2014 PORSCHE 911 TURBO ignition

196 Storage, Luggage Compartment and Roof Transport System
Cigarette Lighter
The tip of the cigarette lighter becomes very hot in use.fDo not leave children in the vehicle unattended.fNever touch the heating element or sides of the lighter.fOnly hold the heated lighter by the knob.
Using the cigarette lighter
The cigarette lighter is ready for use regardless of ignition lock position.fFor information on using charging adapters in the cigarette lighter:Please see the chapter “USING CHARGING ADAPTER FOR 12 VOLT SOCKET/CIGARETTE LIGHTER” on page 197. 1. Press briefly on the ashtray lid. 2. Press the lighter into the receptacle. When the element is red hot, the lighter will jump back to its initial position.
Sockets in the glove box and passenger footwell
Sockets
Electrical accessories can be connected to the 12 V sockets. Depending on the vehicle equipment, these sockets are located in the glove box, the passenger footwell and in the oddments tray in the center console.fFor information on using charging adapters in 12 volt sockets:Please see the chapter “USING CHARGING ADAPTER FOR 12 VOLT SOCKET/CIGARETTE LIGHTER” on page 197.
Information
The maximum electrical load of a socket is 20 A, but only if no other loads are switched on. Do not exceed 10 A per socket if several loads are operating simultaneously.
Cigarette Lighter BurnsWARNINGh
14_991_Turbo_21.book Seite 196 Mittwoch, 9. April 2014 2:19 14

Storage, Luggage Compartment and Roof Transport System 197
Socket in the oddments tray between the front seats
Information
The sockets and thus the connected electrical accessories function even if the ignition is switched off or the ignition key is removed.
If the engine is not running and the accessories are switched on, the vehicle battery will be discharged. The power supply is interrupted after 30 minutes to protect the vehicle battery. If the load is to be switched on again, the ignition must be switched on once.
A - Suitable charging adapter B - Unsuitable charging adapter
Using charging adapter for 12 volt socket/cigarette lighter
Risk of damage to the electrical system.fOnly use a suitable charging adapter ( A) that meets the following requirements:The distance 1 between the ground connection and the upper edge of the charging adapter must be less than approx. 0.63 in. (16 mm).
Unsuitable charging adapters ( B) with a larger distance 1 than 0.63 in. (16 mm) between the ground connection and the upper edge can destroy the sockets.
Luggage Compartment
fPlease see the chapter “OPENING AND CLOSING THE LUGGAGE COMPARTMENT LID AND ENGINE COVER” on page 24.
NOTICE
14_991_Turbo_21.book Seite 197 Mittwoch, 9. April 2014 2:19 14

Parking 207
ParkAssist
When the driver is parking and maneuvering the vehicle, ParkAssist indicates the distance between the vehicle and a large obstacle by means of signal tones.fOn vehicles with front and rear sensors:For information on the ParkAssist visual display, please refer also to the section “PARKASSIST” in the operating instructions for the Porsche Communication Systems PCM/CDR.
ParkAssist is activated automatically when reverse gear is selected and the ignition is on.
If the vehicle has front ParkAssist, this also issues an automatic warning when the distance between the vehicle and an obstacle in front is less – than approx. 40 in./100 cm (acoustically) and approx. 32 in./80 cm (visually).
A warning signal sounds when – the distance between the vehicle and an obstacle at the rear is less than approx. 71 in./180 cm.The ParkAssist visual display appears on the central screen of the Porsche communication system.
Front and rear ParkAssist is not activated: – At a speed of more than approx. 9 mph (15 km/h).– When the electric parking brake is activated.– When the ParkAssist has been switched off with button A in the overhead console with the ignition switched on. The indicator light in button A lights up.
Responsibility for parking and for assessing the risk to persons, children, pets, and small objects around the vehicle lies completely with the driver. fMake sure that no persons (especially small children), animals or obstacles are within the maneuvering area. fIf the continuous tone sounds, stop and do not move your vehicle further in that direction.
Ultrasound sensors
Sensors
The ultrasound sensors A in the rear bumper and the sensors A in the front bumper (depending on vehicle equipment) measure the distance to the closest obstacle:– Range behind the vehicle: approx. 71 in. (180 cm)– Range at the side of the vehicle: approx. 24 in. (60 cm)– Range in front of the vehicle: approx. 47 in. (120 cm)
Obstacles cannot be detected in the “blind” sensor area (above and below the sensors, e.g. objects hanging down or close to the ground).
ParkAssist LimitsWARNINGh
14_991_Turbo_21.book Seite 207 Mittwoch, 9. April 2014 2:19 14

210 Parking
Swivelling Down Mirror Glass as
Parking Aid
When reverse gear is engaged, the mirror on the passenger’s side swivels down slightly to show the curb area.
Preconditions
– The ignition must be switched on. – The function must be activated on the multi-function display.
For further information on setting the parking aid:fPlease see the chapter “ADJUSTING REVERSING OPTIONS” on page 122.
Swivelling down mirror glass manually
If the function was deactivated on the multi-function display, the exterior mirror on the passenger’s side can also be swiveled down manually.1. Engage reverse gear. The indicator light B on the selection button A for adjusting the exterior mirror on the driver’s side lights up.2. Press the selection button D for adjusting the exterior mirror on the passenger’s side.The mirror on the passenger’s side swivels down.
Information
The position of the automatically lowered mirror glass can be changed as required using the adjustment button C. On vehicles with memory package, the setting is stored on the car key or the person buttons on the driver’s side.
Moving mirror to its initial position
The mirror swivels back to its initial position: – after a certain time delay, if the vehicle is shifted out of reverse gear, or – immediately, if the vehicle reaches a speed of more than 9 mph (15 km/h).
The exterior mirror on the passenger’s side can also be moved to its initial position manually.fPress the selection button A for the exterior mirror on the driver’s side.
14_991_Turbo_21.book Seite 210 Mittwoch, 9. April 2014 2:19 14

212 Parking
Operating the garage door opener
The ignition must be switched on.fPress and hold the corresponding HomeLink® button on the overhead operating console keypad.The indicator light A lights up during signal transmission.
Programming garage door opener: Deleting and storing signals
The HomeLink® system is programmed on the overhead operating console and in direct proximity to the vehicle’s radiator grille.
Preconditions
In order to delete programmed signals and store garage door opener signals,– the ignition must be switched on,– the turn signals must be off and – the engine must be off.
When using the garage door opener, the vehicle must be within the range of the receiver.
Deleting programmed signals from the buttons
This process clears all of the HomeLink® programming. It is not possible to individually clear the programmed buttons.Do not repeat this process if you want to assign additional signals to the buttons.fKeep the two outer buttons I and III on the overhead operating console keypad pressed for approx. 20 seconds until the indicator light A on button II starts to flash quickly.fRelease the buttons.
The HomeLink® buttons are cleared and can be reprogrammed.
Assigning garage door opener signal to key with fixed code system
On the overhead operating console: 1. Switch on ignition. 2. The standard factory-set codes must be deleted before programming for the first time . 3. Press and hold the desired button on the overhead operating console keypad until the indicator light A on button II starts to flash slowly.You now have 5 minutes to teach the button.4. Stand in front of the vehicle with the original remote control of the system to be programmed.
14_991_Turbo_21.book Seite 212 Mittwoch, 9. April 2014 2:19 14

Parking 213
In front of the vehicle: 5. Hold the original remote control approx. 8 in. (20 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A on the overhead operating console starts flashing quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
6. The turn signal lights will flash once when the 5 minute teaching readiness period has elapsed.Repeat steps 3 to 5.7. Repeat steps 3 to 5 to assign further signals to the remaining buttons.
Assigning garage door opener signal to button with changeable code system
With some systems, a changeable code also needs to be programmed for the HomeLink® system. A second person makes programming easier.
Identifying the changeable code
fPress and hold the previously programmed HomeLink® button.
If the indicator light A on button II in the overhead operating console starts to flash quickly and lights up continuously after approx. 2 seconds, it means that the equipment has a changeable code system.fInformation on synchronization can also be found in the operating instructions for the system to be programmed.
Assigning garage door opener signal to key
fPark the vehicle within the range of the remote- controlled equipment.
On the overhead operating console: 1. Switch on ignition. 2. The standard factory-set codes must be deleted before programming for the first time.
For information on deleting the factory-set codes:fPlease see the chapter “PROGRAMMING GARAGE DOOR OPENER: DELETING AND STORING SIGNALS” on page 212.3. Press and hold the desired button on the overhead operating console keypad until the indicator light A on button II starts to flash slowly.You now have 5 minutes to teach the button.4. Stand in front of the vehicle with the original remote control of the system to be programmed.
In front of the vehicle: 5. Hold the original remote control approx. 12 in. (30 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A on the overhead operating console starts flashing quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
14_991_Turbo_21.book Seite 213 Mittwoch, 9. April 2014 2:19 14

214 Parking
6.The turn signal lights will flash once when the 5 minute teaching readiness period has elapsed.Repeat steps 3 to 5.7. Repeat steps 3 to 5 to assign further signals to the remaining buttons. 8. Locate the programming button on the receiver of the equipment to be programmed, e.g. on the motor unit of the garage door opener.
Synchronizing the system
9. Activating the motor unit: Press the programming button on the receiver of the garage door opener.You then usually have approx. 30 seconds to initiate step 10 (a setting indicator is usually activated on the motor unit).10. Programming on the overhead operating console:Press the button you selected in step 3 three times on the overhead operating console keypad (you must press the button on the keypad several times to complete the setting process for some devices).11. Repeat steps 3 to 10 to assign signals to the other buttons.12. After completing programming on the overhead operating console, the system should recognize the HomeLink® signal and launch as soon as the memory button is pressed when the ignition is switched on.
Reprogramming an individual button on the keypad
A HomeLink® button can be individually reprogrammed without deleting the rest of the button assignments.
On the overhead operating console: 1. Switch on ignition. 2. Press and hold the button to be programmed on the overhead operating console keypad (approx. 20 seconds), until indicator light A on button II flashes slowly. You now have 5 minutes to teach the button.3. Stand in front of the vehicle with the original remote control of the system to be programmed.
In front of the vehicle: 4. Hold the original remote control approx. 12 in. (30 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A in the overhead operating console starts to flash quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
5. The turn signal lights will flash once when the 5-minute teaching readiness period has elapsed.Repeat steps 1 to 4.6. Repeat steps 1 to 4 to assign further signals to the other buttons.
Information
fPlease consult an authorized Porsche dealer if you have not been able to successfully assign signals to the buttons even though you have carefully followed the instructions in this section and the operating instructions for the original remote control. Your authorized Porsche dealer has a list of all garage door opener signals that can be adapted.fMake sure that the battery in the remote control for the garage door opener is new. If the battery voltage is inadequate, faults may occur in signal transmission. The system in the vehicle then learns the wrong code, which will not be recognized reliably by the garage door opening mechanism.
14_991_Turbo_21.book Seite 214 Mittwoch, 9. April 2014 2:19 14

216 Alarm System and Theft Protection
Alarm System and Passenger
Compartment Monitoring
FCC Numbers :
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation of this device is subject to the following two conditions:1. This device may not cause harmful interference, and 2. this device must accept any interference received including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modification could void the user's authority to operate the equipment.
The alarm system monitors the following alarm contacts:– Alarm contacts in doors, luggage compartment lid, engine compartment lid and headlights.– Interior surveillance: Movement in the interior when the vehicle is locked, e.g. attempted theft after breaking a window.– Inclination sensor country-specific equipment: inclination of the vehicle (e.g. when attempting to tow).
If one of these alarm contacts is interrupted, the alarm horn sounds for approx. 30 seconds and the emergency flasher flashes.After 5 seconds of interruption, the alarm is triggered again. This cycle is repeated up to ten times.
Switching on
fThe alarm system is activated when the vehicle is locked.
Switching off
fThe alarm system is deactivated when the vehicle is unlocked.
Information
fIf you unlock the vehicle with the emergency key in the door lock, you must switch the ignition on (ignition lock position 1) within 10 seconds of opening the door in order to prevent the alarm system from being triggered.
Information
If button on the car key is pressed and a door or the luggage compartment lid is not opened, the vehicle is locked again automatically after 30 seconds.
Switching off the alarm system if it is triggered
fUnlock vehicle or switch on ignition.
Switching off interior surveillance and inclination sensor
If people or animals are remaining in the locked vehicle or the vehicle is being transported on, e.g. a train or ship, the interior surveillance system and inclination sensor must be switched off temporarily.fInform any persons remaining in the vehicle that the alarm system will be triggered if the door is opened.
Using the car key
fQuickly press button on the car key twice within 2 seconds.The emergency flasher flashes slowly once.The doors are locked, but can be opened from inside.
USA: KR55WK50138
Canada: 7812D-5WK50138
14_991_Turbo_21.book Seite 216 Mittwoch, 9. April 2014 2:19 14