2014 Peugeot 207 CC ESP

!
!
i
6
FAMILIARISATION
207CC_EN_CHAP00B_PRISE EN MAIN_ED01-2014
OPENING
Retractable roof
When washing your vehicle:
- lock the vehicle,
- avoid spraying the upper part
of the windows,
- keep the end of the high-pres- sure nozzle at least 1 metre
from the windows and door
seals.
After washing the vehicle or fol-
lowing rain, wait until the roof has
dried before opening it.
The roof is operated under the
sole responsibility of the driver.
During operation of the roof, to
avoid the risk of injury, ensure that
no one is in the vicinity of the mov-
ing parts.
You are strongly advised not to op-
erate the roof in strong winds. It is preferable to operate the roof
with the engine running.
The roof can be operated at
speeds below 6 mph (10 km/h).
It is only possible to carry out the
operation twice with the engine off,
to avoid discharging the battery.
Preliminary conditions
 Switch on the ignition.
 Ensure that:
- the vehicle is not in energy econo-my mode (refer to the correspond-
ing section),
- the battery voltage is suffi cient indicator lamp on in the roof con-
trol),
- the roof fuse is in good condition (refer to the corresponding section),
- the electric windows are initialised (refer to the corresponding section),
- the ambient temperature is above -15 °C.
Precautions to be taken before
operating the roof
 Park the vehicle on level ground.
 Check that no object could hinder
the operation of the roof:
- nothing should be placed on the moving rear shelf 1 or on the
net 2 .
- if luggage is being carried in the boot, it must not raise the net,
 Ensure that the net 2 is secure.
 Close the boot correctly.
Maintenance
Carry out a complete opening
and closing operation of the roof
at least once a month to keep it in
good working order.

10
FAMILIARISATION
207CC_EN_CHAP00B_PRISE EN MAIN_ED01-2014
INSTRUMENTS AND CONTROLS
1. Steering lock and ignition.
2. Audio equipment steering mounted controls.
3. Wiper/wash-wipe/trip computer control stalk.
4. Hazard warning lamps switch.
5. Multifunction screen.
Seat belt fastening status warning lamps.
6. Sunshine sensor.
7. Passenger's airbag.
8. Glove box/Passenger's airbag deactivation/Audio/video sockets.
9. Heated seat control.
10. 12 V accessory socket.
11 . USB port.
12. Dynamic stability control (ESP/ASR) button.
Central locking button.
Alarm button.
13. Heating/air conditioning controls.
14. Storage compartment.
15. Audio and telematics system.
16. Central adjustable air vents.

15
FAMILIARISATION
207CC_EN_CHAP00B_PRISE EN MAIN_ED01-2014
MONITORING
Instrument panel Switch panel
A. With the ignition on, the fuel gauge nee-
dle should rise.
B. With the engine running, the associated
low level warning lamp should go off.
C. With the ignition on, the oil level in-
dicator should display "OIL OK" for
a few seconds.
If the levels are not correct, top up the level
which is low.
Ilumination of the indicator lamp gives
the status of the corresponding function.
A. Deactivation of the ESP/ASR system.
1. With the ignition on, the orange and
red warning lamps come on.
2. With the engine running, these warning lamps should go off.
If a warning lamp remains on, refer to
the page concerned.
Warning lamps
B. Central locking.
C. Deactivation of the interior volumetric protection alarm.
 20  21 101
 74
 69

1
i
MONITORING
20
207CC_EN_CHAP01_CONTROLE DE MARCHE_ED01-2014
PETROL - DIESEL, MANUAL OR AUTOMATIC GEARBOX,
INSTRUMENT PANELS
Panel which groups together the vehicle operation dials and indicator la\
mps. 5. Screen.
6. Display zero reset button.
Resets the selected function to zero (trip distance recorder or service in-
dicator).
7. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
8. Automatic gearbox.
Indicates the programme selected and the gear engaged.
Dials
1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
2. Fuel gauge.
Indicates the quantity of fuel remain- ing in the tank.
3. Coolant temperature.
Indicates the temperature of the en- gine coolant (°Celsius).
4. Speedometer.
Indicates the current speed of the moving vehicle (mph or km/h). A. Speed limiter
or

Cruise control.
(mph or km/h)
B. Trip distance recorder.
(miles or km/h)
C. Service indicator.
(miles or km/h) then,
Engine oil level indicator.
then
Distance recorder.
km or miles)
These three functions are displayed in succession when the ignition is
switched on.
Screen
For more information, refer to the
corresponding section for the func-
tion and to the display associated
with it.

1
!
MONITORING
21
207CC_EN_CHAP01_CONTROLE DE MARCHE_ED01-2014
INDICATOR AND WARNING LAMPS
Visual indicators informing the driver that a system is in operation (op\
eration or
deactivation indicator lamps) or of the occurrence of a fault (warning\
lamp).
When the ignition is switched on
Certain warning lamps come on for a few seconds when the vehicle's ignit\
ion is switched
on.
When the engine is started, these same warning lamps should go off.
If they remain on, before moving off, refer to the information on the warning lamp concerned.
The warning lamps may come on
continuously (fi xed) or fl ash.
Certain warning lamps may come
on in one of two different modes.
Only by relating the type of illumi-
nation to the operating status of
the vehicle can it be ascertained
whether the situation is normal or
whether a fault has occurred.
Associated warnings
The illumination of certain warning lamps may be accompanied by an audible s ignal
and a message in the multifunction screen.
Warning lamp is on Cause Action/Observations
Left-hand direction
indicato r fl ashing with
buzzer. The lighting stalk is pushed
down.
Right-hand direction
indicator fl ashing with
buzzer. The lighting stalk is pushed
up.
Dipped beam headlamps fi xed. The lighting stalk is in the
"Dipped beam headlamps"
position.
Main beam
headlamps fi xed. The lighting stalk is pulled
towards you. Pull the stalk to return to dipped beam
headlamps.
Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the correspond-
ing system has come into operation.

1MONITORING
23
207CC_EN_CHAP01_CONTROLE DE MARCHE_ED01-2014
Deactivation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the corresponding system has been switched off intentionally.
This is may be accompanied by an audible signal and a message on the mul\
tifunction screen. Warning lamp is on Cause Action/Observations
Passenger's
airbag
system fi xed. The control, located in the
glove box, is set to the
OFF position.
The passenger's front
airbag is deactivated.
You can install a "rearward
facing" child seat, unless
there is a fault with the
operation of the airbags
(Airbag warning lamp on). Set the control to the
ON position to activate the
passenger's front airbag.
In this case, do not fi t a child seat in the rearward
facing position.
ESP/ASR fi xed. The button, located
in the centre of
the dashboard,
is pressed. Its
indicator lamp is on.
The ESP/ASR is
deactivated.
ESP: electronic stability
programme.
ASR: anti-slip regulation. Press the button again to reactivate the ESP/
ASR manually. Its indicator lamp goes off.
From approximately 30 mph (50 km/h), the
system is reactivated automatically.
The ESP/ASR system is reactivated
automatically when the vehicle is started.

1MONITORING
25
207CC_EN_CHAP01_CONTROLE DE MARCHE_ED01-2014
Warning lamp is on Cause Action/Observations
Anti-lock Braking System (ABS) fi xed.
The anti-lock braking
system has a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact
a PEUGEOT dealer or a qualifi ed workshop
without delay.
Electronic
stability

programme

( ESP /ASR) fl ashing.
The ESPASR regulation is
operating. The system optimises traction and improves the
directional stability of the vehicle.
fi xed. Unless it has been
deactivated (button pressed
and its indicator lamp on) the
ESP/ASR system has a fault. Have it checked by a PEUGEOT or a qualifi ed
workshop.
Engine
autodiagnosis system fl ashing.
The engine management
system has a fault. Risk of destruction of the catalytic converter.
Have it checked by a PEUGEOT dealer or a
qualifi ed workshop.
fi xed. The emission control
system has a fault. The warning lamp should go off when the engine
is started.
If it does not go off, contact a PEUGEOT dealer
or qualifi ed workshop without delay.
Low fuel level fi xed. When it fi rst comes on there
remains
approximately
5 litres of fuel in the tank. You must refuel as soon as possible to avoid
running out of fuel.
This warning lamp will come on every time
the ignition is switched on, until a suffi cient
addition of fuel is made.
Fuel tank capacity: approximately 50 litres
(petrol) or 48 litres (Diesel).
Never continue to drive until you run out of fuel
as this could damage the emission control and
injection systems.

1
!
MONITORING
34
207CC_EN_CHAP01_CONTROLE DE MARCHE_ED01-2014
Vehicle confi guration
Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not ac-
tive, faulty). Language
Once the "Language" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:
- temperature (°C or °F),
- fuel consumption (l/100 km, mpg or
km/l).
 Once you have selected a setting, press the "OK" button to change its
value.
 Wait for approximately ten sec- onds without any action to allow
the changed data to be recorded or
press the "Back" button to cancel.
The screen then returns to the normal
display.
Once the "Vehicle confi guration" menu
has been selected, you can activate or
deactivate the following equipment:
- directional headlamps (refer to the
"Visibility" section),
- "guide-me-home" lighting (refer to the "Visibility" section),
For safety reasons, confi guration
of the multifunction screen by the
driver must only be done when sta-
tionary.