2014 SKODA FABIA Operating Instruction Manual

Downloaded from www.Manualslib.com manuals search engine Assignment of the fuses in the dash panelFig. 191
Schematic representation of the fuse box for vehicles with left-
hand steering/right-hand steering
Read and observe
and on page 181 first.
No.Power consumer1Left parking light, parking light, high-mounted brake light2Central locking system3Relay for ignition4Right-hand light, rear fog light, license plate light5Power windows - driver6Central control unit, interior lighting7Horn8Towing hitch - left light
9
Operating lever beneath the steering wheel, engine control unit (on-
ly without KESSY), automatic gearbox (only without KESSY), selector
lever of the automatic gearbox (only without KESSY), ESC (only with-
out KESSY), control unit for trailer detection (only without KESSY),
power steering (only without KESSY), airbag (only without KESSY)10Power windows - rear left11Headlight cleaning system12Radio display1312 volt socket in luggage compartment14Operating lever under the steering wheel, light switch, ignition key
removal lock (automatic gearbox), diagnostic connector, headlight
flasher, SmartGate controller, rain sensor, light sensorNo.Power consumer15Control unit for air conditioning system, selector lever of the auto-
matic gearbox16Instrument cluster17Alarm system, horn18Not assigned19Not assigned20Not assigned21Not assigned22Front- and rear windscreen wiper system23Not assigned24Blower fan for air conditioning system, heating, control unit for air
conditioning, heating25Not assigned26Switch for front seat heating27Rear window wiper28Not assigned29Airbag (only with KESSY)
30
Power windows, light switches, reverse light switches, control unit
for air conditioning system, control unit for park assist, exterior mir-
ror, power feed for centre button strip, power feed for side button
strip, interior mirror31Fuel pump, control unit for radiator fan, cruise control, coil of the re-
lay for the front and rear windscreen wipers32Diagnostic connector, headlight range adjustment33Coil on starter relay, clutch pedal switch34Heated windscreen washer jets35Not assigned36Heated front seats37Radar38Not assigned39Electrical auxiliary heating system40Not assigned41Rear window heater 182Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine No.Power consumer42Power windows - front passenger43Towing hitch - contact in the socket44Cigarette lighter, 12-volt power socket45Power windows - rear right46Front and rear window washer, operating lever under the steering
wheel47Towing hitch - contact in the socket48Towing hitch - right light49Control unit for fuel pump50Radio51Heating of the external mirror52KESSY control unit53KESSY steering lock54Not assigned55Heated front seats56Not assigned57Not assigned58Not assigned59Not assigned
Fuses in the engine compartment
Fig. 192
Remove the cover
Read and observe and on page 181 first.
Replacing fuses
›
Press the lock button on the cover in direction of arrow
1
» Fig. 192 .
›
Raise the cover and remove in the direction of the arrow
2
.
›
Remove the plastic clip from the holder on the cover of the fuse box in the
dash panel.
›
Replace the appropriate fuse.
›
Replace the clamp in the original position.
›
Place the cover on top of the fuse box.
›
Push in the locking button on the cover and lock.
The cover must engage securely.
Fuse assignment in the engine compartment
Fig. 193
Fuses
Read and observe and on page 181 first.
No.Power consumer1Radiator fan2Control unit for glow plug system3Control unit for ABS/ESC4Electrical auxiliary heating system5Electrical auxiliary heating system6Automatic gearbox7Engine control unit8Windscreen wipers9Central control unit, battery data module10Control unit for ABS/ESC 183Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine No.Power consumer11Not assigned12Engine components13Brake pedal switch14Engine components, coil of the fuel pump relay15Engine control unit16Starter17Engine control unit18Engine components, coils of the relay for auxiliary electric heater, radi-
ator fan19Lambda probe20Engine components, control unit for glow plug system, heating the
crankcase ventilation
Replacing bulbs
 Introduction
This chapter contains information on the following subjects:
Bulb arrangement in the headlights
185
Removing and installing the cover in the front wheel arch
185
Fitting and removing the wash water container nozzle
185
Replacing the low beam and high beam bulb (halogen headlights)
186
Change bulb for turn signal switch (halogen headlight)
186
Replacing the parking light bulb (halogen headlights)
187
Changing bulb for daytime running lights switch (halogen headlight)
187
Replacing the dipped beam bulb (halogen projector headlights)
187
Replacing the high beam bulb (halogen projector headlights)
188
Replacing the turn signal switch bulb (halogen projector headlights)
188
Replacing the bulb for the fog light
189
Changing the licence plate light bulb
189
Rear Light
190
Replacing bulbs in rear light
190
Some manual skills are required to change a bulb. For this reason, if uncertain,
we recommend that bulbs are replaced by a specialist garage or other expert
help is sought.
› Switch off the ignition and all of the lights before replacing a bulb.
› Faulty bulbs must only be replaced with the same type of bulbs. The designa-
tion is located on the light socket or the glass bulb.
› A stowage compartment for replacement bulbs is located in a plastic box in
the spare wheel or underneath the floor covering in the boot.WARNING■ Always read and observe the warnings before completing any work in the
engine compartment » page 149.■
Accidents can be caused if the road in front of the vehicle is not suffi-
ciently illuminated and the vehicle cannot or can only be seen with difficul-
ty by other road users.
■
Bulbs H8, H7 and H4 are pressurised and may burst when changed - there
is a risk of injury! We therefore recommended wearing gloves and safety
glasses when changing a bulb.
■
Switch off the respective vehicle light when changing the bulb.
CAUTION
Do not take hold of the glass bulb with naked fingers (even the smallest
amount of dirt reduces the working life of the light bulb). Use a clean cloth,
napkin, or similar.
Note
■ This Owner's Manual only describes the replacement of bulbs where it is pos-
sible to replace the bulbs on your own without any complications arising. Other
light bulbs should be changed by your specialist garage.■
We recommend that you always carry a box of replacement bulbs in the vehi-
cle. Replacement bulbs can be purchased from ŠKODAOriginal Accessories.
■
We recommend having the headlight settings checked by a specialist garage
after replacing a bulb in the main beam, low beam or fog lights.
■
Visit a specialist garage if an LED is faulty.
184Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Bulb arrangement in the headlightsFig. 194
Principle sketch: Halogen headlights/halogen projector head-
lights
Read and observe
and on page 184 first.
The vehicle is equipped with headlights with halogen bulbs.
Bulb arrangement » Fig. 194
Dayl. dri. light
Low beam, high beam and parking light
Flashing
Low beam
High beam and turning signal switch
Removing and installing the cover in the front wheel arch
Fig. 195
Remove the plastic cover
Read and observe and on page 184 first.
The cover in the front wheel must be removed in order to change certain light
bulbs.
ABCDEDetails about removing the cover - if needed - are given in the description of
each lamp change.
Removing›
Adjust front wheels in the direction of centre of the vehicle.
›
Insert the clamp for removing the full wheel covers » page 167, Vehicle tool
kit into the recess in the cover.
›
Remove the cover by pulling the hook in the direction of arrow » Fig. 195.
Fitting
›
Insert and push the cover into the corresponding opening.
The cover must engage securely.
Fitting and removing the wash water container nozzle
Fig. 196
Remove the holder of the wash water container nozzle
Read and observe
and on page 184 first.
The holder of the wash water container nozzle must be removed in order to
replace some light bulbs. The holder is located in the engine compartment,
front right. 
185Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine Details about removing the holder - if needed - are given in each lamp replace-
ment description .
Removing›
Unclip the container nozzle
A
from the holder in the direction of arrow
1
» Fig. 196 .
›
Insert a finger into the recess
B
in the direction of arrow
2
and lift the catch
C
in the direction of arrow
3
.
›
Remove the holder of the container nozzle in the direction of arrow
4
.
Fitting
›
Slide the holder of the container nozzle in the opposite direction to the ar-
row
4
» Fig. 196 .
The holder must engage firmly.
›
Push the container nozzle into the holder in the opposite direction to the ar-
row
1
.
Replacing the low beam and high beam bulb (halogen headlights)
Fig. 197
Replacing the bulb for low beam and main beam
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
To replace lamp, first remove the bracket of the wash water container nozzle
in the right headlight » page 185.
›
Remove the protective cap
B
» Fig. 194 on page 185 .
›
Press the connector latch and remove the plug connector by jiggling in the
direction of arrow
1
» Fig. 197 .
›
Push in the spring in the direction of the arrow
2›
Release the spring in the direction of the arrow
3
.
›Remove the defective bulb in the direction of arrow 4.›Fit a new bulb into the headlamp and secure the spring in the opposite direc-
tion to the arrow 3
.
›
Insert the plug in the opposite direction to the arrow
1
.
›
Fit protective cap
B
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
›
Replace the appropriate cover in the front wheel arch » page 185.
Change bulb for turn signal switch (halogen headlight)
Fig. 198
Changing the bulb for the front
turn signal light
Read and observe and on page 184 first.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
C
» Fig. 194 on page 185 .
›
Turn the socket with the bulb in the direction of arrow
1
» Fig. 198 .
›
Remove the socket with the bulb in the direction of arrow
2
.
›
Insert the socket with the new bulb in the opposite direction to the arrow
2
.
›
Turn the socket with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Fit protective cap
C
» Fig. 194 on page 185 .
186Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Replacing the parking light bulb (halogen headlights)Fig. 199
Change the light bulb for the parking light
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
B
» Fig. 194 on page 185 .
›
Remove the bulb holder with the bulb by jiggling it out in the direction of the
arrow
1
» Fig. 199 .
›
Grasp the lamp socket at the places marked by arrows.
›
Remove the faulty bulb from the holder in the direction of the arrow
2
.
›
Push a new bulb into the bulb holder up to the stop.
›
Replace the bulb holder in the headlamp with the bulb.
›
Fit protective cap
B
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
›
Replace the appropriate cover in the front wheel arch » page 185.
Changing bulb for daytime running lights switch (halogen
headlight)Fig. 200
Changing the bulb for the day-
time running light
Read and observe and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
›
Turn the socket with the bulb in the direction of arrow
1
» Fig. 200 .
›
Remove the socket with the bulb in the direction of arrow
2
.
›
Change the bulb in the socket.
›
Insert the socket with the new bulb into the headlight in the opposite direc-
tion to the arrow
2
.
›
Turn the socket with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Replace the appropriate cover in the front wheel arch » page 185.
Replacing the dipped beam bulb (halogen projector headlights)
Fig. 201
Changing the bulb for the low beam
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185. 
187Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine ›Remove the protective cap D
» Fig. 194 on page 185 .›Turn the holder with the bulb in the direction of arrow 1 » Fig. 201 .›
Remove the holder with the bulb in the direction of arrow
2
.
›
Remove the bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the connector so that the lug
A
on the connector
snaps into the groove on the bulb.
›
Insert the connector with the new bulb into the headlight in the opposite di-
rection to the arrow
2
.
›
Turn the connector with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Fit protective cap
D
» Fig. 194 on page 185 .
›
Replace the appropriate cover in the front wheel arch » page 185.
Replacing the high beam bulb (halogen projector headlights)
Fig. 202
Changing the bulb for the main beam
Read and observe
and on page 184 first.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
E
» Fig. 194 on page 185 .
›
Turn the holder with the bulb in the direction of arrow
1
» Fig. 202 .
›
Remove the holder with the bulb in the direction of arrow
2
.
›
Remove the bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the connector so that the lug
A
on the connector
snaps into the groove on the bulb.
›
Insert the connector with the new bulb into the headlight in the opposite di-
rection to the arrow
2
.
›
Turn the connector with the new bulb in the opposite direction to the arrow
1
until it stops.
› Fit protective cap E
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
Replacing the turn signal switch bulb (halogen projector
headlights)
Fig. 203
Changing the bulb for the turn signal light
Read and observe
and on page 184 first.
To replace lamp, first remove the bracket of the wash water container nozzle
in the right headlight » page 185.
›
Remove the protective cap
E
» Fig. 194 on page 185 .
›
Remove the bulb holder with the bulb by jiggling it out in the direction of the
arrow
1
» Fig. 203 .
›
Grasp the lamp socket at the places marked by arrows.
›
Remove the faulty bulb from the holder in the direction of the arrow
2
.
›
Push a new bulb into the bulb holder up to the stop.
›
Replace the bulb holder in the headlamp with the bulb.
›
Fit protective cap
E
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
188Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Replacing the bulb for the fog lightFig. 204
Removing the fog lamp / changing bulb for fog light switch
Read and observe
and on page 184 first.
Remove the protective grille and headlight
›
Insert the clamps for removing the full wheel covers into opening
A
» page 167 , Vehicle tool kit .
›
Loosen the protective grille by pulling the hook in the direction of arrow
1
» Fig. 204.
›
Grasp the guard with the hand and remove by pulling in the direction of the
arrow
2
.
›
Unscrew the screws
B
with the screwdriver from the tool kit » page 167.
›
Remove the headlight in the direction of arrow
3
.
Replacing the light bulb
›
Push in the latch on the connector in the direction of arrow
4
» Fig. 204 .
›
Remove the key in the direction of the arrow
5
.
›
Turn the socket with the bulb to the stop in the direction of the arrow
6
.
›
Remove the socket with the bulb in the direction of arrow
7
.
›
Insert the new bulb into the headlight and turn counter to the direction of
arrow
6
as far as the stop.
› Attach the connector.
Refit the headlight and grille›
Replace the fog light by inserting it in the opposite direction of the arrow
3
» Fig. 204 and tightening.
›
Insert the protective grille and carefully press it in.
The protective grille must engage firmly.
Changing the licence plate light bulb
Fig. 205
Remove the licence plate light
Fig. 206
Remove the cover / replace the bulb
Read and observe
and on page 184 first.
›
Open the tailgate.
›
Push in the lamp in the direction of the arrow
1
» Fig. 205 .
The lamp comes loose.
›
Swivel out the lamp in the direction of the arrow
2
and remove it.
›
Remove the cap of the lamp in range
A
and in the direction of arrow
3
» Fig. 206 . 
189Fuses and light bulbs