Page 185 of 368
183
7
Practical information
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block traffic: if possible, park the vehicle
on level, stable and non-slippery
ground.
Apply the parking brake, switch off the
ignition and engage first gear to lock
the wheels.
If necessary, place a chock under the
wheel diagonally opposite the wheel to
be changed.
Never go underneath a vehicle raised
using a jack; use a stand.
List of operations
)
If your vehicle is equipped with security
wheel bolts (equipment available as an
accessory) fit the security socket 5
on the
wheelbrace 1
to slacken the security bolt.
)
Slacken the other bolts using the
wheelbrace 1
only.
Page 186 of 368
184
Practical information
)
Place the jack 2
in contact with one of the
two front A
or rear B
locations provided on
the underbody, whichever is closest to the
wheel to be changed.
)
Extend the jack 2
until its base plate is in
contact with the ground. Ensure that the
centreline of the jack base plate is directly
below the location A
or B
used.
)
Raise the vehicle until there is sufficient
space between the wheel and the ground
to admit the spare (not punctured) wheel
easily.
)
Remove the bolts and store them in a
clean place.
)
Remove the wheel.
Page 187 of 368
185
7
Practical information
Fitting a wheel
After changing a wheel
When using the "space-saver" spare
wheel, do not exceed a speed of
50 mph (80 km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a PEUGEOT dealer or a qualified
workshop without delay.
Have the punctured wheel repaired and
replace it on the vehicle as soon as
possible.
List of operations
)
Put the wheel in place on the hub.
)
Screw in the bolts fully by hand.
)
Pre-tighten the security bolt using the
wheelbrace 1
fitted with the security
socket 5
(if your vehicle is equipped with
security wheel bolts).
)
Pre-tighten the other bolts using the
wheelbrace 1
only.
Fitting snow tyres
If you equip your vehicle with snow
tyres fitted on steel wheel rims, special
bolts available from your PEUGEOT
dealer or a qualified workshop must
be used.
If the replacement of a tyre is
necessary on 4-wheel drive versions,
it is recommended that all four tyres be
replaced at the same time, ensuring
that the same make, model and size is
used on all wheels.
This is because using tyres of different
sizes, structure or rate of wear could
damage transmission components.
Page 188 of 368
186
Practical information
)
Lower the vehicle fully.
)
Fold the jack 2
and detach it.
)
Tighten the security bolt using the
wheelbrace 1
fitted with the security
socket 5
(if your vehicle is equipped with
security wheel bolts).
)
Tighten the other bolts using the
wheelbrace 1
only.
)
Store the tools (refer to the paragraph
"Access to the tools").
Page 189 of 368
187
7
Practical information
For more information on snow chains,
contact a PEUGEOT dealer or a
qualified workshop.
Snow chains
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when
braking.
Advice on installation
)
If you have to fit the chains during a
journey, stop the vehicle on a flat sur face
on the side of the road.
)
Apply the parking brake and position any
wheel chocks to prevent movement of your
vehicle.
)
Fit the chains following the instructions
provided by the manufacturer.
)
Move off gently and drive for a few
moments, without exceeding 30 mph
(50 km/h).
)
Stop your vehicle and check that the snow
chains are correctly tightened.
The snow chains must be fitted only
to the front wheels. They must never
be fitted to "space-saver" type spare
wheels.
Take account of the legislation in force
in your country on the use of snow
chains and the maximum running speed
authorised.
Avoid driving on roads that have been
cleared of snow, to avoid damaging
your vehicle's tyres and the road
sur face. It is recommended that before
you leave, you practise fitting the snow
chains on a level and dry sur face. If
your vehicle is fitted with alloy wheels,
check that no part of the chain or its
fixings is in contact with the wheel rim.
Use only chains designed for fitment to the type
of road wheels on your vehicle:
Original equipment
tyre size Maximum link size
215/70 R16
12 mm
225/55 R18
Page 206 of 368
204
Practical information
Recovering the vehicle
Recover y of your vehicle
2 wheel drive (2WD) versions: towing
with the wheels on the ground
)
Put the gear lever into neutral (position N
for the CVT gearbox).
)
Unlock the steering by by turning the
ignition switch to the " ON
" position (or
to " ON
" mode for vehicle fitted with the
"Keyless Entry and Starting" system).
)
Release the parking brake.
)
Switch on the hazard warning lamps on
both vehicles.
)
Move off gently and travel slowly for a short
distance only.
General recommendations
Observe the legislation in force in your
country.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a vehicle with all four
wheels on the ground, always use an
approved towing bar; rope and straps
are prohibited.
When towing a vehicle with the engine
off, there is no longer any power
assistance for braking or steering.
In the following cases, you must always
call on a professional recovery ser vice:
- vehicle broken down on a motor way
or fast road,
- 4 wheel drive vehicle,
- when it is not possible to put the
gearbox into neutral, unlock the
steering, or release the parking
brake,
- towing with only two wheels on the
ground,
- where there is no approved towing
bar available...
Towing with the wheels on the ground
is only possible on 2 wheel drive (2WD)
versions.
)
Fit the towing bar to the towing eye on the
chassis, located under the front bumper.
Page 207 of 368
205
7
Practical information
Vehicles fitted with the 4 wheel drive
system must always be recovered on a
flatbed.
Never have the vehicle towed with the
four wheels on the ground, this could
damage the transmission.
The vehicle must not be towed with
the front or rear wheels on the ground
evenif it is in front "2WD" (2 wheel
drive) mode.
4 wheel drive (4WD) versions: recovery on a fl atbed
Page 208 of 368
206
Practical information
Towing another vehicle
)
On the rear bumper, remove the cover
by pulling at the bottom using the jack
handle 1
.
)
Screw in the towing eye 2
fully using the
wheelbrace 3
.
)
Install the towing bar.
)
Switch on the hazard warning lamps on
both vehicles.
)
Move off gently and travel slowly for a short
distance only.
Access to the tooling
The towing eye and the tools are stored under
the boot floor.
To gain access to them:
)
open the boot,
)
lift and remove the boot floor,
)
take the towing eye and the tools required.
List of tools
1.
Jack handle.
2.
To w i n g e y e .
3.
Wheelbrace.
