161
Changing a wheel
The tools are installed in the boot under the
f l o o r.
To gain access to them:
F
o
pen the boot,
F
l
ift the floor and remove it.
F
r
emove the carrier box containing the tools.
Access to the tools
List of tools*
3. "Bolt cover" tool. F or removing the bolt protectors (covers)
on alloy wheels.
4.
S
ocket for the security bolts (located in the
glove box).
F
or adapting the wheelbrace to the special
"security" bolts.
5.
T
owing eye.
S
ee "Towing the vehicle".
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
All of these tools are specific to your vehicle and
can vary according to the level of equipment. Do
not use them for other purposes.
1.
Wheelbrace.
F
or removing the wheel trim and removing
the wheel bolts.
2.
J
ack with integral handle.
F
or raising the vehicle. * Depending on country of sale.
7
Practical information
164
F Place the foot of the jack 2 on the ground and ensue that it is directly below the
front A or rear B location provided on the
underbody, whichever is closest to the
wheel to be changed.
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block traffic: the ground must be level,
stable and not slippery.
Apply the parking brake, switch off the
ignition and engage first gear* to block
the wheels.
Check that the parking brake warning
lamps in the instrument panel come on.
The occupants must get out of the
vehicle and wait where they are safe.
Never go underneath a vehicle raised
using a jack; use an axle stand.
List of operations
F Remove the bolt cover from each of the bolts using the tool 3 (according
to equipment).
F
F
it the security socket 4 on the
wheelbrace
1 to slacken the security bolt
(if
fitted).
F
S
lacken the other bolts using the
wheelbrace 1 o n l y.
*
P
os
ition R for an electronic gearbox; P for an
automatic gearbox.
Practical information
165
F Remove the bolts and store them in a clean place.
F
R
emove the wheel.
F
ex
tend the jack 2 until it comes into contact
with the location A or B used; the contact
sur face A or B on the vehicle must be
inserted into the central part of the head of
the jack.
F
Ra
ise the vehicle until there is sufficient
space between the wheel and the ground
to admit the spare (not punctured) wheel
easily.
en
sure that the jack is stable. If the
sur face is slippery or loose, the jack
may slip or drop - Risk of injury!
Take care to position the jack only at
the location A or B under the vehicle,
ensuring that the contact sur face on
the vehicle is well centred on the head
of the jack. Otherwise there is a risk of
damage to the vehicle and/or of the jack
dropping - Risk of injury!
7
Practical information
166
Fitting a wheel
Fitting the "space-saver"
spare wheel
If your vehicle is fitted with alloy wheels,
when tightening the bolts on fitting, it
is normal to notice that the washers
do not come into contact with the
"space-saver" spare wheel. The wheel
is secured by the conical sur face of
each bolt.
After changing a wheel
To store the punctured wheel in the
boot correctly, first remove the central
c ove r.
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80
km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a P
e
uge
O
T dealer or a qualified
workshop without delay.
Have the punctured wheel repaired
and refitted to the vehicle as soon as
possible.
List of operations
F Put the wheel in place on the hub.
F S crew in the bolts fully by hand.
F
P
re-tighten the security bolt using the
wheelbrace 1 fitted with the security
socket
4 (if your vehicle has them).
F
P
re-tighten the other bolts using the
wheelbrace 1 o n l y.
Practical information
193
Accessories
A wide range of accessories and genuine parts is available from the PeugeO T dealer network.
These accessories and parts are all adapted to your vehicle and benefit from Pe ugeO T's
recommendation and warranty.
Conversion kits
You can obtain an "en terprise" kit to convert a
trade vehicle to a private car and vice-versa.
"Comfort":
door deflectors, side blinds and rear blind,
cigarette lighter, boot dividers, coat hanger
fixed to head restraint, front centre armrest,
under shelf storage, front and rear parking
sensors...
"Transport solutions":
boot liner with dividers, luggage net, roof bars,
bicycle carrier on roof bars, ski carrier, roof
box....
*
T
o avoid any risk of jamming of the pedals:
-
e
nsure that the mat is positioned and
secured correctly,
-
n
ever fit one mat on top of another.
"Styling":
aluminium gear lever knob, spoiler, styling
strips, alloy wheels, trims, chromed mirror
shells, body kit, three personalisation lines
(Ligne S, Street and g
r
affic), stickers, interior
and exterior mirror shells, parking brake lever
grip, alloy wheels, alloy wheel caps...
"Security and safety":
anti-theft alarm, window engraving, wheel
security bolts, child seats and booster
cushions, breathalyzer, first aid kit, warning
triangle, high visibility jacket, stolen vehicle
tracking system, temporary puncture repair
kit, snow chains, non-slip covers, front
foglamps kit...
"Protection":
mats*, seat covers compatible with lateral
airbags, mud flaps, side rubbing strips, bumper
protective mouldings, aluminium or PVC door
aperture finishers...
Tow bar, which mst be fitted by
P
e
uge
O
T dealer or a qualified
workshop.
7
Practical information
