2014 SKODA FABIA wheel

Downloaded from www.Manualslib.com manuals search engine Bulb arrangement in the headlightsFig. 194
Principle sketch: Halogen headlights/halogen projector head-
lights
Read and observe
and on page 184 first.
The vehicle is equipped with headlights with halogen bulbs.
Bulb arrangement » Fig. 194
Dayl. dri. light
Low beam, high beam and parking light
Flashing
Low beam
High beam and turning signal switch
Removing and installing the cover in the front wheel arch
Fig. 195
Remove the plastic cover
Read and observe and on page 184 first.
The cover in the front wheel must be removed in order to change certain light
bulbs.
ABCDEDetails about removing the cover - if needed - are given in the description of
each lamp change.
Removing›
Adjust front wheels in the direction of centre of the vehicle.
›
Insert the clamp for removing the full wheel covers » page 167, Vehicle tool
kit into the recess in the cover.
›
Remove the cover by pulling the hook in the direction of arrow » Fig. 195.
Fitting
›
Insert and push the cover into the corresponding opening.
The cover must engage securely.
Fitting and removing the wash water container nozzle
Fig. 196
Remove the holder of the wash water container nozzle
Read and observe
and on page 184 first.
The holder of the wash water container nozzle must be removed in order to
replace some light bulbs. The holder is located in the engine compartment,
front right. 
185Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine Details about removing the holder - if needed - are given in each lamp replace-
ment description .
Removing›
Unclip the container nozzle
A
from the holder in the direction of arrow
1
» Fig. 196 .
›
Insert a finger into the recess
B
in the direction of arrow
2
and lift the catch
C
in the direction of arrow
3
.
›
Remove the holder of the container nozzle in the direction of arrow
4
.
Fitting
›
Slide the holder of the container nozzle in the opposite direction to the ar-
row
4
» Fig. 196 .
The holder must engage firmly.
›
Push the container nozzle into the holder in the opposite direction to the ar-
row
1
.
Replacing the low beam and high beam bulb (halogen headlights)
Fig. 197
Replacing the bulb for low beam and main beam
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
To replace lamp, first remove the bracket of the wash water container nozzle
in the right headlight » page 185.
›
Remove the protective cap
B
» Fig. 194 on page 185 .
›
Press the connector latch and remove the plug connector by jiggling in the
direction of arrow
1
» Fig. 197 .
›
Push in the spring in the direction of the arrow
2›
Release the spring in the direction of the arrow
3
.
›Remove the defective bulb in the direction of arrow 4.›Fit a new bulb into the headlamp and secure the spring in the opposite direc-
tion to the arrow 3
.
›
Insert the plug in the opposite direction to the arrow
1
.
›
Fit protective cap
B
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
›
Replace the appropriate cover in the front wheel arch » page 185.
Change bulb for turn signal switch (halogen headlight)
Fig. 198
Changing the bulb for the front
turn signal light
Read and observe and on page 184 first.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
C
» Fig. 194 on page 185 .
›
Turn the socket with the bulb in the direction of arrow
1
» Fig. 198 .
›
Remove the socket with the bulb in the direction of arrow
2
.
›
Insert the socket with the new bulb in the opposite direction to the arrow
2
.
›
Turn the socket with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Fit protective cap
C
» Fig. 194 on page 185 .
186Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Replacing the parking light bulb (halogen headlights)Fig. 199
Change the light bulb for the parking light
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
B
» Fig. 194 on page 185 .
›
Remove the bulb holder with the bulb by jiggling it out in the direction of the
arrow
1
» Fig. 199 .
›
Grasp the lamp socket at the places marked by arrows.
›
Remove the faulty bulb from the holder in the direction of the arrow
2
.
›
Push a new bulb into the bulb holder up to the stop.
›
Replace the bulb holder in the headlamp with the bulb.
›
Fit protective cap
B
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
›
Replace the appropriate cover in the front wheel arch » page 185.
Changing bulb for daytime running lights switch (halogen
headlight)Fig. 200
Changing the bulb for the day-
time running light
Read and observe and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
›
Turn the socket with the bulb in the direction of arrow
1
» Fig. 200 .
›
Remove the socket with the bulb in the direction of arrow
2
.
›
Change the bulb in the socket.
›
Insert the socket with the new bulb into the headlight in the opposite direc-
tion to the arrow
2
.
›
Turn the socket with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Replace the appropriate cover in the front wheel arch » page 185.
Replacing the dipped beam bulb (halogen projector headlights)
Fig. 201
Changing the bulb for the low beam
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185. 
187Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine ›Remove the protective cap D
» Fig. 194 on page 185 .›Turn the holder with the bulb in the direction of arrow 1 » Fig. 201 .›
Remove the holder with the bulb in the direction of arrow
2
.
›
Remove the bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the connector so that the lug
A
on the connector
snaps into the groove on the bulb.
›
Insert the connector with the new bulb into the headlight in the opposite di-
rection to the arrow
2
.
›
Turn the connector with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Fit protective cap
D
» Fig. 194 on page 185 .
›
Replace the appropriate cover in the front wheel arch » page 185.
Replacing the high beam bulb (halogen projector headlights)
Fig. 202
Changing the bulb for the main beam
Read and observe
and on page 184 first.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
E
» Fig. 194 on page 185 .
›
Turn the holder with the bulb in the direction of arrow
1
» Fig. 202 .
›
Remove the holder with the bulb in the direction of arrow
2
.
›
Remove the bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the connector so that the lug
A
on the connector
snaps into the groove on the bulb.
›
Insert the connector with the new bulb into the headlight in the opposite di-
rection to the arrow
2
.
›
Turn the connector with the new bulb in the opposite direction to the arrow
1
until it stops.
› Fit protective cap E
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
Replacing the turn signal switch bulb (halogen projector
headlights)
Fig. 203
Changing the bulb for the turn signal light
Read and observe
and on page 184 first.
To replace lamp, first remove the bracket of the wash water container nozzle
in the right headlight » page 185.
›
Remove the protective cap
E
» Fig. 194 on page 185 .
›
Remove the bulb holder with the bulb by jiggling it out in the direction of the
arrow
1
» Fig. 203 .
›
Grasp the lamp socket at the places marked by arrows.
›
Remove the faulty bulb from the holder in the direction of the arrow
2
.
›
Push a new bulb into the bulb holder up to the stop.
›
Replace the bulb holder in the headlamp with the bulb.
›
Fit protective cap
E
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
188Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Replacing the bulb for the fog lightFig. 204
Removing the fog lamp / changing bulb for fog light switch
Read and observe
and on page 184 first.
Remove the protective grille and headlight
›
Insert the clamps for removing the full wheel covers into opening
A
» page 167 , Vehicle tool kit .
›
Loosen the protective grille by pulling the hook in the direction of arrow
1
» Fig. 204.
›
Grasp the guard with the hand and remove by pulling in the direction of the
arrow
2
.
›
Unscrew the screws
B
with the screwdriver from the tool kit » page 167.
›
Remove the headlight in the direction of arrow
3
.
Replacing the light bulb
›
Push in the latch on the connector in the direction of arrow
4
» Fig. 204 .
›
Remove the key in the direction of the arrow
5
.
›
Turn the socket with the bulb to the stop in the direction of the arrow
6
.
›
Remove the socket with the bulb in the direction of arrow
7
.
›
Insert the new bulb into the headlight and turn counter to the direction of
arrow
6
as far as the stop.
› Attach the connector.
Refit the headlight and grille›
Replace the fog light by inserting it in the opposite direction of the arrow
3
» Fig. 204 and tightening.
›
Insert the protective grille and carefully press it in.
The protective grille must engage firmly.
Changing the licence plate light bulb
Fig. 205
Remove the licence plate light
Fig. 206
Remove the cover / replace the bulb
Read and observe
and on page 184 first.
›
Open the tailgate.
›
Push in the lamp in the direction of the arrow
1
» Fig. 205 .
The lamp comes loose.
›
Swivel out the lamp in the direction of the arrow
2
and remove it.
›
Remove the cap of the lamp in range
A
and in the direction of arrow
3
» Fig. 206 . 
189Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine ›Remove the cap of the light in the direction of arrow 4.›Remove the faulty bulb from the holder in the direction of the arrow 5.›
Insert a new bulb into the holder.
›
Clip in the cap of the lamp counter to the direction of arrow
4
.
›
Reinsert the lamp in the opposite direction to the arrow
1
.
›
Push on the light until the spring clicks into place.
Check that the light is securely inserted.
›
Shut the boot lid.
Rear Light
Fig. 207
Remove light / pull out connector
Read and observe
and on page 184 first.
Removing
›
Open the tailgate.
›
Unscrew the screws
A
with the screwdriver from the tool kit » page 167.
›
Into the opening
B
insert the clamps for removing the full wheel trims, di-
rected with the eyelet downward (in the right light with the eyelet upward).
›
Grasp the light with the palm of the hand and remove carefully in the direc-
tion of arrow
1
» Fig. 207 from the pin
D
.
›
Press the latch
C
on the holder in the direction of the arrow
2
.
›
Press the latch in the direction of arrow
3
and pull out the holder in the di-
rection of arrow
4
.
Fitting
›
Insert the bulb holder into the lamp.
›
Tighten the lock in the opposite direction to the arrow
2
» Fig. 207 .
›
Insert the lamp with the holes
B
» Fig. 208 on page 190 onto the pins
D
» Fig. 207 in the body.
›Carefully press the light into the pins on the bodywork
» .
Ensure that the wiring harness does not become pinched between the body
and the lamp.›
Screw the light into place.
CAUTION
■ Ensure that the wiring harness does not become pinched between the body
and the lamp when it is being refitted – risk of damage to the electrical instal-
lation and risk of water ingress.■
If you are not sure whether the wiring harness has become pinched, we rec-
ommend that you have the light connection checked by a specialist garage.
■
Ensure that the vehicle paintwork and the tail lamp are not damaged when
removing and installing the tail lamp.
Replacing bulbs in rear light
Fig. 208
Outer part of the lamp / removing the bulb / lamp holder
Read and observe
and on page 184 first.
Changing the bulb in the outer part of the lamp
›
Turn the holder with the bulb
A
in the direction of the arrow
1
» Fig. 208 .
›
Remove the socket with the bulb from the lamp housing in the direction of
arrow
2
.
›
Jiggle the bulb to remove.
›
Insert a new bulb into the socket.
›
Reinsert the holder with the bulb into the lamp housing and turn in the op-
posite direction of the arrow
1
to the stop.
Changing the bulb in the inner part of the lamp
›
Turn the holders with the bulbs
A
in the direction of the arrow
1
» Fig. 208 .
190Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Supplementary Information (applies to Russia)
The full type approval number of the means of transport is indicated in the
registration documents, field 17.WARNINGDo not exceed the specified maximum permissible weights – risk of an acci-
dent and damage.
Operating weight and payload
Operating weight
This value represents the minimum operating weight without additional
weight-increasing equipment such as air conditioning system, spare wheel, or
trailer hitch.
The specified operating weight is for orientation purposes only.
The operating weight also contains the weight of the driver (75 kg), the weight
of the operating fluids, the tool kit, and a fuel tank filled to 90 % capacity.
Operating weight of the vehicle » page 196, Vehicle-specific details per en-
gine type .
Payload
It is possible to calculate the approximate loading capacity from the difference
between the permissible total weight and the operating weight.
The payload consists of the following weights.
› The weight of the passengers.
› The weight of all items of luggage and other loads.
› The weight of the roof, including the roof rack system.
› The weight of the equipment that is excluded from the operating weight.
› Trailer drawbar load when towing a trailer (max. 50 kg).
Note
If required, you can find out the precise weight of your vehicle by contacting a
specialist garage.
measurement of fuel consumption and CO 2 emissions according to
ECE Regulations and EU Directives
The data on fuel consumption and CO 2 emissions were not available at the
time of going to press.
The data on fuel consumption and CO 2 emissions are given on the ŠKODA
websites or in the sales and technical vehicle documentation.
The measurement of the intra-urban cycle begins with a cold start of the en-
gine. Urban driving is then simulated.
In the extra-urban driving cycle, the vehicle is accelerated and decelerated in
all gears, corresponding to daily routine driving conditions. The driving speed
varies between 0 and 120 km/h.
The calculation of the combined fuel consumption considers a weighting of
about 37 % for the intra-urban cycle and 63 % for the extra-urban cycle.
Note
■ The fuel consumption and emission levels given on the Škoda websites or in
the commercial and technical vehicle documentation have been established in
accordance with rules and under conditions that are set out by legal or techni-
cal rules for the determination of operational and technical data of motor vehi-
cles.■
Depending on the extent of the equipment, the driving style, traffic condi-
tions, weather influences and vehicle condition, consumption values can in
practice result in fuel economy figures in the use of the vehicle that differ from
the fuel consumption values listed on the ŠKODA websites or in the commer-
cial and technical vehicle documentation.
193Technical data

Downloaded from www.Manualslib.com manuals search engine DimensionsFig. 210
Principle sketch: Vehicle dimensions
Vehicle dimensions by operating weight without driver (in mm)
» Fig. 210SpecificationFabiaFabia CombiA
Height
Basic dimension14671467Vehicles with off-road package14821482Vehicles with SPORT package14521452BFront trackBasic dimension14631463Vehicles with the 1.2 l/81 kW TSI and 1.4 l/77 kW TDI engine14571457CWidth17321732DRear trackBasic dimension14571457Vehicles with the 1.2 l/81 kW TSI and 1.4 l/77 kW TDI engine14511451EWidth including exterior mirrors19581958F
Clearance
Basic dimension133135Vehicles with off-road package141143Vehicles with SPORT package118120GWheelbase24702470HLength39924257194Technical data