2014 Peugeot RCZ turn signal

30
Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the
corresponding system has come into operation.
It may be accompanied by an audible signal.
Depending on your version of instrument panel, illumination of the
indicator lamp may also be accompanied by:
- a symbol in the central instrument panel screen and a message in the multifunction screen,
or
- a symbol and a message in the central instrument panel screen.
Warning lamp is on Cause Action / Observations
Left-hand
direction
indicato r fl ashing with
buzzer.
The lighting stalk is pushed
down.

Right-hand direction
indicator fl ashing with
buzzer. The lighting stalk is pushed up.
Hazard warning
lamps fl ashing with
audible signal. The hazard warning lamps
switch, located on the dashboard,
has been operated. The left-hand and right-hand direction indicators and their
associated indicator lamps fl ash simultaneously.
Sidelamps fi xed. The lighting stalk is in the
"Sidelamps" position or the
"AUTO" position with low light.
Dipped beam
headlamps fi xed. The lighting stalk is in the
"Dipped beam headlamps"
position or in the "AUTO" position
in conditions of low light.
Main beam
headlamps fi xed. The lighting stalk is pulled
towards you. Pull the stalk again to return to dipped beam
headlamps.

1/
MONITORING
COOLANT TEMPERATURE INDICATOR
With the engine running, when the needle is:
- in zone A , the temperature is correct,
- in zone B , the temperature is too high; the maximum temperature warning lamp and the central STOP warning lamp come on,
accompanied by an audible signal and an alert message in the
screen.
You MUST stop as soon as it is safe to do so.
Wait a few minutes before switching off the engine.
Contact a PEUGEOT dealer or a qualifi ed workshop.
ENGINE OIL LEVEL INDICATOR
This information is displayed for a few seconds when the ignition is
switched on, at the same time as the service information.
The check of this level is only valid if the vehicle is on a level
surface, with the engine having been off for more than 30 minutes.
After driving for a few minutes, the temperature and pressure in the
cooling system increase.
To top up the level:
 wait for the engine to cool,
 unscrew the cap by two turns to allow the pressure to drop,
 when the pressure has dropped, remove the cap,
 top up the level to the "MAX" mark.

2/
ACCESS
Folding the key
 First press this button to fold the key.
LOCATING YOUR VEHICLE
REMOTE CONTROL PROBLEM
Following disconnection of the vehicle battery, replacement of the
remote control battery or in the event of a remote control malfunction, \
you can no longer unlock, lock or locate your vehicle.
 First of all, use the key in the lock to unlock or lock your vehicle.
 Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT dealer as soon as
possible.
Reinitialisation
 Switch off the ignition.
 Turn the key to position 2 (Ignition on) .
 Press the closed padlock immediately for a few seconds.
 Switch off the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620 / 3 volts.
If the battery is fl at, you are informed by illumination of this
warning lamp, accompanied by an audible signal and an alert
message in the screen.
 Unclip the casing using a coin at the notch.
 Slide the fl at battery out of its location.
 Slide the new battery into its location observing the original direction.
 Clip the casing.
 Reinitialise the remote control.
This function allows you to identify your vehicle from a
distance, particularly in poor light. Your vehicle must be
locked.
 Press the closed padlock on the remote control.
This will switch on the courtesy lamps and the direction indicators will\

fl ash for around ten seconds.

4/
VISIBILITY
RCZ_EN_CHAP04_VISIBILITE_ED02-2013

C. Foglamp selection ring.
The foglamp operates with the dipped and main beam headlamps. Rear foglamp.
 Turn the ring C forwards and release to switch on the rear foglamp.
When the lighting is switched off automatically (with AUTO model)
or when the dipped beam headlamps are switched off manually, the
foglamp and the sidelamps will remain on.
 Turn the ring C rearwards and release to switch off all the lamps. In good or rainy weather, both day and night, use of the rear
foglamp is prohibited. In these situations, the power of its beam
may dazzle other drivers. It should only be used in fog or snow.
In these weather conditions, it is your responsibility to switch
on the foglamp and dipped beam headlamps manually as the
sunshine sensor may detect suffi cient light.
Do not forget to switch off the rear foglamp when it is no longer
needed.
Switching off the lamps when the ignition is switched off
On switching off the ignition, all of the lamps turn off immediately,
except for dipped beam if guide-me-home lighting is activated.
Switching on the lamps after the ignition is switched off
To reactivate the lighting control, rotate ring
A to the "0" position -
lamps off, then to the desired position.
On opening the driver's door a temporary audible signal warns the
driver that the lighting is on.
The lamps, with the exception of the sidelamps, switch off
automatically after a maximum duration of thirty minutes to
prevent discharging of the battery.

5/
SAFETY
RCZ_EN_CHAP05_SECURITE_ED02-2013
Deactivation
In exceptional conditions (starting a vehicle which is bogged down,
stuck in snow, on soft ground...), it may be advisable to deactivate the
DSC and ASR, so that the wheels can turn freely and regain grip.
Reactivate the systems as soon as the level of grip permits.
 Press this button.
The indicator lamp in the button comes on.
The DSC and ASR systems no longer act on the operation of the engine
and on the brakes in the event of a involuntary change of trajectory.
This action also deactivates the automatic operation of hazard warning
lamps (except for the 1.6 litre THP 270 hp version).
Reactivation
The systems are reactivated automatically each time the ignition is
switched back on.
You can also reactivate them manually:
 Press this button again.
This action also reactivates the automatic operation of hazard warning
lamps (except for the 1.6 litre THP 270 hp version).
Operating fault DSC/ASR
The DSC and ASR systems offer increased safety in normal
driving, but they should not encourage the driver to take extra
risks or drive at high speed.
It is in diffi cult driving conditions (rain, snow, ice) that the risk of
loss of grip increases. It is therefore important for your safety to
keep the DSC and ASR systems activated in all conditions, and
particularly in diffi cult conditions.
The correct operation of these systems depends on observation
of the manufacturer's recommendations regarding as much the
wheels (tyres and rims), braking and electronic components as the
assembly and repair procedures used by PEUGEOT dealers.
To benefi t in full from the effectiveness of the DSC and ASR
systems in wintry conditions, the vehicle must be fi tted with four
snow tyres, allowing the the vehicle to retain neutral behaviour on
the road. Illumination of this warning lamp and the lamp in the
deactivation button, accompanied by an audible signal and a
message, indicate a fault with the system.
Contact a PEUGEOT dealer or a qualifi ed workshop to have the system
checked.
After an impact, have these systems checked by a PEUGEOT
dealer or a qualifi ed workshop.

108
RCZ_EN_CHAP05_SECURITE_ED02-2013
Before operating the spoiler, ensure that no one is in the proximity
of the moving parts to avoid any risk of injury.
Nevertheless, in the event of pinching, you must reverse the
movement of the spoiler. To do this, release the control button
then press it again to raise the spoiler.
MAINTENANCE
To maintain the spoiler, with the vehicle stationary, ignition on:
 raise the spoiler to the maximum position B by pressing the
button briefl y,
 once the cleaning is complete, retract the spoiler: press and hold the button until the end of the manoeuvre.
The keep this system in good working order, check the spoiler and its
housing periodically preventing the unwanted accumulation of leaves,
ice or snow.
OPERATING FAULT
If the control system fails, the indicator lamp in the control button
fl ashes, accompanied by an audible signal and a message in the
screen. As a safety precaution, the spoiler rises to the maximum
position, regardless of the speed of the vehicle.
If the problem persists and you wish to retract the spoiler:
 stop where it is safe to do so,
 switch off the ignition,
 switch the ignition on again.
If the indicator lamp no longer fl ashes, the failure was temporary, the
system has resumed normal operation. To retract the spoiler, refer to
the paragraph "To exit from manual mode".
If the indicator lamp fl ashes again and the spoiler is still raised, the
system is still faulty.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
In the event of a system operating fault (e.g. jamming of the spoiler)\
, the
indicator lamp in the control button fl ashes, accompanied by an audible
signal and a message in the screen. For safety reasons, do not exceed
a speed of 85 mph (140 km/h).
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
Before washing the vehicle, always retract the spoiler into its
housing.
Keep the end of the high-pressure nozzle at least 1 metre from the
spoiler housing. Never press on the spoiler to close the boot or push the vehicle as
this may damage it.
The installation of load-carrying accessories on the vehicle limits
the effectiveness of the spoiler.
Do not install load carrying accessories which are not
recommended by PEUGEOT.
To exit from manual mode:
 press the button briefl y: the indicator lamp on the button goes off
(return to automatic mode).
At speeds below 6 mph (10 km/h), the spoiler stays in the open
position. It retracts automatically as soon as the vehicle exceeds
this speed threshold.

6/
DRIVING
IGNITION SWITCH
ELECTRONIC ENGINE IMMOBILISER
STARTING THE VEHICLE
 Insert the key in the ignition switch.
The system recognises the starting code.
 Turn the key fully towards the dashboard to position 3 (Starting) .
 When the engine starts, release the key.
SWITCHING THE VEHICLE OFF
 Immobilise the vehicle.
 Turn the key fully towards you to position 1 (Stop) .
 Remove the key from the ignition switch.
Key left in the "Ignition on" position
On opening the driver's door, an alert message is displayed,
accompanied by an audible signal, to remind you that the key is
still in the ignition switch at position 1 (Stop) .
If the key has been left in the ignition switch at position 2 (Ignition
on) , the ignition will be switched off automatically after one hour.
To switch the ignition back on, turn the key to position 1 (Stop) ,
then back to position 2 (Ignition on) .
The key contains an electronic chip which has a special code. When
the ignition is switched on, this code must be recognised in order for
starting to be possible.
A few minutes after the ignition is switched off, this electronic engine
immobiliser locks the engine management system and prevents starting
of the engine by anyone who does not have the key.
In the event of a malfunction, you are informed by lighting of this
warning lamp, an audible signal and a message on the screen.
In this case, your vehicle does not start; contact a PEUGEOT
dealer as soon as possible.
Switching off the engine leads to a loss of braking assistance.

3
3
134
DISPLAYS IN THE INSTRUMENT PANEL
When you move the lever in the gate to select a position, the
corresponding symbol is displayed in the instrument panel.
P. Park
R. Reverse
N. Neutral
D1... D6. Drive (Automatic driving)
S. Sport programme
 . Snow programme
M1... M6. Manual (Sequential driving)
-. Invalid value during manual operation
MOVING OFF
 Apply the parking brake.
 Select position P or N .
 Start the engine.
If this procedure is not followed, there is an audible signal, accompanied
by a message in the screen.
 With the engine running, press the brake pedal.
 Release the parking brake.
 Select position R , D or M ,
 Gradually release the brake pedal.
The vehicle then moves off.
If position N is engaged inadvertently while driving, allow the
engine to return to idle then engage position D to accelerate.
When the engine is running at idle, with the brakes released, if
position R , D or M is selected, the vehicle moves even without the
accelerator being pressed.
When the engine is running, never leave children in the vehicle
without supervision.
When carrying out maintenance with the engine running, apply the
parking brake and select position P .
A message is displayed if you try to move the gear lever from
position
P without pressing the brake pedal.