2014 Seat Toledo headlights

Operation
Switching off the wipers – Move the lever to position 0
››› Fig. 56 . WARNING
The rain sensor may not detect enough rain
to switch on the wipers.
● If necessary, switch on the wipers manually
when water on the windscreen obstructs visi-
bility. Note
Do not put stickers on the windscreen in front
of the rain sensor*. This may cause sensor
disruption or faults. Headlight washer system*
The headlight washers operate briefly if the
dipped headlights or headlights are on and
the lever is moved to position
5
›››
Fig. 56 .
The he a
dlight washer system also operates
every 10 windscreen wash cycles.
Clean off stubborn dirt (insects, etc.) from the
headlights at regular intervals, for instance
when filling the fuel tank. Please observe the
following indications ›››
page 126, Head-
lights.
To en

sure the system works properly in win-
ter, keep the nozzle holders free of snow and
remove any ice with a de-icer spray. CAUTION
Never pull on the nozzle holders. Risk of
damage to the system! Rear vision mirrors
Interior rear vision mirror with manual
anti-dazzle adjustment Basic settings
– Push the lever at the bottom of the mirror
forward.
Rear vision mirror anti-dazzle setting – Pull the lever at the bottom of the mirror to-
wards you.
Exterior mirrors Fig. 57
Door interior: adjuster knob. Before beginning any journey, adjust the rear
view mirrors for a good rear visibility.
Heated rear vision mirrors*
–
Turn the knob to position 
›
›› Fig. 57
.
Electrical adjustment of the left-hand
exterior mirror*
– Turn the knob to position  ›
›› Fig. 57. The
mirror movements are the same as those of
the knob.
Electrical adjustment of the right-hand
exterior mirror*
– Turn the knob to position  ››› Fig. 57. The
mirror mo

vements are the same as those of
the knob. WARNING
● Convex (wide-angle) rear vision mirrors give
a larger field of vision. However, they make
objects appear smaller and further away than
they really are. For this reason, you should
not rely on these rear vision mirrors for judg-
ing the distance of vehicle behind.
● If possible, use the interior rear vision mir-
ror to estimate distances to vehicles behind
you. Note
● Exterior mirrors are only heated when the
engine is running. 70

Towing bracket device
altitude, this also reduces climbing ability,
which requires a reduction of the weight of
the vehicle with a trailer by 10% for every
1000 m increase in altitude. The weight of
the assembly is calculated by adding the ve-
hicle weight (loaded) to the trailer weight
(loaded). Always drive with special care when
towing a trailer.
The towed load and support load information
that is displayed on the towing bracket man-
ufacturers label are only values for the verifi-
cation of the device. The correct figures for
your specific vehicle, which are usually lower
than these figures, are given in the documen-
tation of your vehicle. WARNING
● Exceeding the maximum established load
per axle and the maximum towing bracket
load in addition to the maximum permitted
load or the load of the vehicle + trailer as-
sembly can cause accidents and serious inju-
ries.
● A sliding load can considerably affect the
stability and safety of the vehicle + trailer as-
sembly, resulting in accidents and serious in-
juries. Towing a trailer
Exterior mirrors
Check whether you can see enough of the
road behind the trailer with the standard rear
vision mirrors. If this is not the case, you
should have additional exterior mirrors fitted.
Observe the relevant statutory requirements
of the country you are in.
Headlights
Before starting a journey, also check the
headlight beam settings with the trailer
hitched up. Adjust the headlight range set-
tings if necessary
›››
page 62, Range control
of main lights .
Driving speed
For your own safety do not drive faster than
the maximum permitted speed indicated on
the trailer.
At all times, immediately reduce speed if you
detect the slightest swaying movement of the
trailer. Never try to “return the trailer to a
straight position” by accelerating.
Brakes
Brake in due course! If the trailer has an over-
run brake , apply the brakes gently at first and
then, firm ly
. This will prevent the jerking that
can be caused by locking of trailer wheels.
Change to a lower gear in good time before descending a slope in order to take advant-
age of the engine brake.
The trailer is incorporated into the vehicle's
anti-theft alarm system:
● When the vehicle has a factory-fitted anti-
theft alarm and a towing bracket.
● When the trailer is electrically connected to
the vehicle via the towing bracket socket.
● When the vehicle electrical device and the
towing bracket are operational.
● When the vehicle is locked and the vehi-
cle's anti-theft alarm device is activated.
Once the electrical connection is interrupted
with the vehicle trailer locked, the alarm
sounds.
Always switch off the vehicle anti-theft alarm
device before connecting or disconnecting a
trailer. The vehicle anti-theft alarm device
could cause the alarm to sound ››› page 57,
Anti-theft alarm system*.
Engine overheating
In the event that the coolant temperature
gauge needle moves to the right section of
the scale or to the red area, immediately re-
duce speed. If the control lamp  flashes on
the general instrument panel, stop the vehi-
cle and switch off the engine. Wait several
minutes and check the coolant level in the
tank ››› page 138
.
»
115
Technical specifications
Advice
Operation
Safety

Advice
●
Make sure you do not damage the paint-
work on the vehicle on removing snow and
ice from the windows and rear vision mirrors.
● Do not remove the snow or ice dirty with
thick particles, e.g. gravel, sand or road salt,
from windows and mirrors. Risk of damage to
the glass and mirror surfaces. Radio reception and aerial
In vehicles factory-fitted with an audio or
navigation system, the aerial may be instal-
led in different places:
● inside the rear window next to the heating
elements,
● on the roof of the vehicle.
Headlights Use soap and clean, hot water to clean the
front headlights.
CAUTION
● Never rub the headlights to dry them and
do not use sharp objects to clean the plastic
glass material. These could damage the pro-
tective paint and cause the headlights to
crack. ●
Do not use aggressive cleaning products or
chemical solvents to clean the glass. This
could damage the headlights. Care of rubber seals
The weatherstrips on doors and windows will
remain pliable and last longer if they are oc-
casionally treated with a suitable rubber care
product. This will prevent premature ageing
and leaks. If they are properly cared for, the
seals will be less likely to freeze up in the
winter.
Door lock cylinder Special products must be used to defrost
lock cylinders.
Note
● Make sure, when washing the vehicle, that
the least amount of water possible enters the
lock cylinders.
● We recommend the use of products from
the selection of SEAT Original Accessories to
care for the door lock cylinder. Wheels
Wheel trims
If you wash the vehicle regularly, you should
also thoroughly wash the wheel trim. Regu-
larly remove any brake dust and road salt
from the wheels, otherwise the wheel materi-
al could be damaged. Repair any damage to
the wheel paintwork immediately.
Alloy wheels
After thorough washing, treat the wheels
with a protective product for alloy wheels. Do
not use abrasive products to care for the
wheels.
WARNING
Moisture, ice and road salt may affect braking
efficiency. Risk of accident! CAUTION
Heavy dirt on the wheels could lead to their
misalignment. This could result in vibrations
being transmitted to the steering wheel that
under certain conditions may cause prema-
ture steering wear. This dirt must be re-
moved. Note
We recommend you leave paint damage re-
pairs to a SEAT Authorised Service. 126

Advice
The capacity
of the reservoir is approximately
3.5 litr
es; in vehicles with a headlight washer
system, it is approximately 5.4 litres 1)
.
Plain water on its own is not enough to clean
the glass and the headlights properly. We
therefore recommend using clean water with
a glass cleaning product to eliminate any
stubborn dirt (with an anti-freeze additive in
winter).
Although
your vehicle has heated windscreen
washer jets, anti-freeze should always be
added to the water in winter.
Ethanol can be used where glass cleaner with
anti-freeze is unavailable. The concentration
of ethanol must be no greater than 15 %.
However, remember that anti-freeze in this
proportion only protects down to -5 °C
(+23 °F). CAUTION
● Never mix the windscreen washing water
with anti-freeze used for the cooling system
or other additives.
● If the vehicle is equipped with a headlight
washer system, only mix a detergent that
does not damage polycarbonates with the
water. Note
When topping up the fluid, do not move the
filter from the container opening, as this
could contaminate the fluid hoses and lead to
a windscreen washer malfunction. Battery
Introduction Warning symbols on the battery
Sym
bolMeaning 
Always wear safety glasses!

Battery acid is extremely corrosive. Always wear
gloves and hearing protection!

Keep open flames, sparks, uncovered lights
and lit cigarettes away when working on the
battery!

A highly explosive mixture of gases is released
when the battery is under charge!

Keep children away from the battery!
Incorrect handling of the vehicle battery
could lead to damage. We therefore recom-mend all work on the vehicle battery be per-
formed by an authorised SEAT dealer.
Always be aware of the danger of injury and
scalding as well as the risk of accident or fire
when working on the battery and the electri-
cal system. Therefore, always observe the
warnings and follow all general safety pre-
cautions.
WARNING
● Battery acid is very corrosive, therefore, the
battery must be handled with the utmost
care. Wear protective gloves and protect your
eyes and skin when handling batteries. The
corrosive fumes in the air irritate and inflame
the respiratory tract and cause conjunctivitis.
It corrodes tooth enamel. Causes deep and
difficult-to-heal wounds when it comes in
contact with the skin. Repeated contact with
diluted acids causes skin disease (inflamma-
tion, ulcers and fissures). When in contact
with water, acids dilute and develop a great
deal of heat.
● Do not tilt the battery, as acid could leak
out of the vapour vents. Protect your eyes
with glasses or a protective helmet! Risk of
blindness! If acid should splash into the
eyes, rinse the affected eye immediately for
several minutes using clean water. Then seek
medical care immediately. 1)
Valid only for certain countries. 5.4 litres for both
versions.
140

Advice
How to jump start: description Fig. 129
Diagram of connections for vehicles
without Start Stop system Fig. 130
Diagram of connections for vehicles
with Start Stop system Jump lead terminal connections
1. Switch off the ignition of both vehicles
››› . 2. Connect one end of the
red jump lead to
the po s
itive + terminal of the vehicle
with the flat battery A
››› Fig. 129 .
3. C

onnect the other end of the red
jump
lead to the positive terminal + in the ve-
hicle providing assistance B .
4. For vehicles without Start-Stop system:
connect one end of the black jump lead to
the negative terminal – of the vehicle
providing the current B
››› Fig. 129 .
– For

vehicles with Start-Stop system: con-
nect one end of the black jump lead X to a
suitable ground terminal, to a solid piece of
metal in the engine block, or to the engine
block itself ››› Fig. 130 .
5. C

onnect the other end of the black jump
lead X to a solid metal component bolted
to the engine block or to the engine block
itself of the vehicle with the flat battery.
Do not connect it to a point near the bat-
tery A .
6. Position the leads in such a way that they cannot come into contact with any moving
parts in the engine compartment.
Starting
7. Start the engine of the vehicle with the boosting battery and let it run at idling
speed. 8. Start the engine of the vehicle with the flat
battery and wait 2 or 3 minutes until the
engine is “running”.
Removing the jump leads
9. Before you remove the jump leads, switch off the dipped beam headlights (if they
are switched on).
10.Turn on the heater blower and heated rear window in the vehicle with the flat battery.
This helps minimise voltage peaks which
are generated when the leads are discon-
nected.
11. When the engine is running, disconnect
the l e
ads in reverse order to the details
given above.
Connect the battery clamps so they have
good metal-to-metal contact with the battery
terminals.
If the engine fails to start, switch off the start-
er after about 10 seconds and try again after
about 1 minute. WARNING
● Please note the safety warnings referring to
working in the engine compartment
››› page 132.
● The b att

ery providing assistance must have
the same voltage as the flat battery (12V) and
approximately the same capacity (see imprint 158

Advice
● Replace the cover again or close the fuse
box lid. CAUTION
If you replace a fuse with higher-rating fuse,
you could cause damage to another part of
the electrical system. Changing bulbs
Introduction Changing bulbs requires a certain degree of
practical skill. If in doubt, we recommend you
have defective bulbs changed by a special-
ised service or, in case of an emergency,
seek professional assistance.
●
Switch off the ignition and all of the lights
before changing a bulb.
● Do not touch the glass part of the bulb with
your bare hands. The fingerprints left on the
glass will vaporise as a result of the heat gen-
erated by the bulb, reducing bulb life and
causing condensation on the reflector sur-
face, thus reducing effectiveness.
● A bulb must only be replaced by one of the
same type. The type is indicated on the bulb,
either on the glass part or on the base.
● There is a storage area for the bulb box in
the spare wheel well or below the carpet in
the luggage compartment. The light source used for each function is lis-
ted below:
Double headlights
H7 Long Life
H7
W5W Long Life PY21W NA P21W Super Long Life WARNING
● Take particular care when working on com-
ponents in the engine compartment if the en-
gine is warm. Risk of burns.
● Bulbs are highly sensitive to pressure. The
glass can break when you touch the bulb,
causing injury.
● The high voltage element of gas discharge
bulbs* (xenon light) must be handled correct-
ly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not
to injure yourself on sharp parts in the head-
light housing. CAUTION
● Remove the ignition key before working on
the electric system. Otherwise, a short circuit
could occur.
● Switch off the lights and the parking light
before changing a bulb. Dipped beam:
Main beam:
Side lights:
Turn signals:
Daytime driving lights: For the sake of the environment
Please ask your specialist retailer how to dis-
pose of used bulbs in the proper manner. Note
● Depending on weather conditions (cold or
wet), the front lights, the fog lights, the rear
lights and the turn signals may be temporari-
ly misted. This has no influence on the useful
life of the lighting system. By switching on
the lights, the area through which the beam
of light is projected will quickly be demisted.
However, the edges may continue to be mis-
ted.
● Please check at regular intervals that all
lighting (especially the exterior lighting) on
your vehicle is functioning properly. This is
not only in the interest of your own safety,
but also that of all other road users.
● Before changing a bulb, make sure you
have the correct new bulb.
● Do not touch the glass part of the bulb with
your bare hands, use a cloth or paper towel
instead. Otherwise, the fingerprints left on
the glass will vaporise as a result of the heat
generated by the bulb, they will be deposited
on the reflector and damage its surface. 166

Fuses and bulbs
Double headlight bulbs Fig. 143
Main headlight bulbs. Installation position of double headlight
bulbs
Side lights
Main beam headlights
Dipped beam headlights
Turn signal lights
Daylight
A B
C
D
E Changing side light bulbs
Fig. 144
Changing side light bulbs. –
Raise the bonnet.
– Remove the protective cover ››› Fig. 144 .
– Remo
ve the bulb holder ››› Fig. 144 1 by
pulling it outwards.
– Remove the bulb by pulling it out and fit
the new one.
– Installation involves all of the above steps
in reverse sequence.
– Fit the protective cover. Make sure that the
cover fits correctly on the housing during
operation.
– Check whether the new bulb is working. Changing main beam headlight bulbs
Fig. 145
Changing main beam headlight
bulbs. –
Raise the bonnet.
– Remove the protective cover.
– Remove connector ››› Fig. 145 1 by pulling
outward.
– Extract the bulb and fit the replacement so
that it fits correctly into the recess on the
reflector.
– Installation involves all of the above steps
in reverse sequence.
– Fit the protective cover. Make sure that the
cover fits correctly on the housing during
operation.
– Check whether the new bulb is working.
167
Technical specifications
Advice
Operation
Safety

Index
C
Car computer see multi-function display . . . . . . . . . . . . . . . . . 39
Care of the vehicle . . . . . . . . . . . . . . . . . . . . . . . . 122
Care of vehicle automatic car wash . . . . . . . . . . . . . . . . . . . . . 124
cleaning chrome . . . . . . . . . . . . . . . . . . . . . . . . 125
cleaning wheels . . . . . . . . . . . . . . . . . . . . . . . . 126
headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
high-pressure cleaners . . . . . . . . . . . . . . . . . . 124
leatherette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
natural leather . . . . . . . . . . . . . . . . . . . . . . . . . 127
plastic parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
polishing of paintwork . . . . . . . . . . . . . . . . . . . 125
rubber seals . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
upholstery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
washing by hand . . . . . . . . . . . . . . . . . . . . . . . 124
waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . 105
Central locking button . . . . . . . . . . . . . . . . . . . . . . 56
Central locking system . . . . . . . . . . . . . . . . . . . . . . 54 locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Changing a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
wiper blades . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Changing bulbs double headlight bulbs . . . . . . . . . . . . . . . . . . 167
front fog light bulbs . . . . . . . . . . . . . . . . . . . . . 169 Changing gear
recommended gear . . . . . . . . . . . . . . . . . . . . . . 32
Charging the battery . . . . . . . . . . . . . . . . . . . . . . 142
Checking battery acid level . . . . . . . . . . . . . . . . . . . . . . . 142
brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
windscreen washer . . . . . . . . . . . . . . . . . . . . . . 139
Checking fluid levels engine compartment . . . . . . . . . . . . . . . . . . . . 134
Childproof locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Child safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Child seat Categorisation in groups . . . . . . . . . . . . . . . . . . 26
Child seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 ISOFIX system . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
safety instructions . . . . . . . . . . . . . . . . . . . . . . . 25
securing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Top Tether system . . . . . . . . . . . . . . . . . . . . . . . . 27
Cigarette lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
leatherette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
natural leather . . . . . . . . . . . . . . . . . . . . . . . . . 127
plastic parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
upholstery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Cleaning chrome see care of vehicle . . . . . . . . . . . . . . . . . . . . . . 125
Climatronic air recirculation . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Coat hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Compartments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Computer
see multi-function display . . . . . . . . . . . . . . . . . 39
control lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Control lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Controls and displays summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
coolant temperature display . . . . . . . . . . . . . . . . . . . . . . 31
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
topping up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Correct adjustment of front seat head restraints . . 8
Correct adjustment of rear seat head restraints In-use and non-use positions . . . . . . . . . . . . . . 10
Correct sitting position front passenger . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Incorrect sitting position . . . . . . . . . . . . . . . . . . . 9
passenger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
D Dangers in not using the seat belt . . . . . . . . . . . . 13
Dashboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Dash panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 see dash panel . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Data sticker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Daytime driving light . . . . . . . . . . . . . . . . . . . . . . . 62
Defrosting rear window . . . . . . . . . . . . . . . . . . . . . 67
Diesel fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
see fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Diesel fuel winter driving . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Digital clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
188