2015 Alfa Romeo 4C lights

Warning lights on
displayWhat it means What to do
LUGGAGE COMPARTMENT OPEN
The symbol and the corresponding message are
shown on the display.
POSSIBLE ICE ON ROAD
The symbol and corresponding message appear
on the display when the outside temperature is
below or equal to 3°C.
IMPORTANT In the event of outside temperature
sensor failure, the digits that indicate the value are
replaced by dashes.
BRAKE LIGHTS FAILURE
The symbol and corresponding message appear
on the display if a fault is detected in the brake
lights.The fault may be caused by a blown bulb, a
blown protection fuse or an interruption of the
electrical connection.
PARKING SENSOR FAILURE
The symbol and corresponding message appear
on the display if there is a parking sensor failure.
DISPLAY OF SELECTED DRIVING MODE
(“Alfa DNA” system)
A letter (d, n, or a) corresponding to the active
driving mode (dynamic or race, normal, all
weather) and a dedicated message are shown on
the display.
88
KNOWING THE INSTRUMENT PANEL

LEVERS ON THE
STEERING WHEEL
These enable sequential gear shifting
fig. 77.
– steering wheel stalk "+(pulling stalk
towards driver, see fig. 78): engage
higher gear;
– steering wheel stalk "–(pulling stalk
towards driver, see fig. 78): engage
lower gear.The engagement of a lower (or higher)
gear is only permitted if the engine
rpm allow it.
STARTING THE CAR
To start the engine press the brake
pedal: the system engages neutral (N)
automatically.
After the starting procedure, 1st gear
(1) or reverse (R) can be engaged.
Irrespective of the mode selected
(AUTO/MANUAL), to engage 1st gear
or reverse (R), it is necessary to press
the brake pedal and press the1button
on the transmission control panel (or
the "+" steering wheel stalk) to engage
1st gear or theRbutton to engage
reverse.
When 1st gear is engaged, the system
sets itself toAUTOmode.
Neutral (N) can be engaged again by
pressing theNbutton with the brake
pedal pressed.
When the1,NorRbuttons are
pressed (or "+" steering wheel stalk is
operated) without pressing the brake
pedal, no gear change request is
implemented by the system.
IMPORTANT Reverse cannot be
engaged by pressing the "-" stalk on
the steering wheel.Important information
If starting is requested with a
transmission failure (see "Warning lights
and messages" paragraph), carry out
the “Delayed start-up” procedure: when
the key is turned to AVV for at least 7
seconds with brake pedal pressed, the
engine will be started. The system will
remain in “recovery” condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver's door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
Notes (concerning car
start-up)
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.
It is not possible to set off in a higher
gear than 1st: if this is attempted,
the display shows a dedicated
message.
77A0L0071
78A0L0072
108
STARTING AND DRIVING

DRIVING STYLE
Starting
Do not warm the engine with the car at
a standstill or at idle or high speed:
under these conditions the engine
warms up much more slowly, increasing
consumption and emissions. It is
therefore advisable to move off
immediately, slowly, avoiding high
speeds: in this way the engine will
warm up more quickly.
Unnecessary actions
Avoid accelerating when stopped at
traffic lights or before switching off the
engine. This action is absolutely
pointless and only increases
consumption and pollution.
Gear selection
Using a low gear for faster acceleration
increases consumption.
In the same way, improper use of a high
gear increases consumption,
emissions and engine wear.Max. speed
Fuel consumption increases
considerably with speed. Maintain a
constant speed, avoiding unnecessary
braking and acceleration, which cost
in terms of both fuel consumption and
emissions.
Acceleration
Accelerating violently will greatly affect
consumption and emissions: avoid
frequent and strong accelerations.
CONDITIONS OF USE
Cold starting
Short journeys and frequent cold starts
do not allow the engine to reach
optimum operating temperature.
This results in a significant increase in
consumption levels (from +15 to +30%
on the urban cycle) and emissions.
Traffic and road
conditions
Rather high consumption levels are
linked to situations with heavy traffic, for
instance when travelling in queues
with frequent use of the lower gears or
in cities with many traffic lights.Stops in traffic
During prolonged hold-ups (e.g. level
crossings) the engine should be
switched off.
112
STARTING AND DRIVING

WARNING
92) Indicate the presence of the
stationary car in accordance with
current regulations: hazard
warning lights, warning triangle,
etc. Those on board should get
out of the vehicle and wait for the
wheel to be repaired away from
the threat posed by the traffic.
If parked on a slope or rough
surface, chock the wheels with
wedges or other suitable devices
(for the correct procedure for
parking the car safely, refer to the
"Parking" paragraph in the
"Starting and driving" chapter).
93) Give the booklet to the
technicians who will be handling
the tyre that was treated using
the "Fix&Go automatic" kit.
94) A repair is not possible if the
wheel rim is damaged (groove
is deformed, causing air to
escape). Do not remove foreign
bodies (screws or nails) from the
tyre.95) Do not use the compressor for
more than 20 consecutive
minutes. Risk of overheating. The
kit is not suitable for definitive
repairs, so the repaired tyres may
only be used temporarily.
96) The bottle contains ethylene
glycol and latex: it may cause
an allergic reaction. It is harmful if
swallowed. Eye irritant. It may
cause sensitisation if inhaled or
on contact. Avoid contact with
eyes, skin and clothes. In the
event of contact, rinse
immediately with plenty of water.
If ingested, do not induce
vomiting. Rinse out your mouth,
drink large quantities of water and
seek immediate medical attention.
Keep out of the reach of children.
The product must not be used
by asthmatics. Do not inhale the
vapours during insertion and
suction. Call a doctor immediately
if allergic reactions are noted.
Store the bottle in its special
compartment, away from sources
of heat. The sealant has an expiry
date. Replace the bottle if the
sealant has expired.
97) Wear the protective gloves
provided with the kit.98) Apply the adhesive label where it
can be easily seen by the driver as
a reminder that the tyre has been
treated with the quick repair kit.
Drive carefully, especially on
corners. Do not exceed 80 km/h.
Avoid sudden acceleration or
braking.
99) If the pressure has fallen below
1.8 bar, do not drive any further:
the Fix&Go automatic quick tyre
repair kit cannot guarantee proper
hold because the tyre is too
damaged. Contact a dedicated
Alfa Romeo Dealership.
100) Always indicate that the tyre
was repaired using the quick
tyre repair kit. Give the booklet to
the personnel charged with
handling the tyre treated with the
repair kit.
121

WARNING
101) The space-saver wheel (for
versions/markets, where
provided) is specific to your car,
do not use it on other models,
or use the space-saver wheel of
other models on your car. The
space-saver wheel must only be
used in the event of emergency. It
must only be used for the
distance necessary to reach a
service point and the car speed
must not exceed 80 km/h. The
space-saver wheel has an orange
label that summarises the main
cautions for use and limitations.
Never remove or cover the label.
The following information is
provided in four languages on the
label: "Important! For temporary
use only! 80 km/h max! Replace
with a standard wheel as soon as
possible. Never cover this
indication."102) Use your hazard lights, warning
triangle, etc to show that your car
is stationary. Passengers should
get out of the car and wait for the
wheel to be changed away from
the traffic. In the event of a wheel
change on a slope or on
unsurfaced roads, chock the
wheels.
103) Car handling is modified with
the space-saver wheel fitted.
Avoid violent acceleration and
braking, abrupt steering and fast
cornering. The overall duration
of the space-saver wheel is of
about 3000 km, after which the
relevant tyre must be replaced
with another one of the same
type. Never install a standard tyre
on a rim that is designed for use
with a space-saver wheel. Have
the wheel repaired and refitted as
soon as possible. Using two or
more space-saver wheels at the
same time is forbidden. Do not
grease the stud bolt threads
before you fit them, because they
could suddenly come loose.104) Use the jack only to replace
wheels on the car with which it
is supplied or on other cars of the
same model. Never use the jack
for other purposes, such as lifting
other car models. Never use it
for repair operations under the
car. Incorrectly positioning the
jack may cause the car to fall. Do
not use the jack for loads higher
than those shown on the label.
105) The space-saver wheel cannot
be fitted with snow chains.
IMPORTANT
14) Contact a dedicated Alfa Romeo
Dealership as soon as possible to
have the correct tightening of
the wheel stud bolts checked.
125

CHANGING A BULB
15)
106) 107) 108)
GENERAL
INSTRUCTIONS
❒Before changing a bulb check the
contacts for oxidation;
❒replace blown bulbs with others of
the same type and power;
❒after replacing a headlight bulb,
always check its alignment;
❒when a light is not working, check
that the corresponding fuse is intact
before changing the bulb. For the
location of fuses, refer to the
paragraph “If a fuse blows” in this
chapter.IMPORTANT
15) Halogen bulbs must be handled
by holding the metallic part only.
Touching the transparent part
of the bulb with your fingers may
reduce the intensity of the
emitted light and even reduce the
lifespan of the bulb. In the case
of accidental contact, rub the
lamp with a cloth and spirit and
leave to dry.
WARNING
106) Modifications or repairs to the
electric system that are not
carried out properly or do not take
the system technical
specifications into account can
cause malfunctions leading to the
risk of fire.
107) Halogen bulbs contain
pressurised gas; in the case of
breakage they may burst.108) Due to the high supply voltage,
gas discharge bulbs (Bi-Xenon)
should only be replaced by
specialised personnel: danger of
death! Contact a dedicated Alfa
Romeo Dealership.
IMPORTANT When the weather is cold
or damp or after heavy rain or washing,
the surface of headlights or rear lights,
may steam up and/or form drops of
condensation on the inside. This is
a natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside
of the glass which does not indicate a
fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when the
lights are turned on, starting from
the centre of the diffuser, extending
progressively towards the edges.
126
IN AN EMERGENCY

Bulbs Type Power Ref. Figure
Front side lights/Daytime running lights (DRL) LED - -
Rear side lights LED - -
Dipped/Main beam headlights (versions with
Bi-Halogen headlights) (for versions/markets,
where provided)H7 55 W D
Dipped/Main beam headlights (versions with
Bi-Xenon headlights) (for versions/markets, where
provided)D1S 35 W -
Dipped/Main beam headlights (versions with
Bi-LED headlights) (for versions/markets, where
provided)LED - -
Front direction indicators PY21W 21 W B
Rear direction indicators PY21W 21 W B
Side direction indicators WY5W 5 W A
Brake lights LED - -
3rd brake light LED - -
Number plate lights W5W 5 W A
Rear fog light W16W 16 W A
Reversing light W16W 16 W A
Roof light C10W 10 W C
Luggage compartment light W5W 5 W A
128
IN AN EMERGENCY

REPLACING
EXTERIOR BULBS
FRONT LIGHT CLUSTERS
These contain the bulbs for the side
lights/daytime running lights (DRL),
dipped beam headlights, main beam
headlights and direction indicators. The
bulbs are arranged as follows fig. 96:
ASide lights/daytime running lights
BDipped/main beam headlights
CDirection indicators
To replace the bulbs for the dipped and
main beam headlights and for the
direction indicators open the
corresponding protective flaps on the
inner wheel arch fig. 97 that can be
located by steering the wheel
completely.A - direction indicator bulb protective
flap
B - dipped/main beam headlight bulb
protective flap
Side lights/daytime
running lights (DRL)
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
Dipped/main beam
headlights
To change the bulb, proceed as follows:
❒steer the wheel completely;
❒open the protective flap B fig. 97 by
rotating the fixing screw;
❒take out the electric connector A fig.
98 and then rotate the bulb holder B
clockwise and remove it;
❒extract the bulb and replace it;❒refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector A;
❒close the protective flap B fig. 97.
Direction indicators
Front
To change the bulb, proceed as follows:
❒steer the wheel completely;
❒open the protective flap A fig. 97 by
rotating the fixing screw;
❒take out the electric connector A fig.
99 and then rotate the bulb holder B
clockwise and remove it;
❒extract the bulb and replace it;
❒refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector A;
96A0L0091
97A0L0092
98A0L0093
129
❒close the protective flap A fig. 97.