2014 YAMAHA SR400 ECO mode

INSTRUMENT AND CONTROL FUNCTIONS
3-10
1
234
5
6
7
8
9
10
11
12
EAU59490
Fuel cockThe fuel cock regulates and filters the
fuel supply from the fuel pump to the
fuel injector.
The fuel cock has two positions:
ON
With the lever in this position, fuel will
be supplied to the engine. Normal oper-
ation is done with the lever in this posi-
tion. OFF
With the lever in this position, fuel will
not flow. Use this lever position when
performing certain maintenance work
or when storing the vehicle for a pro-
longed time.
EAU13651
KickstarterTo start the engine, fold out the kick-
starter lever, move it down lightly with
your foot until the gears engage, and
then push it down smoothly but force-
fully. This model is equipped with a pri-
mary kickstarter, allowing the engine to
be started in any gear if the clutch is
disengaged. However, shifting the
transmission into the neutral position
before starting is recommended.
1. Arrow mark positioned over “ON”
1
1. Arrow mark positioned over “OFF”
1
1. Kickstarter
1
2RD-9-E0.book 10 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

5-1
1
2
3
45
6
7
8
9
10
11
12
OPERATION AND IMPORTANT RIDING POINTS
EAU15952
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
WARNING
EWA10272
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accidentor injury.
EAU59360
TIPThis model is equipped with:
a lean angle sensor to stop the en-
gine in case of a turnover. In this
case, turn the key to “OFF” and
then to “ON”. Failing to do so will
prevent the engine from starting
even though the engine will crank
when pushing the kick starter lever
down.

an engine auto-stop system. The
engine stops automatically if left
idling for 20 minutes. If the engine
stops, simply push the kick starterlever down to restart the engine.
EAU59530
Starting the engineIn order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.

The transmission is in gear with
the clutch lever pulled and the sid-
estand up.
See page 3-13 for more informa-
tion.
1. Turn the key to “ON” and set the engine stop switch to “ ”.
The engine trouble warning light
and fuel level warning light should
come on for a few seconds, then
go off.
NOTICE
ECA16712
If the warning light does not come
on initially when the key is turned to
“ON”, or if the warning light remains
on, see page 3-2 for the warning lightcircuit check.
2. Shift the transmission into the neu- tral position. The neutral indicator
light should come on. If not, ask a
2RD-9-E0.book 1 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-15
1
2
3
4
56
7
8
9
10
11
12 Tire information
This motorcycle is equipped with tube
tires.
Tires age, even if they have not been
used or have only been used occasion-
ally. Cracking of the tread and sidewall
rubber, sometimes accompanied by
carcass deformation, is an evidence of
ageing. Old and aged tires shall be
checked by tire specialists to ascertain
their suitability for further use.
WARNING
EWA10462
The front and rear tires should be of
the same make and design, other-
wise the handling characteristics of
the vehicle may be different, whichcould lead to an accident.
After extensive tests, only the tires list-
ed below have been approved for this
model by Yamaha Motor Co., Ltd.
WARNING
EWA10572

Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the mo-
torcycle with excessively worn
tires decreases riding stability
and can lead to loss of control.

The replacement of all wheel-
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience.

It is not recommended to patch
a punctured tube. If unavoid-
able, however, patch the tube
very carefully and replace it as
soon as possible with a high-quality product.

Ride at moderate speeds after
changing a tire since the tire
surface must first be “broken
in” for it to develop its optimalcharacteristics.
Front tire:
Size:90/100-18M/C 54S
Manufacturer/model:
METZELER/ME77 Front
Rear tire: Size:
110/90-18M/C 61S
Manufacturer/model: METZELER/ME77
2RD-9-E0.book 15 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

8-1
1
2
3
4
5
6
78
9
10
11
12
SPECIFICATIONS
EAU5091H
Dimensions:Overall length: 2085 mm (82.1 in)
Overall width: 750 mm (29.5 in)
Overall height: 1095 mm (43.1 in)
Seat height:
785 mm (30.9 in)
Wheelbase: 1410 mm (55.5 in)
Ground clearance: 130 mm (5.1 in)
Minimum turning radius:
2400 mm (94.5 in)Weight:Curb weight:174 kg (384 lb)Engine:Engine type:Air cooled 4-stroke, SOHC
Cylinder arrangement: Single cylinder
Displacement:
399 cm
3
Bore  stroke:
87.0  67.2 mm (3.43  2.65 in)
Compression ratio: 8.50 : 1
Starting system:
Kickstarter
Lubrication system: Dry sump
Engine oil:Recommended brand:
YAMALUBE
Type: SAE 10W-30, 10W-40, 10W-50, 15W-40,
20W-40 or 20W-50
Recommended engine oil grade: API service SG type or higher, JASO stan-
dard MA
Engine oil quantity: Without oil filter element replacement:
2.00 L (2.11 US qt, 1.76 Imp.qt)
With oil filter element replacement: 2.10 L (2.22 US qt, 1.85 Imp.qt)Air filter:Air filter element:
Oil-coated paper elementFuel:Recommended fuel:Regular unleaded gasoline (Gasohol (E10)
acceptable) Fuel tank capacity:
12.0 L (3.17 US gal, 2.64 Imp.gal)
Fuel reserve amount:
2.2 L (0.58 US gal, 0.48 Imp.gal)
Fuel injection:Throttle body:ID mark: 2RD1 00Spark plug(s):Manufacturer/model:
NGK/BPR6ES
Spark plug gap: 0.7–0.8 mm (0.028–0.031 in)
Clutch type: Wet, multiple-discTransmission:Primary reduction ratio:2.567 (77/30)
Final drive: Chain
Secondary reduction ratio:
2.947 (56/19)
Transmission type: Constant mesh 5-speed
Operation: Left foot operation
Gear ratio:
1st: 2.357 (33/14)
2nd:
1.556 (28/18)
3rd: 1.190 (25/21)
–20 –10 0 1020 30 40 50 C
10 30 50 70 90 110
0 130 F
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40SAE 10W-50
2RD-9-E0.book 1 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

9-1
1
2
3
4
5
6
7
8910
11
12
CONSUMER INFORMATION
EAU53562
Identification numbersRecord the vehicle identification num-
ber, engine serial number, and the
model label information in the spaces
provided below. These identification
numbers are needed when registering
the vehicle with the authorities in your
area and when ordering spare parts
from a Yamaha dealer.
VEHICLE IDENTIFICATION
NUMBER:
ENGINE SERIAL NUMBER:
MODEL LABEL INFORMATION:
EAU26401
Vehicle identification number
The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.TIPThe vehicle identification number is
used to identify your motorcycle and
may be used to register your motorcy-
cle with the licensing authority in yourarea.
EAU26441
Engine serial number
The engine serial number is stamped
into the crankcase.
1. Vehicle identification number
1
1. Engine serial number
1
2RD-9-E0.book 1 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

10-1
1
2
3
4
5
6
7
8
91011
12
INDEX
AAir filter element, replacing ...................... 6-12
Auxiliary light bulb, replacing ................... 6-34BBattery ..................................................... 6-28
Brake and clutch levers, checking and lubricating .............................................. 6-25
Brake fluid, changing ............................... 6-21
Brake fluid level, checking ....................... 6-20
Brake lever ................................................ 3-6
Brake lever free play, adjusting ............... 6-17
Brake light switches ................................. 6-19
Brake pads and shoes, checking............. 6-20
Brake pedal ............................................... 3-6
Brake pedal, checking and lubricating ..... 6-25
Brake pedal height and free play, adjusting ................................................ 6-18CCables, checking and lubricating ............. 6-24
Care ........................................................... 7-1
Catalytic converter ..................................... 3-9
Centerstand and sidestand, checking and lubricating ....................................... 6-26
Clutch lever................................................ 3-5
Clutch lever free play, adjusting .............. 6-16DDecompression lever ............................... 3-11
Dimmer switch ........................................... 3-4
Drive chain, cleaning and lubricating ....... 6-23
Drive chain slack ..................................... 6-22EEngine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-13
Engine oil and oil filter element.................. 6-9 Engine serial number ................................ 9-1
Engine stop switch .................................... 3-5
Engine trouble warning light ...................... 3-3
FFront fork, checking................................. 6-27
Fuel ........................................................... 3-7
Fuel cock ................................................. 3-10
Fuel consumption, tips for reducing .......... 5-3
Fuel level warning light .............................. 3-3
Fuel tank breather/overflow hose .............. 3-9
Fuel tank cap............................................. 3-7
Fuses, replacing ...................................... 6-29HHandlebar switches ................................... 3-4
Hazard switch............................................ 3-5
Headlight bulb, replacing......................... 6-31
High beam indicator light ........................... 3-3
Horn switch ............................................... 3-5IIdentification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-13
Indicator lights and warning lights ............. 3-2KKickstarter ............................................... 3-10MMain switch/steering lock .......................... 3-1
Maintenance and lubricatio
n, periodic....... 6-4
Maintenance, emission control system ..... 6-3
Matte color, caution ................................... 7-1
Model label ................................................ 9-2NNeutral indicator light ................................ 3-2PPanel, removing and installing .................. 6-7 Parking.......................................................5-4
Part locations .............................................2-1
Pass switch ................................................3-4
SSafety information ......................................1-1
Seat ......................................................... 3-11
Shifting .......................................................5-2
Shift pedal ..................................................3-6
Shift pedal, checking................................ 6-19
Shock absorber assemblies, adjusting ....3-12
Sidestand .................................................3-12
Spark plug, checking .................................6-8
Specifications.............................................8-1
Speedometer unit ......................................3-3
Starting the engine.....................................5-1
Starting the engine, trouble........................5-2
Steering, checking ................................... 6-27
Storage ......................................................7-3
Swingarm pivots, lubricating .................... 6-26TTachometer................................................3-4
Tail/brake light bulb, replacing ................. 6-32
Throttle grip and cable, checking and
lubricating ..............................................6-24
Throttle grip free play, checking............... 6-13
Tires ......................................................... 6-14
Tool kit .......................................................6-2
Troubleshooting ....................................... 6-39
Troubleshooting chart ..............................6-40
Turn signal indicator light ...........................3-2
Turn signal light bul b, replacing ............... 6-33
Turn signal switch ......................................3-4VValve clearance ....................................... 6-13
2RD-9-E0.book 1 ページ ２０１３年１１月２８日　木曜日　午後４時１８分