2014 PEUGEOT 2008 Owners Manual

167
7
Practical information
Changing main beam headlamp bulbs Changing the daytime running lamps / sidelamps (light- emitting diodes - LEDs)
For the replacement of this type of LED lamp, contact a PEUGEOT dealer or a qualified workshop.
To reassemble, carry out these operations in reverse order, positioning the alignment lug at the bottom.
 Remove the protective cover by pulling on the tab.  Disconnect the bulb connector.  Pull out the bulb and replace it.

168
Practical information
Changing front foglamp / directional lamps
 Access to the front foglamp is through the orifice below the bumper.  Disconnect the bulb holder connector by pressing on the top of the tongue.  Extract the bulb holder by pressing on the two clips clips (top and bottom).  Replace the module. To reassemble, carry out these operations in reverse order.
Changing integrated direction indicator side repeater bulbs
 Press the central tongue and remove the side repeater.  Pull the bulb holder out and replace the failed bulb. To reassemble, carry out these operations in reverse order. You should contact a PEUGEOT dealer or a qualified workshop for the replacement of these bulbs.
 Insert a flat screwdriver between the mirror glass and its base.  Use the screwdriver as a lever to extract the mirror glass.  Unclip the mirror shell by pressing on the two retaining clips.
To obtain this module, contact a
PEUGEOT dealer or a qualified workshop. You can also contact a PEUGEOT dealer or a qualified workshop for this replacement.

169
7
Practical information
1. Brake lamps (P21W).2. Sidelamps (light emitting diodes - LEDs).3. Direction indicators (PY21W amber).
Rear lamps
Changing the light emitting diode-LED lamps
For replacement, contact a PEUGEOT dealer or qualified workshop.
4. Foglamp (P21W).5. Reversing lamp (P21W).

170
Practical information
Changing brake lamp and direction indicator bulbs
These bulbs are changed from inside the boot:
 open the boot,  remove the access grille from the corresponding side trim panel,  slacken and remove the nut,  disconnect the lamp unit connector,  remove the lamp unit carefully by it pulling in line towards the outside,
 press the retaining tabs and remove the bulb holder,  turn the bulb a quarter of a turn and change it. To reassemble, carry out these operations in reverse order. Take care to engage the lamp unit in its guides, while keeping it in line with the vehicle. Tighten sufficiently to ensure sealing, but without damaging the lamp.

171
7
Practical information
Changing the third brake lamp (light emitting diodes - LEDs)
Contact a PEUGEOT dealer or a qualified workshop.
Number plate lamps
To facilitate the removal of the lamp, carry out this operation with the tailgate half open.
 Insert a thin screwdriver into the lens cutout.  Push it outwards.  Remove the lens.  Change the faulty bulb. To refit, press on the lens to clip it in place.
Access is by passing a hand under the bumper.  Turn the bulb holder an eighth of a turn and pull it out.  Change the failed bulb. To refit, carry out these operations in reverse o r d e r.
Changing a foglamp or reversing lamp bulb
On the left hand side, take care to not touch the exhaust silencer; risk of burns if changing a bulb after stopping the engine.

172
Practical information
Changing a fuse
The extraction tweezer is fitted to the back of the dashboard fusebox cover.  unclip the cover by pulling at the top left, then right,  disengage the cover completely and turn it over,
Access to the tools
 remove the carrier on which the tweezer is fitted.

173
7
Practical information
To replace a fuse, you must:  use the special tweezer to extract the fuse from its housing and check the condition of its filament,  always replace the failed fuse with a fuse of the same rating (same colour); using a different rating could cause faults (risk of f i r e). If the fuse fails again soon after replacement, have the vehicle's electrical system checked by a PEUGEOT dealer or a qualified workshop.
Changing a fuse
Before changing a fuse:  the cause of the failure must be identified and rectified,  all electrical consumers must be switched of f,  the vehicle must be immobilised with the ignition off,  identify the failed fuse using the tables and layout drawings in the following pages. GoodFailed
PEUGEOT will not accept responsibility for the cost incurred in repairing your vehicle or for rectifying malfunctions resulting from the installation of accessories not supplied and not
recommended by PEUGEOT and not installed in accordance with its instructions, in particular when the combined consumption of all of the additional equipment connected exceeds 10 milliamperes.
Installing electrical accessories
Your vehicle's electrical system is designed to operate with standard or optional equipment. Before installing other electrical equipment or accessories on your vehicle, contact a PEUGEOT dealer or a qualified workshop.
The replacement of a fuse not shown in the tables below may cause a serious malfunction of your vehicle. Contact a PEUGEOT dealer or a qualified workshop.
Tw e e z e r

174
Practical information
Dashboard fuses
The fusebox is placed in the lower dashboard (left-hand side).
Access to the fuses
 Refer to the paragraph "Access to the to o ls".
Fuse N°RatingFunctions
F25 A Door mirrors, headlamps, diagnostic socket.
F95 A Alarm.
F105 A Independent telematic unit, trailer interface.
F115 A Electrochrome rear view mirror, additional heating.
F135 A Hi-Fi amplifier, parking sensors
F1615 A Front 12 V socket.
F1715 A Audio system, audio system (accessory).
F1820 A Touch screen.
Fuse tables