2014 PORSCHE 911 TURBO air condition

60 Air Conditioning
Heated Rear Window/
Exterior Mirror Heating
Heated rear window/exterior mirror heating is ready for operation when the engine is running.
Switching on
fPress button .The indicator light on the button lights up.
Depending on the outside temperature, the heating switches off automatically after approx. 5 to 20 minutes.fThe heating can be switched back on by pressing the button again.
Switching off
fPress button .The indicator light on the button goes out.
If the charging condition of the battery is critical, the heated rear window/exterior mirror heating function is restricted initially and then switched off.
14_991_Turbo_21.book Seite 60 Mittwoch, 9. April 2014 2:19 14

Lights, Turn Signals and Windshield Wipers 83
Switching on and off (on vehicles WITH High Beam Assistant)
If the High Beam Assistant was deactivated or if the requirements are not met, high beam can be switched on and off manually.
The following conditions must be met: – Darkness– The light switch position is selected.fSwitching on : Push the stalk twice to the front pressure point 3. The indicator light on the tachometer lights up.fSwitching off : Push the stalk once to the rear pressure point 4.
Operating the headlight flasher
fPush the stalk once to the rear pressure point 4. The indicator light on the tachometer lights up briefly.
For information on High Beam Assistant: fPlease see the chapter “HIGH BEAM ASSISTANT” on page 81.
Parking light
The parking light can only be switched on when the ignition is switched off.fMove the stalk up 2 or down 1 to switch on the right or left parking light.
If the parking light is switched on, the message “ Parking light on” will appear on the multi- function display in the instrument panel after the ignition is switched off.
For information on warning messages on the multi- function display:fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Emergency Flasher
The emergency flasher can be switched on regardless of the position of the ignition lock.
Switching on and off
fPress the emergency flasher button on the center console.
All turn signal lights and the indicator light in the button flash when the button is operated.
If the emergency flasher remains active for longer periods, the illumination phase of the flashing interval is shortened to preserve the lights.
Other vehicles could collide with your vehicle if you are parked in a dangerous position.fWhenever stalled or stopped for emergency repairs, move the car well off the road. Switch on the emergency flasher and mark the car with road flares or other warning devices.fDo not remain in the car. Someone approaching from the rear may not realize your vehicle is stopped and cause a collision.
Exhaust fumes and the exhaust system are very hot when the engine is running. The exhaust system (including the tailpipe) remains hot for some time after the vehicle is turned off.fDo not park or operate the vehicle in areas where the hot exhaust system may come in contact with dry grass, brush, fuel spill or other flammable material.
The engine and surrounding components become very hot when the engine is running.fBefore working on any part in the engine compartment, turn the engine off and let it cool down sufficiently.
Emergency Stopping
Hot Exhaust System and Tailpipe
Engine Heat Danger When Working
DANGERh
WARNINGh
WARNINGh
14_991_Turbo_21.book Seite 83 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 99
Info
Oil measurement LimitsSettings
Station/Track
Answer/Reject/End
Phonebook
Previous calls
Received calls
Manual zoom Auto zoom3D map North up
Show destination/position
Destination input
Start/Stop route guidance
Since
Total
To destination
Fill info Tire typePartial/full load Comfort/standard pressure
Start StopRoundInt.
Torque
Current speed
Setting the speed
Menu scope
Audio
Vehicle menu
Upper line
PCM display
Lower line
Shift request
Brightness
Exterior lights
Interior lights
Wiper
Revers. opt.
Door lock/unlock
Comfort Entry
Auto Memory
Air flow
Vent. panel
Auto air circ.
Time
Date
DST (+01:00)
Time Chrono
Speedometer
Temperature
Tire pressure
Consumption
German/French...
ParkAssist
Warn. tones
◊ button
Messages
Service interval
Limit 1/Limit 2
Display
Light & Visibility
Locking
Air conditioning
Date & Time
Units
Language
Volume
Steering wheel op.
Fact. settings
Last destination
Stored destinations
POIs
Cont.
Reset
Vehicle
Audio
Telephone
Map
Navigation
Trip
Tire pressure
Allwheel
Chrono
G-Force
Performance
ACC
14_991_Turbo_21.book Seite 99 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 123
Switching Auto Memory on and off
It is possible to determine whether personal settings are to be stored automatically on the car key when locking the vehicle.
For further information on storing and retrieving personal settings:fPlease see the chapter “STORING PERSONAL SETTINGS” on page 143.
Folding exterior mirrors in and out automatically
You can configure the exterior mirrors to fold in automatically when the vehicle is locked.
Setting air conditioning
The automatic air conditioning can be changed individually.
Adjusting air flow
The strength of the air flow and the air quantity can be adjusted.
Available setting options: –“ Soft” –“ Normal” –“ Strong”
Switching extended ventilation panel on and off
The extended ventilation panel on top of the dashboard can be switched on or off.
Switching automatic air-recirculation mode on/off
You can configure the fresh air supply to adjust automatically to the air quality.
1. Main menu “Vehicle” > “ Settings” > “ Locking”
2.Select “ Auto Memory”.
3.Confirm your selection.
Auto Memory is activated.
Auto Memory is deactivated.
1. Main menu: Select “Vehicle” > “ Settings” > “ Locking”
2.Select “Mirror retract”.
3.Confirm your selection.
Exterior mirrors are folded in.
Exterior mirrors are not folded in.
1. Main menu “Vehicle” > “ Settings” > “ Air conditioning” and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Air conditioning”
2.“Climate style” and confirm.
3. Select the desired setting and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Air conditioning”
2.Select “Vent. panel”. in the main menu.
3. Confirm your selection.
Ventilation panel is activated.
Ventilation panel is deactivated.
1. Main menu “Vehicle” > “ Settings” > “ Air conditioning”
2.Select “Automatic air circ.”. in the main menu.
3. Confirm your selection.
Automatic air-recirculation mode is activated
Automatic air-recirculation mode is deactivated
14_991_Turbo_21.book Seite 123 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 125
Setting the date
The date and date format can be changed in the “ Date” menu.
Setting the date format
The date format can be adjusted.
Available setting options: –“ DD.MM.YYYY” –“ MM/DD/YYYY” –“ YYYY/MM/DD”
Setting the current date
The day, month and year can be set individually on vehicles without the navigation module.
Setting Daylight Saving Time
The vehicle clock can be configured to change to Daylight Saving Time.
Displaying time in stopwatch on dashboard
You can configure the stopwatch on the dashboard to display the time.
Setting units
You can select the units of measurement for vehicle displays such as the speed on the digital speedometer in the instrument panel, the temperature gauge in the air-conditioning displays and the tire pressure display on the multi-function display.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Date” and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Date”
2.“Format” and confirm.
3. Select the desired setting and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Date” and confirm.
2. “Date”. in the main menu.
3. Set the desired date and confirm the setting.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time”
2.Select “ DST (+01:00)”
3.Confirm your selection.
Daylight Saving Time is activated.
Daylight Saving Time is deactivated.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time”
2.Select “Time – Chrono” in the main menu.
3. Confirm your selection.
Time is displayed.
Time is not displayed.
1. Main menu “Vehicle” > “ Settings” > “ Units” and confirm.
14_991_Turbo_21.book Seite 125 Mittwoch, 9. April 2014 2:19 14

142 Personal Settings
Brief Overview – Personal Settings
This brief overview does not replace the information provided under “PERSONAL SETTINGS”.
Warnings, in particular, are not replaced by this brief overview.
Storing settings automatically on the key (with “ Auto Memory” function activated) Storing settings manually on the buttons in the driver's door
Where can I store/ retrieve the settings?Which settings can I store/retrieve with the memory package?
Automatic when locking/unlocking the vehicle door via the car key. Ergonomic settings – Driver’s seat, exterior mirrors, electric steering column
Comfort settings – Air conditioning, multi-function display and Porsche Communication Management (PCM)
Prerequisite: The “ Auto Memory“ function must be activated in the multi-function display.fPlease see the chapter “SWITCHING AUTO MEMORY ON AND OFF” on page 123.
Notice : If the “Auto Memory” function is activated, the settings stored on the key or on key button are overwritten each time the vehicle is locked.
Manually, using buttons 1 and 2.Ergonomic settings – Driver’s seat, exterior mirrors, passenger's seat, electric steering column
Manually, using key button in the driver's door. Ergonomic settings – Driver’s seat, exterior mirrors, electric steering column
Comfort settings – Air conditioning, multi-function display and Porsche Communication Management (PCM)
The settings are stored on key button in the driver’s door and on the car key.
14_991_Turbo_21.book Seite 142 Mittwoch, 9. April 2014 2:19 14

Personal Settings 143
Driver's door memory buttons (comfort memory)
Storing personal settings
In conjunction with the fully-electric sports seat or the adaptive sports seat plus, a memory package is available. With the memory package, personal settings can be stored on the car key or on the memory buttons in the driver’s door.
Memory package
The memory package includes storage of ergonomic settings for – driver’s seat– electric steering column and– exterior mirrors as well as
comfort settings for – air conditioning– multi-function display and– Porsche Communication Management (PCM).
Parts of the body may be pinched or crushed if the settings are activated in an uncontrolled manner.fAutomatic retrieval of the settings can be cancelled by pressing a memory button or any seat adjustment button.fDo not leave children in the vehicle unattended.
Information
If the automatic storage function is activated on the multi-function display, the settings will be automatically stored on the car key when the vehicle is locked.
For information on switching the automatic storage function on and off: fPlease see the chapter “SWITCHING AUTO MEMORY ON AND OFF” on page 123.
Regardless of whether the automatic storage function is activated on the multi-function display, the settings can be stored on the car key (by pressing key button ) and the memory buttons 1 or 2 and retrieved from there.
Storing the settings on the car key
Ergonomic and comfort settings can be individually assigned to the car keys.
Information
Individual memory information can be stored on a total of 4 car keys. In the case of further car keys, the memory information from key 4 is adopted.
Automatic storage through locking of the vehicle.
This function must be activated on the multi- function display.fPlease see the chapter “SWITCHING AUTO MEMORY ON AND OFF” on page 123.– The settings are stored on the car key being used when the vehicle is locked.– On vehicles with Porsche Entry & Drive, settings are stored by pressing the locking button on the door handle.
In what situation is it useful to activate the “Auto Memory” function?
Each driver uses his or her own key. When locking the vehicle, the last selected settings are stored on the key. When changing drivers, the personal settings can be retrieved via the respective keys.
Retrieving automatic settings for seats, mirrors and electric steering column
CAUTIONh
14_991_Turbo_21.book Seite 143 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 149
Auto Start Stop function
The engine stops automatically when the vehicle is
stopped, e.g. at traffic lights or in a traffic jam, if all the preconditions for stopping the engine automatically are met. The engine can also stop automatically
during a stop at walking pace. The Auto Start Stop function thus helps to save fuel.
The ignition stays on even when the engine switches off automatically. All safety functions are still available.
Preconditions for stopping the engine automatically
– Auto Start Stop function switched on. – Engine compartment lid closed.– Brake pedal pressed– Move PDK selector lever to the D, N or P position, or to a manually selected transmission range 1 or 2. – Engine, transmission and air conditioning are at operating temperature.– Battery has reached its target voltage.– Vehicle was driven at a speed of more than approx. 1 mph (2 km/h) for at least 1.5 seconds since the engine last stopped automatically.
Information
When the ignition is on, the battery is discharged. If the vehicle is parked for an extended period, the battery can discharge fully and be damaged (exhaustive discharge).
Stopping the engine
The Auto Start Stop function stops the engine once the vehicle stops moving or during the stopping process.1. Use the footbrake to stop the vehicle. 2. Keep the footbrake pressed. orMove PDK selector lever to position P.
Information
– The engine can also be stopped subsequently (not immediately after the vehicle comes to a stop) if the exceptions are set aside and the preconditions for stopping the engine automatically continue to be met.fPlease see the chapter “EXCEPTIONS FOR THE AUTO START STOP FUNCTION” on page 150.– When adaptive cruise control is switched on, the engine stops automatically when the vehicle is stationary if the vehicle in front also comes to a stop.
Starting the engine
The Auto Start Stop function starts the engine:fIn PDK selector-lever position D, N or manually selected transmission range 1 or 2: Release the footbrake.orPress the accelerator.orMove the steering wheel.orMove PDK selector lever to position R.
You can drive off normally.
Information
When adaptive cruise control is switched on, the engine starts automatically if the following preconditions are met:– The vehicle in front drives off.orThe accelerator is pressed.orSpeed and distance control is resumed using the control stalk (position 4, RESUME).fPlease see the chapter “INTERRUPTING AND RESUMING CRUISE CONTROL AND DISTANCE CONTROL” on page 164.– Switching off adaptive cruise control starts the engine automatically and the vehicle moves (crawls) when in gear.
14_991_Turbo_21.book Seite 149 Mittwoch, 9. April 2014 2:19 14