either on the dr iver's side B-pilla r or inside
the fuel filler flap.
_& WARNING
- T he actual Gross Axle Weight Rat ing at
the front and rear axles shou ld not ex­
ceed the permissible weights, and their
combination must not exceed the Gross
Vehicle Weight Rating .
Dimensions
The dimensions can vary depend ing on the
model and equipment.
Length
Width
W idth (ac ross m irrors)
Height (unloaded) a)
Turn ing circle d iameter
-
- Exceeding permissible weight ratings can
result in veh icle damage, acc idents and
personal injury.
(D Note
- The vehicle capacity weight figures apply
when the load is distributed evenly in the
vehicle (passengers and luggage). When
transport ing a heavy load in the luggage
compartment, carry the load as near to
the rear axle as poss ible so that the vehi­
cle's handling is not impaired .
- Do not exceed the maximum permissible axle loads or the maximum gross veh icle
we ight. Always remember that the vehi­
cle's handling w il l be affected by the ex­
tra load. Therefo re, adj ust your speed ac­
cordingly.
- Always observe local regulat ions .
in (mm)
175 .3 (4456)
in (mm) 70 .7 (1796)
in (mm) 77 .l (1960)
in (mm) 55 .7 (1416)
ft (m) 35.8 (10.9)
al The he igh t o f th e ve hicle depe nds o n the tire s and the s usp en sion .
When driving on poor roads, by curb s and on
s teep ramp s, make sure tha t low-lying compo­
nent s such as the spoiler and exhaust sy stem
Capacities
Fuel tank
Front whee l Drive
All wheel drive
Winds hield washer system do not
come into contact w ith these or they
could be dam aged. This applies espe cia lly
when the vehicle is fully loaded .
gal (liters) approx.
13.2 (50.0)
gal (lite rs) approx. 14.5 (55.0)
quarts (liters) approx. 3.2 (3.1)