Page 35 of 368
1
33
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
Fault with the "Keyless Entry and
Starting" system. Contact a PEUGEOT dealer.
Fault with the electronic anti-theft
system. Switch off the ignition, then start
the engine. If the problem persists, contact a
PEUGEOT dealer.
The electronic key is not detected. Insert the electronic key into the
housing located in the glove box. Remember to remove the electronic
key from the housing after starting
the vehicle.
The electronic key has not been
removed from the housing in the
glove box. Remove the electronic key from the
housing in the glove box.
The steering column is locked. Switch the ignition on and turn the
steering wheel slightly to unlock the
steering column.
The engine is off but the gear lever
is not in position P
. Place the gear lever in position P
. Only for vehicles fitted with a "CVT"
gearbox.
Page 36 of 368
34
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
The steering column has not locked
after opening the driver's door. Lock the steering column by turning
the steering wheel slightly before
leaving the vehicle.
Fault with the electrical system. Contact a PEUGEOT dealer or
a qualified workshop.
Page 40 of 368
38
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
You have moved off with the parking
brake not fully released. Release the parking brake.
The oil pressure is too low or there
is a fault with the engine lubrication
system. Stop the vehicle and contact
a PEUGEOT dealer or a qualified
workshop.
Battery charge fault. Stop the vehicle and contact
a PEUGEOT dealer or a qualified
workshop.
Airbag or pretensioner fault. Contact a PEUGEOT dealer or
a qualified workshop to have the
systems checked.
Fault with automatic headlamp
adjustment system. Contact a PEUGEOT dealer or
a qualified workshop. Only on vehicles fitted with xenon
headlamps.
Fault with the stability control
system (ASC). Contact a PEUGEOT dealer or
a qualified workshop.
Fault with the four wheel drive
transmission system. Contact a PEUGEOT dealer or
a qualified workshop.
Page 41 of 368
1
39
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
Fault with the CVT gearbox. Contact a PEUGEOT dealer or
a qualified workshop.
The temperature of the four wheel
drive transmission system is too
high. Stop the vehicle and contact
a PEUGEOT dealer or a qualified
workshop. The vehicle changes automatically
to two wheel drive (2WD).
The fuel level is low. Refuel as soon as possible.
The low level of the particle
emissions filter additive reser voir
has been reached. Have the reser voir topped up as
soon as possible by a PEUGEOT
dealer or a qualified workshop. Only for the 1.6 litre HDi engine.
+ Start of saturation of the particle
emissions filter. As soon as the driving conditions
allow, regenerate the filter by driving at
a speed of at least 25 mph (40 km/h)
for around 20 minutes (with the 1.6 litre
HDi engine the minimum speed is
36 mph (60 km/h)). If the message remains on,
contact a PEUGEOT or a qualified
workshop.
The particle emissions filter is
faulty. Stop as soon as it is safe to do so. Contact a PEUGEOT dealer or
a qualified workshop as soon as
possible.
Page 43 of 368
1
41
Monitoring
Screen 1
Screen 2
System
Observations
Information messages (ignition at "ON")
2WD two wheel drive
system
Flashes for a few moments when the "2WD" (2 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
4WD four wheel drive
system
Flashes for a few moments when the "4WD" (4 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
4WD LOCK four wheel
drive system
Flashes for a few moments when the "LOCK" (4 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
Active stability control
(ASC)
Flashes when the stability control system (ASC) is operating.
Page 91 of 368
89
3
Comfort
Rear view mirror
Adjustable mirror providing a central rear ward view.
Equipped with an anti-dazzle system, which darkens the mirror glass and reduces the nuisance to
the driver caused by the sun, headlamps from other vehicles...
Manual day/night model
Adjustment
)
Adjust the mirror so that the glass is
directed correctly in the "day" position.
As a safety measure, the mirrors should be adjusted to reduce the "blind spot".
In order to ensure optimum visibility
during your manoeuvres, the mirror
lightens automatically when reverse
gear is engaged.
Day / night position
)
Pull the lever to change to the "night"
anti-dazzle position.
)
Push the lever to change to the normal
"day" position.
Automatic day/night model
By means of a sensor, which measures the
light from the rear of the vehicle, this system
automatically and progressively changes
between the day and night uses.
Steering wheel adjustment
)
When stationary
, lower the control lever
to release the steering wheel adjustment
mechanism.
)
Adjust the height and reach to suit your
driving position.
)
Pull the control lever to lock the steering
wheel adjustment mechanism.
As a safety precaution, these
operations should only be carried out
while the vehicle is stationary.
Page 110 of 368
108
Driving
Starting - stopping the engine with the key
- Position 1: LOCK
The steering is locked.
- Position 2: ACC
The accessories (radio, 12 V socket...) can
be used.
- Position 3: ON
Ignition on.
- Position 4: START
Starting the engine.
Ignition switch
If you use the accessories for a
prolonged period (with the key in
position 2 (ACC)
), you risk discharging
the battery. Starting your vehicle will
then no longer be possible. Be aware
.
See the "Automatic power cut-off to
accessories" section.
Key in ignition
A buzzer sounds on opening the
driver's door, if the key has been left in
the ignition.
)
Insert the key in the ignition switch.
)
Turn the key to position 2 (ACC)
and
unlock the steering column, by turning
wheel slightly.
)
Press and hold the brake pedal.
)
Fully depress the clutch pedal (vehicles
fitted with a manual gearbox).
)
Put the gear lever into neutral (vehicles
fitted with a manual gearbox), or in
position P
(vehicles fitted with a CVT
gearbox).
)
Operate the starter by turning the key to
position 4 (START)
.
)
Once the engine is running, release the key.
The key returns automatically to
position 3 (ON)
.
Starting using the key
Stopping
)
Immobilise the vehicle.
)
Put the gear lever into neutral (vehicles
fitted with a manual gearbox), or in
position P
(vehicles fitted with a CVT
gearbox).
)
While pressing the key, turn it to position 1
(LOCK)
.
)
Remove the key from the ignition switch.
)
Lock the steering.
Do not attach any heavy objects to the
key as this could weigh down on it when
in the ignition switch and cause a fault.
For Diesel vehicles, when the engine
is cold wait with the ignition switch
in position 3 (ON)
until the preheater
warning lamp goes off, before turning
the key to position 4 (START)
.
The warning lamp does not come on
when the engine is hot.
Switching off the engine leads to a loss
of braking assistance.
Page 112 of 368
110
Driving
For Diesel vehicles, when
the engine is cold starting
does not take place until the
pre-heater warning lamp has
gone off.
If one of the starting conditions is not
met, a reminder message appears in
the instrument panel screen. In some
circumstances, it is necessary to
turn the steering wheel slightly while
pressing the " START/STOP
" button
to assist unlocking of the steering;
a message warns you when this is
needed.
The presence of the electronic key
in the defined zone is essential. For
reasons of safety, do not leave this area
when the engine is running.
Switching off using the
electronic key
If the vehicle is not immobilised, the
engine will not stop.
This message is displayed
when the driver's door is
opened and the vehicle is not
in "OFF" mode.
)
Press the " START/STOP
" button again to
change to "OFF" mode.
)
Immobilise the vehicle.
)
Place the gear lever in neutral for vehicles
fitted with a manual gearbox , or on P
for
vehicles fitted with a CVT gearbox .
)
With the electronic key inside the vehicle,
press the " START/STOP
" button.
The engine stops.
The steering locks when a door is opened or on
locking the vehicle.
Each attempt at starting takes around
15 seconds. If the engine does not start, press
the " START/STOP
" button once more to try
again.
The presence of the electronic key in
the vehicle is essential for switching on
the ignition and starting only. Once the
engine has started, make sure that the
electronic key remains with the vehicle
until the end of the journey: other wise
you would not be able to lock the
vehicle.
Switching off the engine leads to a loss
of braking assistance.
