2014 SKODA ROOMSTER tyre pressure

Loosening/tightening wheel boltsFig. 148
Changing a wheel: Loosening the
wheel bolts
Read and observe on page 166 first.
Before removing the wheel bolts, the caps for the wheel bolts must be pulled
off.
Releasing
›
Push the wheel wrench onto the wheel bolt as far as the stop 1)
.
›
Grip the wrench at its end and turn the bolt about one turn in the direction of
the arrow » Fig. 148.
Tightening
›
Push the wheel wrench onto the wheel bolt as far as the stop 1)
.
›
Grip the wrench at its end and turn the bolt against the direction of the ar-
row » Fig. 148 until it is tight.
After tightening the wheel bolts, the covering caps must be replaced.
WARNING■ Undo the wheel bolts only a little (about one turn) provided that the vehi-
cle has not yet been jacked up. Otherwise the wheel could become loose
and fall off.■
If it proves difficult to undo the bolts, carefully apply pressure to the end
of the wrench with your foodt. Keep hold of the vehicle when doing so, and
make sure you keep your footing.
Raising the vehicleFig. 149
Jacking points for positioning
lifting jack
Fig. 150
Attach lifting jack
Read and observe
on page 166 first.
In order to raise the vehicle, the jack from the tool kit is to be used.
Position the car jack below the jacking point closest to the flat tyre » Fig. 149.
The mounting points are located on the metal bar of the lower sill on the un-
derside of your vehicle. The positions of these are embossed by means of
markings on the side surface of the lower sill » Fig. 150.
›
Support the base plate of the jack with its full area resting on level ground
and ensure that the jack is located in a vertical position at the jacking
point » Fig. 150 -
 .
›
Position the lifting jack below the jacking point with the crank and move it up
until its claw encloses the web » Fig. 150 -
 . 
1)
Use the appropriate adapter for undoing and tightening the anti-theft wheel bolts
» page 169.
168Do-it-yourself

›There is damage to the tyre wall.
› Driving with very low tyre pressure or with a completely flat tyre.
› If the use-by-date (see inflation bottle) has passed.WARNING■
If you are in flowing traffic, switch on the hazard warning light system
and set up the warning triangle at the prescribed distance! The national le-
gal requirements must be observed.■
Park the vehicle as far away as possible from the flow of traffic. Park on
as flat and firm a surface as possible.
WARNING■ A tyre filled with sealant has the same driving characteristics as a stand-
ard tyre.■
Do not drive faster than 80 km/h (50 mph).
■
Avoid accelerating at full throttle, sharp braking and fast cornering.
■
The sealant is hazardous to heath. Remove immediately if it comes into
contact with the skin.
■
Observe the manufacturer's usage instructions for the breakdown kit.
For the sake of the environment
Used sealant or sealant whose expiry date has passed must be disposed of in
accordance with environmental protection regulations.
Note
■ A new bottle of sealant can be purchased from ŠKODA Original Parts.■Immediately replace the tyre that was repaired using the breakdown kit, or
consult a specialist garage about repair options.Components of the puncture repair kitsFig. 152
Principle sketch: Components of the breakdown kit
Read and observe
on page 170 first.
Components of the set » Fig. 152
Valve remover
Sticker with “max. 80 km/h”/“max. 50 mph” speed designation
Inflation hose with plug
Air compressor
Tyre inflation hose
Tyre inflation pressure indicator
Air release valve
ON and OFF switch
12 volt cable connector
Tyre inflator bottle with sealing agent
Replacement valve core
The valve remover
1
has a slot at its lower end which fits into the valve core.
The kit is located in a box under the floor covering in the luggage compart-
ment. This contains a sealing means and an air compressor.
Note
The declaration of conformity is included with the air compressor or the log
folder.1234567891011170Do-it-yourself

Preparations for using the breakdown kitRead and observe
on page 170 first.
The following preparatory work must be carried out before using the puncture
repair kit.
›
Have all the occupants get out. The passengers should not stand on the
road (instead they should remain behind a crash barrier, for instance) while
the wheel is being changed.
›
Switch off the engine.
›
Engage the 1st gear or place the selector lever of the automatic transmission
in the P-position .
›
Apply the handbrake firmly.
›
Check that you can carry out the repairs with the breakdown kit » page 169.
›
Uncouple a trailer.
›
Remove the
breakdown kit from the boot.
›
Stick the appropriate sticker
2
» Fig. 152 on page 170 onto the dashboard in
the driver's field of view.
›
Unscrew the valve cap.
›
Use the valve remover
1
to unscrew the valve core and place it on a clean
surface (rag, paper, etc.).
Sealing and inflating the tyre
Read and observe
on page 170 first.
Sealing
›
Shake the tyre inflator bottle
10
» Fig. 152 on page 170 vigorously several
times.
›
Firmly screw the inflation hose
3
onto the tyre inflator bottle
10
in a clock-
wise direction. The film on the cap is pierced automatically.
›
Remove the plug from the inflation hose
3
and plug the open end fully onto
the tyre valve.
›
Hold the bottle
10
with the bottom facing upwards and fill all of the sealing
agent from the tyre inflator bottle into the tyre.
›
Remove the empty tyre inflator bottle from the valve.
›
Screw the valve core back into the tyre valve using the valve remover
1
.
Inflating
›
Screw the air compressor tyre inflation hose
5
» Fig. 152 on page 170 firmly
onto the tyre valve.
›
Check that the air release valve
7
is closed.
› Start the engine and run it in idle.›Plug the connector 9 into 12 Volt socket
» page 82, 12-volt power outlet .›
Switch on the air compressor with the ON and OFF switch
8
.
›
Allow the air compressor to run until a pressure of 2.0 - 2.5 bar is achieved.
Maximum run time of 8 minutes » .
›
Switch off the air compressor.
›
If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation
hose
5
from the tyre valve.
›
Drive the vehicle 10 metres forwards or backwards to allow the sealing agent
to “distribute” in the tyre.
›
Firmly screw the tyre inflation hose
5
back onto the tyre valve and repeat
the inflation process.
›
If you cannot reach the required tyre inflation pressure here either, this
means the tyre has sustained too much damage. You cannot seal with tyre with the breakdown kit »
.
›
Switch off the air compressor.
›
Remove the tyre inflation hose
5
from the tyre valve.
Once a tyre pressure of 2.0 – 2.5 bar is reached, the journey may be continued
at a maximum speed of 80 km/h (50 mph).
WARNING■ If you cannot inflate the tyre to at least 2.0 bar, this means the damage
sustained was too serious. The sealing agent cannot be used to seal the
tyre. 
Do not drive the vehicle any further! Seek help from a specialist ga-
rage.■
The tyre inflation hose and air compressor may get hot as the tyre is be-
ing inflated – there is a risk of burning.
CAUTION
Switch off the air compressor after running 8 minutes at the latest – there is a
risk of overheating. Allow the air compressor to cool a few minutes before
switching it on again.
Notes for driving with tyre repaired
Read and observe
on page 170 first.
The inflation pressure of the repaired tyre must be checked after driving for 10
minutes. 
171Emergency equipment and self-help

If the tyre pressure is 1.3 bar or less› Do not drive the vehicle! You cannot properly seal with tyre with the
breakdown kit.
If the tyre pressure is 1.3 bar or more›
Set the tyre pressure back to the correct value.
›
Continue driving carefully to the nearest specialist garage at a maximum speed of 80 km/h (50 mph).
Jump-starting
 Introduction
This chapter contains information on the following subjects:
Jump-starting using the battery from another vehicle
172
Jump-starting in vehicles with the START-STOP system
173
The battery of another vehicle can be used to jump-start your vehicle if the en-
gine will not start because the battery is flat.
WARNING■ Pay attention to the warning instructions relating to work in the engine
compartment » page 145.■
A discharged vehicle battery may already freeze at temperatures just be-
low 0 °C. If the battery is frozen, do not jump start with the battery of an-
other vehicle – there is a risk of explosion.
■
Keep any sources of ignition (naked flame, smouldering cigarettes, etc.)
away from the battery – risk of explosion!
■
Never jump-start vehicle batteries with insufficient acid levels – risk of
explosion and chemical burns.
■
The vent screws of the battery cells must be tightened firmly.
Note
We recommend you buy jump-start cables from a car battery specialist.Jump-starting using the battery from another vehicleFig. 153
Jump-starting: A – flat battery, B
– battery providing current
Read and observe on page 172 first.
The starting process using the battery of another vehicle requires the use of
jumper cables.
The jump-start cables must be attached in the following sequence.
›
Attach clamp
1
to the positive terminal of the discharged battery
A
» Fig. 153 .
›
Attach clamp
2
to the positive terminal of the battery supplying power
B
.
›
Attach clamp
3
to the negative terminal of the battery supplying power
B
.
›
Attach clamp
4
to a solid metal component firmly connected to the engine
block or to the engine block itself.
Starting engine
›
Start the engine on the vehicle providing the power and allow it to idle.
›
Start the engine of the vehicle with the discharged battery.
›
If the engine does not start, halt the attempt to start the engine after 10 sec-
onds and wait for 30 seconds before repeating the process.
›
Remove the jumper cables exactly in the reverse sequence as for clamping.
Both batteries must have a rated voltage of 12 V. The capacity (Ah) of the bat-
tery supplying the power must not be significantly less than the capacity of
the discharged battery in your vehicle.
Jump-start cables
Only use jump-start cables which have an adequately large cross-section and
insulated terminal clamps. Obey the instructions of the jump start cable manu-
facturer.
Positive cable - colour coding in the majority of cases is red.
Negative cable - colour coding in the majority of cases is black. 
172Do-it-yourself

DoorChild safety lock48
Closing48
Indicator light for an open door40
Opening48
Doors Emergency locking
49
Driving Abroad
118
Driving through water on streets117
Emissions184
Fuel consumption184
Maximum speed186
Driving economically Economical gear changing
114
Driving through water117
E
Economical and environmentally friendly driv- ing
113
Economical driving Ballast
115
Driving at full throttle115
Idling115
Looking ahead114
Regular maintenance116
Saving energy116
Short distances115
Tyre pressure115
EDL120
Electrical power windows Button in the driver's door
55, 56
Button in the rear door56
Central locking system57
Operational faults57
Electronic Differential Lock120
Electronic immobilizer107
emergency opening the loading door (Praktik)
89
EmergencyChanging a wheel166
Hazard warning light system63
jump-starting172
Jump-starting172
locking of the doors49
Selector lever-unlocking112
Towing the vehicle173
Towing the vehicle using the tow hitch174
tyre repair169
Unlocking the boot lid55
Emergency equipment Fire extinguisher
165
First aid kit165
Jack166
Vehicle tool kit166
Warning triangle165
Emissions184
Engine Running in
113
Starting and stopping the engine106
Switching off the engine107
Engine compartment145
Brake fluid152
Coolant151
Overview147
Vehicle battery153
Engine number183
Engine oil148
Capacity148
Checking149
Replenishing150
Specifications148
Warning light40
Engine revolutions counter31
Environment113
Environmental compatibility116
Environmentally friendly driving113
ESC Function119
Warning light42
F
Films
137
Fire extinguisher165
First aid kit165
Flashers61
Fog lights61
Folding down the seats
70
Footmats109
see Footmats109
Front airbag18
Front seats69
Fuel142
Diesel144
Fuel gauge31
gauge31
refer to Fuel142
Refuelling143
Unleaded petrol143
Fuel consumption113, 184
Fuses Assignment
175
Colour coding175
Replacing175
G
Gear Recommended gear
32
Gearbox Display messages
38
Gear changing Gear stick
109
General view Cockpit
29
Genuine parts133
192Index

Glow plug systemWarning light43
GSM97
H
Handbrake
109
Hazard warning light system63
Head airbag19
Headlight cleaning system Headlight cleaning system
67
Headlights179
Driving abroad118
Headlight cleaning system67
Headrest Headrest
73
Head restraint72
Heating Deicing the windows
92
Exterior mirrors68
Operating91
Operation91
Rear window64
Recirculated air mode92
Seats69
Heating and air-conditioning90
Hill hold control119
Hitch126
Accessories129
Drawback load126
Horn29
I
Ignition
107
Ignition lock107
Immobilizer107
Individual settings locking
50
unlocking50
Inertia reels15
Instrument cluster30
Overview30
see instrument cluster30
Interior monitor54
Internal lighting Praktik
89
Internal lights Praktik
89
ISOFIX25
J
Jack
166
Maintenance138
Jump-starting172
L
lashings Praktik
88
Light Cockpit
63
Dimmed headlights59
Headlight beam adjustment60
Headlight flash61
Sidelights59
Lights59
Cockpit63, 64
Daylight running60
Fog lights61
Foglights with the CORNER function62
Halogen projector headlights with cornering light function
61
Hazard warning light system63
Main beam lights61
Parking lights63
Rear fog light62
Replacing bulbs178
Tourist lights62
Turn signals61
warning lights39
Lock Central locking system51
Locking Emergency locking
49
Remote control52
without central locking49
Locking and unlocking from the inside51
Low tyre pressure warning refer to the tyre pressure monitoring
125
Luggage compartment Class N1 vehicles
74
Lighting64
Variable loading floor76
Luggage compartment lid54
M
Main beam
61
Maintenance116
Decorative films137
Manual air conditioning Recirculated air mode
94
Manual gear changing see gear changing
109
MAXI DOT Main menu
37
see MAXI DOT display37
Settings38
MAXI DOT display37
Maximum permissible weights
183
Maximum speed186
MDI104
Mechanical windows58
open and close58
Media see radio / navigation system
4
193Index

MirrorExterior mirrors68
Manually dimmed rear-view mirror68
Vanity65
Mobile phone97
Connecting to the hands-free system100
Modes of the automatic transmission110
Modifications132
Modifications and technical alterations Airbags
134
Service133
Spoiler134
Multifunction display Functions
33
Memory33
Operation34
Multimedia103
N
N1
74
Nameplate183
Navigation system4
Net partition76
Notes for driving with tyre repaired171
O
Oil See Engine oil
149
Oil pressure Display messages
40
Onboard computer see Multifunction display
33
Operating weight184
Operation in winter Diesel fuel
144
Vehicle battery154
Original accessories133
Outside temperature34
Overview Engine compartment147
warning lights39
P
Paintwork See Paintwork care
137
Paintwork care137
Panoramic roof65
Parking Parking aid
120
Part replacement132
Passive safety Before setting off
8
Driving safety8
Safety equipment8
Passive Safety8
Payload184
Pedals109
Footmats109
Petrol refer to Fuel
143
Polishing the paintwork See Taking care of your vehicle
137
Power window force limiter57
praktik adjusting the safety partition
88
Praktik87
Adjustable safety partition behind the front seats
88
emergency release of the loading area door89
Fastening the loading floor88
Internal lighting89
Internal lights89
Puncture set169
R
Radiator fan
147
Radio4
Radio reception See windows138
Raising the vehicle168
Rear-view mirror Exterior mirrors
68
Manually dimmed rear-view mirror68
Rear fog light62
rear seats in the longitudinal direction
70
Tilt the seat backrest70
Rear seats70
Rear Seats fold back into the starting position
72
Rear window heating64
Recirculated air mode Manual air conditioning
94
Recommended gear32
Refuelling143
Fuel143
Regulation Headlight beam
60
Remote control52
Synchronisation process53
Remote control key Replacing the battery
47
Repairs and technical alterations132
Replacing Bulb for the licence plate light
181
Fuses175
Fuses in the dash panel176
Fuses in the engine compartment177
Vehicle battery155
Windscreen wiper blades67
Replenishing Coolant
151
Engine oil150
Windscreen washer fluid147
Running-in The first 1500 km
113
194Index

Running inBrake pads113
Engine113
Tyres113
S
SAFE see Safe securing
50
SAFELOCK see Safe securing
50
Safe securing50
Safety8
Child safety22
Child safety seats22
Correct seated position9
Head restraints72
ISOFIX25
TOP TETHER26
Safety belts rear middle seat
15
Saving electrical energy113
Seals Taking care of your vehicle
137
Seat Adjusting
69
Seat belt warning light
40
Seat belts12
Belt tensioners15
Cleaning141
fastening and unfastening14
Height adjustment15
Inertia reels15
The physical principle of a frontal collision13
Seats Head restraints
72
Heating69
Removing seats71
Seats and stowing69
Selector lever see Using the selector lever110
Service133
Service display36
Setting Heating
92
Manual air conditioning system94
Manually dimmed rear-view mirror68
Setting the clock Clock
32
Shifting gears Driving and saving energy
114
Side airbag19
Sidelights59
Snow chains164
Spare wheel159
Speedometer31
Speed symbol Refer to Wheels
161
Spoiler134
Stalk Main beam
61
Turn signals61
START-STOP123
Manually deactivating/activating the system124
Operating conditions for the system123
operation124
system-related automatic start-up124
Starting and stopping the engine106
Starting engine Jump-starting
172
Starting the engine107
Jump-starting172
Starting the engine107
START STOP Information messages
124
Jump-starting173
Steering wheel10
Storage83
Storage compartment Storage compartment on the driver's side84
Storage compartment on the front passenger side
84
Storage Compartment Lighting
64
Storage compartments83
Flexible storage compartment87
Storage compartment in the front centre con- sole
85
storage pockets on the front seat84
Stowage compartment beneath the front seat
85
compartment for glasses85
compartments in the doors86
compartments in the luggage87
sun roof65
sunshade65
Sun visors65
Switching off the engine107
Synthetic leather141
T
Taking care of the vehicle Natural leather
140
Seat belts141
Taking care of your vehicle Automatic car wash system
135
Cavity protection138
Chrome parts137
Cleaning the wheels139
Decorative films137
Door lock cylinders138
Headlight lenses138
High-pressure cleaner136
Plastic parts137
Polishing the paintwork137
Rubber seals137
Taking care of the interior139
Taking care of your vehicle exterior136
195Index