2014 NISSAN TEANA crank

DIAGNOSIS SYSTEM (ECM)EC-603
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
×
: Applicable
Monitored item Unit Monitor Item Selec-
tion
Description Remarks
ECU IN-
PUT SIG- NALS MAIN-
SIG-
NALS
ENG SPEED rpm ××Indicates the engine speed comput-
ed from the signal of the crankshaft
position sensor (POS) and camshaft
position sensor (PHASE). • Accuracy becomes poor if engine
speed drops below the idle rpm.
• If the signal is interrupted while the engine is running, an abnor-
mal value may be indicated.
MAS A/F SE-B1 V ××The signal voltage of the mass air
flow sensor is displayed. • When the engine is stopped, a
certain value is indicated.
• When engine is running, specifi- cation range is indicated in
“SPEC”.
B/FUEL SCHDL ms ×דBase fuel schedule” indicates the
fuel injection pulse width pro-
grammed into ECM, prior to any
learned on board correction. • When engine is running, specifi-
cation range is indicated in
“SPEC”.
A/F ALPHA-B1
% The mean value of the air-fuel ratio
feedback correction factor per cycle
is indicated. • When the engine is stopped, a
certain value is indicated.
• This data also includes the data
for the air-fuel ratio learning con-
trol.
• When engine is running, specifi-
cation range is indicated in
“SPEC”.
A/F ALPHA-B2
COOLAN TEMP/S °C or °F ×× The engine coolant temperature (de-
termined by the signal voltage of the
engine coolant temperature sensor)
is displayed. When the engine coolant tempera-
ture sensor is open or short-circuit-
ed, ECM enters fail-safe mode. The
engine coolant temperature deter-
mined by the ECM is displayed.
A/F SEN1 (B1) V××
The A/F signal computed from the
input signal of the air fuel ratio (A/F)
sensor 1 is displayed.
A/F SEN1 (B2)
××
HO2S2 (B1) V××
The signal voltage of the heated ox-
ygen sensor 2 is displayed.
HO2S2 (B2) ××
HO2S2 MNTR(B1)
RICH/LEAN ×
Display of heated oxygen sensor 2
signal:
• RICH: means the amount of oxy-
gen after three way catalyst is rel-
atively small.
• LEAN: means the amount of oxy-
gen after three way catalyst is rel-
atively large. When the engine is stopped, a cer-
tain value is indicated.
HO2S2 MNTR(B2) ×
VHCL SPEED SE km/h or
mph ×× The vehicle speed computed from
the vehicle speed signal sent from
combination meter is displayed.
BATTERY VOLT V The power supply voltage of ECM is
displayed.
ACCEL SEN 1 V The accelerator pedal position sen-
sor signal voltage is displayed. ACCEL SEN 2 signal is converted
by ECM internally. Thus, it differs
from ECM terminal voltage signal.
ACCEL SEN 2
TP SEN 1-B1 V××
The throttle position sensor signal
voltage is displayed. TP SEN 2-B1 signal is converted by
ECM internally. Thus, it differs from
ECM terminal voltage signal.
TP SEN 2-B1
××
FUEL T/TMP SE °C or °F The fuel temperature (determined by
the signal voltage of the fuel tank
temperature sensor) is displayed.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-610
< SYSTEM DESCRIPTION >[VQ35DE]
DIAGNOSIS SYSTEM (ECM)
*: This function is not necessary in the usual service procedure.
ACTIVE TEST MODE
Test Item
WORK ITEM CONDITION USAGE
IDLE AIR VOL LEARN The idle air volume that keeps the engine within the specified range is memorized in ecm. When learning the idle air volume
EVAP SYSTEM CLOSE Close the EVAP canister vent control valve in order to make
EVAP system close under the following conditions.
• Ignition switch ON
• Engine not running
• Ambient temperature is above 0 °C (32 °F).
• No vacuum and no high pressure in EVAP system
• Fuel tank temperature is more than 0 °C (32 °F).
• Within 10 minutes after starting “EVAP SYSTEM CLOSE”
• When trying to execute “EVAP SYSTEM CLOSE” under
the condition except above, CONSULT will discontinue it
and display appropriate instruction.
NOTE:
When starting engine, CONSULT may display “BAT-
TERY VOLTAGE IS LOW. CHARGE BATTERY”, even in
using charged battery. When detecting EVAP vapor leak-
age in the EVAP system
FUEL PRESSURE RELEASE Fuel pu mp will stop by touching “START” during idling.
crank a few times after engine stalls. When releasing fuel pressure from
fuel line
SELF-LEARNING CONT The coefficient of self-learning control mixture ratio returns to the original coefficient. When clearing mixture ratio self-
learning value
TARGET IGN TIM ADJ* Idle condition When adjusting target ignition tim- ing
TARGET IDLE RPM ADJ* Idle condition When setting target idle speed
VIN REGISTRATION In this mode, VIN is registered in ECM When registering VIN in ECM
CLSD THL POS LEARN Ignition on and engine stopped. When learning the throttle valve
closed position
SAVING DATA FOR REPLC CPU In this mode, save data that is in ECM. When ECM replaced.
WRITING DATA FOR REPLC CPU In this mode, write data stored by “SAVING DATA FOR RE-
PLC CPU” in work support mode to ECM. When ECM replaced.
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
FUEL INJEC-
TION • Engine: Return to the original
non-standard condition
• Change the amount of fuel injec- tion using CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. • Harness and connectors
• Fuel injector
• Air fuel ratio (A/F) sensor 1
ENG COOLANT
TEMP • Engine: Return to the original
non-standard condition
• Change the engine coolant tem- perature using CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. • Harness and connectors
• Engine coolant temperature sen-
sor
• Fuel injector
PURG VOL
CONT/V • Engine: After warming up, run en-
gine at 1,500 rpm.
• Change the EVAP canister purge volume control solenoid valve
opening percent using CON-
SULT. Engine speed changes according to
the opening percent. • Harness and connectors
• Solenoid valve
FUEL/T TEMP
SEN • Change the fuel tank temperature using CONSULT.
ALTERNATOR
DUTY •Engine: Idle
• Change duty ratio using CON-
SULT. Battery voltage changes.
• Harness and connectors
• IPDM E/R
•Alternator
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-615
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
INT/V TIM (B1)
• Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
INT/V TIM (B2) • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
INT/V SOL(B1) • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 0 - 2%
2,000 rpm Approx. 0 - 50%
INT/V SOL(B2) • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 0 - 2%
2,000 rpm Approx. 0 - 50%
VIAS S/V-1 • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load When revving engine up to 5,000 rpm
quickly Off
→On → Off
VIAS S/V-2 • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load When revving engine up to 5,000 rpm
quickly Off
→On → Off
AIR COND RLY Engine: After warming up, idle the
engine Air conditioner switch: OFF Off
Air conditioner switch: ON
(Compressor operates) On
ENGINE MOUNT Engine: After warming up Below 950 rpm IDLE
Above 950 rpm TRVL
FUEL PUMP RLY • For 1 second after turning ignition switch: ON
• Engine running or cranking On
Except above Off
VENT CONT/V Ignition switch: ON Off
THRTL RELAY Ignition switch: ON On
A/F S1 HTR(B1) Engine: After warming up, idle the engine
(More than 140 seconds after starting engine) 4 - 100%
A/F S1 HTR(B2) Engine: After warming up, idle the engine
(More than 140 seconds after starting engine) 4 - 100%
COOLING FAN • Engine: After warming up, idle the
engine
• Air conditioner switch: OFF Engine coolant temperature: 97
°C
(206 °F) or less OFF
Engine coolant temperature: Between
98 °C (208
°F) and 99 °C (210 °F) LOW
Engine coolant temperature: Between
100 °C (212 °F) and 104 °C (219 °F) MID
Engine coolant temperature: 105 °C
(221 °F) or more HI
HO2S2 HTR (B1) Engine speed: Below 3,600 rpm after the following conditions are met.
• Engine: After warming up
• Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load On
Engine speed: Above 3,600 rpm Off
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-622
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
41
(LG) 128
(GR) Heated oxygen sensor 2 heat-
er (bank 2) Output[Engine is running]
Engine speed: Below 3,600 rpm
after the following conditions are
met
• Engine: after warming up
• Keeping the engine speed be- tween 3,500 and 4,000 rpm
for 1 minute and at idle for 1
minute under no load 10 V
• [Ignition switch: ON] Engine stopped
• [Engine is running] Engine speed: Above 3,600
rpm BATTERY VOLTAGE
(11 - 14 V)
42
(BR) 128
(GR) EVAP canister purge volume
control solenoid valve Output[Engine is running]
• Idle speed
• Accelerator pedal: Not de- pressed even slightly, after
engine starting BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
Engine speed: approximately
2,000 rpm (More than 100 sec-
onds after starting engine) BATTERY VOLTAGE
(11 - 14 V)
43
(V) 128
(GR) Fuel pump relay Output • [Ignition switch: ON]
For 1 second after turning ig-
nition switch ON
• [Engine is running] 0 - 1.0 V
54
(V) 84
(SB) Sensor power supply
[Crankshaft position sensor
(POS)] — [Ignition switch: ON] 5 V
55
(Y) 128
(GR) Intake valve timing control so-
lenoid valve (bank 1) Output[Engine is running]
• Warm-up condition
• Idle speed BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 7 - 12 V
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
JMBIA0902GB
JMBIA0039GB
JMBIA0040GB
JMBIA0038GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-624
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
74
(V) 80
(BR) Intake air temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with intake air temperature.
75
(O) 68
(R) Sensor power supply
(Battery current sensor) — [Ignition switch: ON] 5 V
76
(B) —Sensor ground
(Engine coolant temperature
sensor, engine oil tempera-
ture sensor) —— —
77
(W) 128
(GR) A/F sensor 1 (bank 2) Input [Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 2.2 V
Output voltage varies with air fuel ratio.
78
(G) 76
(B) Engine oil temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
oil temperature.
80
(BR) —Sensor ground
(Mass air flow sensor, intake
air temperature sensor) —— —
81
(B) 128
(GR) A/F sensor 1 (bank 2) Input [Ignition switch: ON] 1.8 V
82
(P) 80
(BR) Mass air flow sensor Input [Engine is running]
• Warm-up condition
• Idle speed 0.9 - 1.2 V
[Engine is running]
• Warm-up condition
• Engine speed: 2,500 rpm 1.6 - 1.9 V
83
(V) 88
(SB) Sensor power supply
[Camshaft position sensor
(PHASE) (bank 1)] — [Ignition switch: ON] 5 V
84
(SB) —Sensor ground
[Crankshaft position sensor
(POS)] —— —
85
(B) 91
(B) Knock sensor (bank 1) Input [Engine is running]
Idle speed 2.5 V*
1
86
(W) 91
(B) Knock sensor (bank 2) Input [Engine is running]
Idle speed 2.5 V*1
87
(V) 92
(SB) Sensor power supply
[Camshaft position sensor
(PHASE) (bank 2)] — [Ignition switch: ON] 5 V
88
(SB) —Sensor ground
[Camshaft position sensor
(PHASE) (bank 1)] —— —
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-625
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
89
(LG) 84
(SB) Crankshaft position sensor
(POS) Input[Engine is running]
• Warm-up condition
• Idle speed NOTE:
The pulse cycle changes de-
pending on rpm at idle 4.0 - 5.0 V
[Engine is running]
Engine speed: 2,000 rpm 4.0 - 5.0 V
91
(B) —Sensor ground
[Knock sensor (bank 1),
knock sensor (bank 2)] —— —
92
(SB) —Sensor ground
[Camshaft position sensor
(PHASE) (bank 2)] —— —
93
(LG) 92
(SB) Camshaft position sensor
(PHASE) (bank 2) Input[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle 3.0 - 5.0 V
[Engine is running]
Engine speed is 2,000 rpm 3.0 - 5.0 V
94
(LG) 88
(SB) Camshaft position sensor
(PHASE) (bank 1) Input[Engine is running]
• Warm-up condition
• Idle speed NOTE:
The pulse cycle changes de-
pending on rpm at idle 3.0 - 5.0 V
[Engine is running]
Engine speed is 2,000 rpm 3.0 - 5.0 V
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
OutputJMBIA0041GB
JMBIA0042GB
JMBIA0045GB
JMBIA0046GB
JMBIA0045GB
JMBIA0046GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-629
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
DTC Inspection Priority ChartINFOID:0000000009462544
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
P2100
P2103 Throttle control motor relay ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2101 Electric th rottle control
function ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2118 Throttle control motor ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
P2119 Electric thro ttle control ac-
tuator (When electric throttle control actuator does not function properly due to the return spring
malfunction:)
ECM controls the electric throttle actuator by regulating the throttle opening around the
idle position. The engine speed will not rise more than 2,000 rpm.
(When throttle valve opening angle in fail-safe mode is not in specified range:)
ECM controls the electric throttle control actuator by regulating the throttle opening to 20
degrees or less.
(When ECM detects the throttle valve is stuck open:)
While the vehicle is being driven, it slows down gradually because of fuel cut. After the
vehicle stops, the engine stalls.
The engine can restart in the N or P position, and engine speed will not exceed 1,000 rpm
or more.
P2122
P2123
P2127
P2128
P2138 Accelerator pedal position
sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
DTC No. Detected items Engine operating condition in fail-safe mode
Priority Detected items (DTC) Detected items (DTC)
1 U0101, U1001 CAN communication line P0101, P0102, P0103 Mass air flow sensor
P0111, P0112, P0113, P0127 Intake air temperature sensor
P0116, P0117, P0118, P0125 Engine coolant temperature sensor
P0122, P0123, P0222, P0223, P1225, P1226, P2135 Throttle position sensor
P0128 Thermostat function
P0181, P0182, P0183 Fuel tank temperature sensor
P0196, P0197, P0198 Engine oil temperature sensor
P0327, P0328, P0332, P0333 Knock sensor
P0335 Crankshaft position sensor (POS)
P0340, P0345 Camshaft position sensor (PHASE)
P0460, P0461, P0462, P0463 Fuel level sensor
P0500 Vehicle speed sensor
P0520 EOP sensor
P0605, P0607 ECM
P0643 Sensor power supply
P0850 Transmission range switch
P1550, P1551, P1552, P1553, P1554 Battery current sensor
P1556, P1557 Battery temperature sensor
P1610 - P1615 NATS
P2122, P2123, P2127, P2128, P2138 Accelerator pedal position sensor
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-676
< BASIC INSPECTION >[VQ35DE]
BASIC INSPECTION
2. Rev engine (2,000 to 3,000 rpm) 2 or 3 times under no load,
then run engine at idle speed for approximately 1 minute.
3. Check idle speed.
For procedure, refer to EC-992, "Work Procedure"
.
For specification, refer to EC-998, "Idle Speed"
.
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 4.
4.PERFORM ACCELERATOR PEDAL RE LEASED POSITION LEARNING
1. Stop engine.
2. Perform EC-681, "Work Procedure"
.
>> GO TO 5.
5.PERFORM THROTTLE VALVE CL OSED POSITION LEARNING
Perform EC-682, "Work Procedure"
.
>> GO TO 6.
6.PERFORM IDLE AIR VOLUME LEARNING
Perform EC-683, "Work Procedure"
.
Is Idle Air Volume Learning carried out successfully?
YES >> GO TO 7.
NO >> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
7.CHECK IDLE SPEED AGAIN
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.
For procedure, refer to EC-992, "Work Procedure"
.
For specification, refer to EC-998, "Idle Speed"
.
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 8.
8.DETECT MALFUNCTIONING PART
Check the Following.
• Check camshaft position sensor (PHASE) and circuit. Refer to EC-820, "Diagnosis Procedure"
.
• Check crankshaft position sensor (POS) and circuit. Refer to EC-817, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace malfunctioning part. Then GO TO 4.
9.CHECK ECM FUNCTION
1. Substitute with a non-malfunctioning ECM to check EC M function. (ECM may be the cause of the incident,
although this is rare.)
2. Perform initialization of NVIS (NAT S) system and registration of all NVIS (NATS) ignition key IDs. Refer to
SEC-66, "ECM : Work Procedure"
.
>> GO TO 4.
10.CHECK IGNITION TIMING
1. Run engine at idle.
2. Check ignition timing with a timing light.
For procedure, refer to EC-993, "Work Procedure"
.
PBIA8513J
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM