2014 YAMAHA YZ450F radiator

DESCRIPTION
1-4
EAS1SL1009
DESCRIPTION
TIP
Designs and specifications of the vehicle are subject to change without notice. Therefore, please
note that the descriptions in this manual may be different from those for the vehicle you have pur
-
chased.
1. Clutch lever10. Coolant drain bolt
2. Front brake lever11. Rear brake pedal
3. Throttle grip12. Air filter
4. Radiator cap13. Drive chain
5. Fuel tank cap14. Shift pedal
6. Engine stop switch15. Oil level check window
7. Fuel tank16. Starter knob/idle screw
8. Kickstarter lever17. Front fork
9. Radiator
2 1
6
78 954 3
11 10 17 16 15 14 1312

SPECIAL TOOLS
1-16
Radiator cap tester
90890-01325
Mityvac cooling system tester
kit
YU-24460-A
This tool is used to check the
radiator and the radiator cap.
Radiator cap tester adapter
90890-01352
Pressure tester adapter
YU-33984
This tool is used to check the
radiator and the radiator cap.
Steering nut wrench
90890-01403
Exhaust flange nut wrench
YU-A9472
This tool is used to remove or
tighten the steering nut.
Cap bolt wrench
90890-01500
YM-01500
This tool is used to remove or
tighten the base valve.
Cap bolt ring wrench
90890-01501
YM-01501
This tool is used to loosen or
tighten the damper assem
-
bly.
Fork seal driver
90890-01502
YM-A0948
This tool is used to install the
oil seal of the front fork.
Spoke nipple wrench (6–7)
90890-01521
YM-01521
This tool is used to tighten the
spoke.
Tool name/Part number How to use Illustration

ENGINE SPECIFICATIONS
2-2
EAS1SL1053
ENGINE SPECIFICATIONS
Engine
Engine type Liquid cooled 4-stroke, DOHC
Displacement 449 cm3
Cylinder arrangement Single cylinder
Bore  stroke 97.0  60.8 mm (3.82  2.39 in)
Compression ratio 12.50:1
Starting system Kickstarter
Fuel
Recommended fuel Premium unleaded gasoline only
Fuel tank capacity 7.5 L (1.98 US gal, 1.65 Imp.gal)
Engine oil
Lubrication system Wet sump
Recommended brand YAMALUBE
Type SAE 10W-30, SAE 10W-40, SAE 15W-40, 
SAE 20W-40 or SAE 20W-50
Recommended oil grade API service SG type or higher, 
JASO standard MA
Engine oil quantity
Quantity (disassembled) 0.95 L (1.00 US qt, 0.84 Imp.qt)
With oil filter element replacement 0.69 L (0.73 US qt, 0.61 Imp.qt)
Without oil filter element replacement 0.67 L (0.71 US qt, 0.59 Imp.qt)
Oil filter
Oil filter type Paper
Oil pump
Oil pump type Trochoid
Inner-rotor-to-outer-rotor-tip clearance Less than 0.150 mm (0.0059 in)
Limit 0.20 mm (0.0079 in)
Outer-rotor-to-oil-pump-housing clearance 0.13–0.18 mm (0.0051–0.0071 in)
Limit 0.24 mm (0.0094 in)
Oil-pump-housing-to-inner-and-outer-rotor 
clearance 0.06–0.11 mm (0.0024–0.0043 in)
Limit 0.17 mm (0.0067 in)
Cooling system
Radiator capacity (including all routes) 1.04 L (1.10 US qt, 0.92 Imp.qt)
Radiator capacity 0.57 L (0.60 US qt, 0.50 mp.qt)
Radiator cap opening pressure 108–137 kPa (1.08–1.37 kg/cm2 15.7–19.9 psi)
Radiator core
Width 112.6 mm (4.43 in)
Height 235.0 mm (9.25 in)
Depth 28.0 mm (1.10 in)
Water pump
Water pump type Single suction centrifugal pump
Spark plug
Manufacturer/model NGK/CR8E
Spark plug gap 0.7–0.8 mm (0.028–0.031 in)

TIGHTENING TORQUES
2-14
EAS1SL1057ENGINE TIGHTENING TORQUES
TIP
- marked portion shall be checked for torque tightening after break-in or before each race.
ITEMThread
sizeQ’tyTIGHTENING TORQUESRemarks
Camshaft cap boltM6810 Nm (1.0 m·kgf, 7.2 ft·lbf)
Cylinder head blind plugM12128 Nm (2.8 m·kgf, 20 ft·lbf)
Spark plugM10113 Nm (1.3 m·kgf, 9.4 ft·lbf)
Cylinder head stud bolt (exhaust
pipe)M637 Nm (0.7 m·kgf, 5.1 ft·lbf)
Cylinder head boltsM94See TIP.*1
Cylinder head boltsM6210 Nm (1.0 m·kgf, 7.2 ft·lbf)
Cylinder head cover boltM6310 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil passage plug (cylinder head)M8115 Nm (1.5 m·kgf, 11 ft·lbf)
Cylinder boltM6110 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil pressure check boltM6210 Nm (1.0 m·kgf, 7.2 ft·lbf)
Balancer weight plate screwM6310 Nm (1.0 m·kgf, 7.2 ft·lbf)
Balancer driven gear nutM14150 Nm (5.0 m·kgf, 36 ft·lbf)
Use a
lock
washer.
Balancer nutM10145 Nm (4.5 m·kgf, 33 ft·lbf)
Use a
lock
washer.
Timing chain guide stopper plate
(exhaust side)M6110 Nm (1.0 m·kgf, 7.2 ft·lbf)
Timing chain tensioner cap boltM616 Nm (0.6 m·kgf, 4.3 ft·lbf)
Timing chain tensioner boltM6210 Nm (1.0 m·kgf, 7.2 ft·lbf)
Coolant drain boltM6110 Nm (1.0 m·kgf, 7.2 ft·lbf)
Radiator hose clamp screwM681.5 Nm (0.15 m·kgf, 1.1 ft·lbf)
Radiator boltM6410 Nm (1.0 m·kgf, 7.2 ft·lbf)
Radiator pipe bolt M6110 Nm (1.0 m·kgf, 7.2 ft·lbf)
Radiator pipe joint bolt M6110 Nm (1.0 m·kgf, 7.2 ft·lbf)
Water pump housing cover boltM6410 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil pump boltM525 Nm (0.5 m·kgf, 3.6 ft·lbf)
Oil pump cover screwM412.0 Nm (0.20 m·kgf, 1.4 ft·lbf)
Oil strainer boltM6110 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil passage cover bolt (left crank-
case)M6110 Nm (1.0 m·kgf, 7.2 ft·lbf)
Throttle cable cover boltM513.5 Nm (0.35 m·kgf, 2.5 ft·lbf)
Throttle body joint boltM6210 Nm (1.0 m·kgf, 7.2 ft·lbf)
Throttle body joint clamp boltM513.0 Nm (0.30 m·kgf, 2.2 ft·lbf)
Air filter joint clamp boltM413.5 Nm (0.35 m·kgf, 2.5 ft·lbf)
Air filter case boltM637 Nm (0.7 m·kgf, 5.1 ft·lbf)
LT
M
LT
LT
LT

TIGHTENING TORQUES
2-20
TIP
1. First, tighten the lower ring nut approximately 38 Nm (3.8 m·kgf, 27 ft·lbf) by using the steering nut
wrench, then loosen the lower ring nut one turn.
2. Retighten the lower ring nut 7 Nm (0.7 m·kgf, 5.1 ft·lbf).
Drive chain support nutM627 Nm (0.7 m·kgf, 5.1 ft·lbf)
Drive chain guide boltM534.0 Nm (0.40 m·kgf, 2.9 ft·lbf)
Rear frame and left cover boltM627 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel tank bolt (front side)M627 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel tank bolt (rear side)M619 Nm (0.9 m·kgf, 6.5 ft·lbf)
Fuel tank bracket bolt (front side)M647 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel tank bracket bolt (rear side)M627 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel pump boltM564.0 Nm (0.40 m·kgf, 2.9 ft·lbf)
Fuel inlet pipe screwM523.4 Nm (0.34 m·kgf, 2.5 ft·lbf)
Fuel tank cap cover boltM624.0 Nm (0.40 m·kgf, 2.9 ft·lbf)
Seat set bracket and fuel tank screwM617 Nm (0.7 m·kgf, 5.1 ft·lbf)
Seat boltM8222 Nm (2.2 m·kgf, 16 ft·lbf)
Left side cover boltM617 Nm (0.7 m·kgf, 5.1 ft·lbf)
Right side cover boltM627 Nm (0.7 m·kgf, 5.1 ft·lbf)
Frame and air scoop boltM627 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel tank and air scoop boltM627 Nm (0.7 m·kgf, 5.1 ft·lbf)
Radiator guard and air scoop boltM647 Nm (0.7 m·kgf, 5.1 ft·lbf)
Front fender boltM6410 Nm (1.0 m·kgf, 7.2 ft·lbf)
Rear fender bolt (front side)M637 Nm (0.7 m·kgf, 5.1 ft·lbf)
Rear fender bolt (rear side)M6216 Nm (1.6 m·kgf, 12 ft·lbf)
Mud flap screw—21.3 Nm (0.13 m·kgf, 0.94 ft·lbf)
Number plate boltM617 Nm (0.7 m·kgf, 5.1 ft·lbf)
ITEMThread
sizeQ’ty TIGHTENING TORQUES Remarks

CABLE ROUTING DIAGRAM
2-34
1. Clutch cable
2. Throttle cable (pull)3. Throttle cable (return)
4. Cable holder
5. Engine stop switch lead6. Frame
7. Coupler for connecting optional part
8. Bracket9. Engine stop switch coupler
10. Rectifier/regulator coupler
11. Starter knob/idle screw12. Neutral switch lead
13. Crankcase cover
14. AC magneto lead15. Front engine bracket
16. Radiator hose
17. Coupler cover18. Rectifier/regulator lead
19. Tension arm
20. Main harness21. Tank rail
22. Radiator
23. Cylinder head breather hose24. Radiator breather hose
25. Down tube
26. Crankcase
A. Pass the engine stop switch lead between the
frame and the cable holder.
B. Pass the engine stop switch lead between the
coupler for connecting optional part and the
frame, where the main harness should face the
outside of the vehicle.
C. Insert the coupler for connecting optional part into
the connector, and fix it to the bracket.
D. Insert and fix the engine stop switch coupler to
the bracket.
E. Insert and fix the rectifier/regulator coupler to the
bracket.
F. Pass the AC magneto lead to the front of the ve-hicle beyond the starter knob/idle screw and to
the rear of the vehicle beyond the radiator. No
pinch is allowed between the radiator and the
tension arm.
G. 70 mm (2.76 in)
H. Bring the neutral switch lead into line with the
crankcase cover with no sag allowed.
I. Bring the AC magneto lead into line with the
clutch cable with no sag allowed.
J. Pass the neutral switch lead to the inside of the
front engine bracket (the side of the vehicle).
K. Clamp the clutch cable and the AC magneto lead
by the plastic locking tie. Regardless of the orien-tation of the lock on the plastic locking tie, cut the
end.
L. Pass the clutch cable with no downward sag al-lowed.
M. Bring the grommet of the clutch cable into contact
with the radiator hose, and pass it to the outside
of the neutral switch lead and the AC magneto
lead (the outside of the vehicle).
N. 40 mm (1.57 in)
O. Clamp the clutch cable, the AC magneto lead,
and the neutral switch lead by the plastic locking
tie. Make sure that they are clamped at the posi
-tioning tape in the clutch cable. Make the lock on
the plastic locking tie face the front of the vehicle,
and cut the end.
P. After connecting the neutral switch coupler, at-tach the coupler cover.Q. After connecting the AC magneto coupler, attach
the coupler cover.
R. Pass the rectifier/regulator lead to the inside of
the tension arm (the side of the vehicle).
S. Pass the main harness to the front of the radiator
hose (the front of the vehicle), and to the inside of
the clutch cable (the side of the vehicle).
T. Pass the engine stop switch lead between the
coupler for connecting optional part and the tank
rail, with the lead on the main harness side facing
the top of the vehicle.
U. Pass the radiator breather hose between the
down tubes.
V. Clamp the radiator breather hose, above the en-gine bracket (front). Clamp the lock on the plastic
tie with it located outside the vehicle, and face the
end toward the front of the vehicle.
W. Clamp the clutch cable at the front of the lead (the
front of the vehicle).
X. Make the lock on the plastic locking tie face the
front of the vehicle, and insert the projection into
the hole in the frame. Cut the end of the plastic
locking tie.

CABLE ROUTING DIAGRAM
2-36
1. Bracket
2. Condenser3. Coolant temperature sensor
4. Coupler cover
5. Intake air temperature sensor coupler6. Intake air temperature sensor coupler
7. Radiator hoses
8. Radiator breather hose9. Joint coupler
10. Plate
11. Tension arm12. Throttle position sensor lead
13. Ground lead
14. Throttle position sensor coupler15. Radiator breather hose
16. Cylinder head breather hose
17. Engine guard18. Crankcase
19. Fuel pump coupler
20. Fuel hose21. Condenser lead
22. Fuel pump lead
23. Condenser coupler24. Ground lead terminal
25. Fuel tank
26. Damper27. Rear frame
28. Main harness
A. Insert the condenser into the bracket as far as it
will go.
B. Attach the coupler cover to the coolant tempera-ture sensor coupler.
C. Pass the radiator breather hose to the inside of
the radiator hose (the side of the vehicle).
D. Insert and fix the joint coupler to the plate. After
fixing it, attach the cover.
E. Pass the throttle position sensor lead to the out-side of the tension arm (the outside of the vehi-cle).
F. After connecting the throttle position sensor cou-pler, attach the cover.
G. Pass the radiator breather hose to the outside of
the tension arm and the throttle position sensor
lead (the outside of the vehicle), and to the inside
of the radiator hose (the side of the vehicle).
H. Pass the protector of the cylinder head breather
hose until it touches the holder.
I. Pass the cylinder head breather hose between
the engine guard and the crankcase.
J. Install the end of the cylinder head breather hose
with it facing downward.
K. After connecting the fuel pump coupler, attach
the coupler cover.
L. 55 mm (2.17 in) (seat load receiver)
M. Clamp the fuel hose and the fuel pump lead by
the holder. Make sure that the painted part on the
fuel hose is clamped, and face the lock on the
clamp toward the rear top of the vehicle.
N. Do not install the plastic locking tie to the seat
load receiver.
O. Make the lock on the plastic locking tie face the
front of the vehicle, and make the end face the
bottom of the vehicle. Do not cut the end.
P. Install the ground lead terminal between the plate
and the bolt.
Q. DetentR. Fix the ground lead terminal to the detent in the
plate. For the ground lead terminal, either side
will do.
S. Insert the projection on the plastic locking tie into
the hole in the rear frame.
T. Clamp the painted part on the fuel hose by the
plastic clamp. Make the lock on the plastic clamp
face the bottom of the vehicle, and cut the end.

CABLE ROUTING DIAGRAM
2-40
1. Main harness
2. Radiator3. Throttle position sensor lead
4. Joint coupler
5. Intake air temperature sensor lead6. Intake air pressure sensor lead
7. Frame
8. Fuel hose9. High tension cord
10. Spark plug cap
11. Cylinder head cover12. Sub-wire harness
13. Injector coupler
14. Injector lead15. Throttle body
16. Air filter case
17. ECU18. Sub-wire harness coupler
A. Fix the main harness by the plastic clamp, and in-sert the projection of the plastic clamp into the
hole in the sheet metal of the radiator.
B. Insert the projection of the main harness into the
hole in the frame.
C. To the sub-wire harness
D. Pass the high tension cord above the fuel hose.
E. ±10°F. Install the spark plug cap with this facing the right
of the vehicle.
G. Push the spark plug cap home, where there shall
be no gap between it and the cylinder head cover.
H. Pass the injector lead to the top of the vehicle be-yond the fuel hose.I. Insert the coupler of the sub-wire harness into the
rib of the air filter case.
J. Pass the sub-wire harness between the ECU and
the air filter case.