2014 NISSAN TEANA fuel

EC-86
< SYSTEM DESCRIPTION >[QR25DE]
DIAGNOSIS SYSTEM (ECM)
*: Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.
DTC WORK SUPPORT MODE
DTC WORK SUPPORT Mode
ALTERNATOR
DUTY • Engine: Idle
• Change duty ratio using CON-
SULT. Battery voltage changes.
• Harness and connectors
•IPDM E/R
•Alternator
FUEL PUMP RELAY • Ignition switch: ON (Engine
stopped)
• Turn the fuel pump relay “ON”
and “OFF” using CONSULT and
listen to operating sound. Fuel pump relay makes the operat-
ing sound. • Harness and connectors
• Fuel pump relay
VIAS S/V-1 • Ignition switch: ON
• Turn intake manifold tuning valve
“ON” and “OFF” using CONSULT
and listen to operating sound. Intake manifold tuning valve motor
makes an operating sound. • Harness and connectors
• Intake manifold tuning valve mo- tor
TUMBLE CONTROL
VA LV E • Ignition switch: ON
• Turn intake manifold runner con-
trol valve “ON” and “OFF” using
CONSULT and listen to operating
sound. Intake Manifold Runner control
valve motor makes an operating
sound. • Harness and connectors
• Intake Manifold Runner control valve motor
IGNITION TIMING • Engine: Return to the original
trouble condition
• Timing light: Set
• Retard the ignition timing using
CONSULT. If trouble symptom disappears, see
CHECK ITEM. • Perform Idle Air Volume Learn-
ing.
POWER BALANCE • Engine: After warming up, idle the
engine.
• A/C switch OFF
• Selector lever: P or N
• Cut off each fuel injector signal one at a time using CONSULT. Engine runs rough or stops. • Harness and connectors
• Compression
• Fuel injector
• Power transistor
• Spark plug
• Ignition coil
VENT CONTROL/V • Ignition switch: ON (Engine
stopped)
• Turn solenoid valve “ON” and “OFF” using CONSULT and listen
to operating sound. Solenoid valve makes an operating
sound. • Harness and connectors
• Solenoid valve
INT V/T ASSIGN AN-
GLE • Engine: Return to the original
trouble condition
• Change intake valve timing using
CONSULT. If trouble symptom disappears, see
CHECK ITEM. • Harness and connectors
• Intake valve timing control sole- noid valve
EXH V/T ASSIGN
ANGLE • Engine: Return to the original
trouble condition
• Change exhaust valve timing us- ing CONSULT. If trouble symptom disappears, see
CHECK ITEM. • Harness and connectors
• Exhaust valve timing control so-
lenoid valve
COOLING FAN* • Ignition switch: ON
• Turn the cooling fan “LOW”, “HI” and “OFF” using CONSULT. Cooling fan moves and stops. • Harness and connectors
• IPDM E/R (Cooling fan relay)
• Cooling fan motor
Test item Condition Judgment Check item (Remedy)
Test mode Test item Corresponding DTC No. Reference page
EVAPORATIVE SYSTEM PURG FLOW P0441 P0441
EC-337
PURG VOL CN/V P1444 P0443EC-342
A/F SEN1 A/F SEN1(B1) P1276 P0130 EC-258
HO2S2HO2S2(B1) P1146 P0138
EC-274HO2S2(B1) P1147 P0137EC-268
HO2S2(B1) P0139 P0139EC-282
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-88
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
ECU DIAGNOSIS INFORMATION
ECM
Reference ValueINFOID:0000000009462121
VALUES ON THE DIAGNOSIS TOOL
NOTE:
• The following table includes information (items) inapplicable to this vehicle. For information (items) applica- ble to this vehicle, refer to CONSULT display items.
• Numerical values in the following table are reference values.
• These values are input/output values that ECM receiv es/transmits and may differ from actual operations.
Example: The ignition timing shown by the timing light may differ from the ignition timing displayed on the
data monitor.
This occurs because the timing light shows a value calculated by ECM according to signals received from
the camshaft position sensor and other sensors related to ignition timing.
• For outlines of following items, refer to EC-77, "CONSULT Function"
.
Monitor Item Condition Values/Status
ENG SPEED • Run engine and compare CONSULT value with the tachometer indication.Almost the same speed as
the tachometer indication.
MAS A/F SE-B1 See EC-196, "Diagnosis Procedure"
.
B/FUEL SCHDL See EC-196, "Diagnosis Procedure"
.
A/F ALPHA-B1 See EC-196, "Diagnosis Procedure"
.
COOLAN TEMP/S • Engine: After warming up More than 70 °C (158 °F)
A/F SEN1 (B1) • Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 2.2 V
HO2S2 (B1) • Revving engine from idle up to 3,000 rpm quickly after the following conditions
are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
←→ Approx. 0.6 -
1.0 V
HO2S2 MNTR(B1) • Revving engine from idle up to 3,000 rpm quickly after the following conditions
are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load LEAN
←→ RICH
VHCL SPEED SE • Turn drive wheels and compare CONSULT value with the speedometer indi-
cation. Almost the same speed as
speedometer indication
BATTERY VOLT • Ignition switch: ON (Engine stopped) 11 - 14 V
ACCEL SEN 1 • Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released 0.5 - 1.0 V
Accelerator pedal: Fully depressed 4.2 - 4.8 V
ACCEL SEN 2*
1• Ignition switch: ON (Engine stopped) Accelerator pedal: Fully released 0.5 - 1.0 V
Accelerator pedal: Fully depressed 4.2 - 4.8 V
TP SEN 1-B1 • Ignition switch: ON
(Engine stopped)
• Selector lever: D Accelerator pedal: Fully re
leased More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
TP SEN 2-B1*
1• Ignition switch: ON (Engine stopped)
• Selector lever: D Accelerator pedal: Fully released Less than 4.75 V
Accelerator pedal: Fully depressed More than 0.36 V
FUEL T/TMP SE • Ignition switch: ON Indicates fuel tank tempera-
ture
EVAP SYS PRES • Ignition switch: ON Approx. 1.8 - 4.8 V
FUEL LEVEL SE • Ignition switch: ON Depending on fuel level of
fuel tank
START SIGNAL • Ignition switch: ON → START → ON Off → On → Off
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-90
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
VIAS S/V-1• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load When revving engine up to 5,000 rpm
quickly Off
→ On → Off
AIR COND RLY • Engine: After warming up, idle the
engine Air conditioner switch: OFF Off
Air conditioner switch: ON
(Compressor operates) On
FUEL PUMP RLY • For 1 second after turning ignition switch: ON
• Engine running or cranking On
• Except above Off
VENT CONT/V • Ignition switch: ON Off
THRTL RELAY • Ignition switch: ON On
COOLING FAN • Engine: After warming up, idle the
engine
• Air conditioner switch: OFF Engine coolant temperature is 97
°C
(207 °F) or less Off
Engine coolant temperature between
98 °C (208 °F) and 99 °C (210 °F) or more Low
Engine coolant temperature between
100 °C (212 °F) or more Hi
• Engine: After warming up, idle the engine
• Air conditioner switch: ON
• Refrigerant pressure is less than 1,280 kPa (12.80 bar, 13.05 kg/
cm
2, 185.6 psi) Engine coolant temperature is 97
°C
(207 °F) or less Off
Engine coolant temperature between
98 °C (208 °F) and 99 °C (210 °F) or more Mid
Engine coolant temperature between
100 °C (212 °F) or more Hi
HO2S2 HTR (B1) • Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load On
• Engine speed: Above 3,600 rpm Off
ALT DUTY SIG • Power generation voltage variable control: Operating On
• Power generation voltage variable control: Not operating Off
I/P PULLY SPD • Vehicle speed: More than 20 km/h (12 MPH) Almost the same speed as
the tachometer indication
VEHICLE SPEED • Turn drive wheels and compare CONSULT value with the speedometer indi-
cation. Almost the same speed as
the speedometer indication
IDL A/V LEARN • Engine: running Idle air volume learning has not been per-
formed yet. YET
Idle air volume learning has already been
performed successfully. CMPLT
TRVL AFTER MIL • Ignition switch: ON Vehicle has traveled after MIL has turned
ON. 0 - 65,535 km
(0 - 40,723 miles)
ENG OIL TEMP • Engine: After warming up More than 70 °C (158 °F)
A/F S1 HTR(B1) • Engine: After warming up, idle the engine
(More than 140 seconds after starting engine.) 4 - 100%
VHCL SPEED SE • Turn drive wheels and compare CONSULT value with the speedometer indi-
cation. Almost the same speed as
the speedometer indication
SET VHCL SPD • Engine: Running ASCD: Operating The preset vehicle speed is
displayed
MAIN SW • Ignition switch: ON MAIN switch: Pressed On
MAIN switch: Released Off
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-93
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
1
(G) 128
(GR) Throttle control motor
(Close) Output[Ignition switch: ON]
• Engine stopped
• Selector lever: D
• Accelerator pedal: Fully released 1.8 V
2
(R) 128
(GR) Throttle control motor
power supply Input [Ignition switch: ON]
Battery voltage
(11 - 14 V)
3
(BG) 128
(GR) Throttle control motor
(Open) Output[Ignition switch: ON]
• Engine stopped
• Selector lever: D
• Accelerator pedal: Fully depressed 3.2 V
4
(W) 8
(B) Knock sensor Input [Engine is running]
• Idle speed 2.5 V
5
(W) 128
(GR) Intake manifold tuning
valve motor (Close) Output[Ignition switch ON]
• Engine coolant temperature: more than -30 °C (-22 °F)
• Accelerator pedal: Depressed → ful-
ly released Battery voltage appears for about
1 second.
6
(L) 128
(GR) Intake manifold tuning
valve motor power supply Input [Ignition switch: ON]
Battery voltage
(11 - 14 V)
7
(B) 128
(GR) Intake manifold tuning
valve motor (Open) Output[Ignition switch ON]
• Engine coolant temperature: more
than -30 °C (-22 °F)
• Accelerator pedal: Fully released →
depressed Battery voltage appears for about
1 second.
8
(B) —Sensor ground
(Knock sensor) —— —
9
(Y) 10
(BR)
13
(BR) 14
(Y) 128
(GR) Fuel injector No. 4
Fuel injector No. 3
Fuel injector No. 1
Fuel injector No. 2 Output[Engine is running]
• Warm-up condition
• Idle speed NOTE:
The pulse cycle changes depending
on rpm at idle Battery voltage
(11 - 14 V)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm Battery voltage
(11 - 14 V)
JMBIA0326GB
JMBIA0324GB
JMBIA0089GB
JMBIA0090GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-94
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
12
(B) — ECM ground — — —
16
(B) — ECM ground — — —
17
(V) 128
(GR) EVAP canister purge vol-
ume control solenoid
valve Output[Engine is running]
• Idle speed
• Accelerator pedal: Not depressed even slightly, after engine starting Battery voltage
(11 - 14 V)
[Engine is running]
• Engine speed: About 2,000 rpm (More than 100 seconds after start-
ing engine.) Battery voltage
(11 - 14 V)
18
(V) 128
(GR) Fuel pump relay Output [Ignition switch: ON]
• For 1 second after turning ignition switch ON
[Engine is running] 0 - 1.0 V
[Ignition switch: ON]
• More than 1 second after turning ig- nition switch ON Battery voltage
(11 - 14 V)
21
(BR) 128
(GR) Throttle control motor re-
lay Output[Ignition switch: OFF]
Battery voltage
(11 - 14 V)
[Ignition switch: ON] 0 - 1.0 V
22
(L) 23
(B) Heated oxygen sensor 2 Input [Engine is running]
• Revving engine from idle to 3,000 rpm quickly after the following condi-
tions are met
- Engine: after warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 0 - 1.0 V
23
(B) —Sensor ground
(Heated oxygen sensor 2) —— —
25
(L) 26
(G) Engine oil temperature
sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine oil temperature.
26
(G) —Sensor ground
(Engine oil temperature
sensor) —— —
27
(BR) —Sensor ground
(Engine coolant tempera-
ture sensor) —— —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
JMBIA0087GB
JMBIA0088GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-96
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
39
(L) 38
(V) Engine oil pressure sen-
sor Input[Engine is running]
• Warm-up condition
• Idle speed 1.3 V
[Engine is running]
• Warm-up condition
• Engine speed is 2,000 rpm 2.7 V
40
(BR) 38
(V) Sensor power supply
(Engine oil pressure sen-
sor) — [Ignition switch: ON] 5.0 V
41
(W) 128
(GR) A/F sensor 1 Input [Ignition switch: ON] 2.2 V
42
(SB) —Sensor ground
[Exhaust valve timing
control position sensor] —— —
43
(LG) 42
(SB) Exhaust valve timing con-
trol position sensor Input[Engine is running]
• Warm-up condition
• Idle speed NOTE:
The pulse cycle changes depending
on rpm at idle 1.0 - 2.0
[Engine is running]
• Engine speed is 2,000 rpm 1.0 - 2.0
44
(V) —Sensor power supply
[Exhaust valve timing
control position sensor] — [Ignition switch: ON] 5 V
45
(B) 128
(GR) A/F sensor 1 Input [Engine is running]
• Engine speed is 2,000 rpm 1.8 V
Output voltage varies with air fuel ratio.
49
(W) 128
(GR) Intake manifold runner
control valve motor
(Close) Output[Ignition switch ON]
• Engine coolant temperature: Be- tween -12 °C (10 °F) and 59 °C
(138 °F)
• Accelerator pedal: Depressed → ful-
ly released Battery voltage appears for about
1 second.
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
OutputJPBIA3359ZZ
JPBIA3360ZZ
JPBIA4730ZZ
JPBIA4731ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-101
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*1: For California
*2: Before measuring the terminal voltage, confi rm that the battery is fully charged. Refer to PG-4, "How to
Handle Battery".
Fail SafeINFOID:0000000009462122
NON DTC RELATED ITEM
11 5
(L) 128
(GR) Stop lamp switch Input [Ignition switch: OFF]
• Brake pedal: Fully released 0 V
[Ignition switch: OFF]
• Brake pedal: Slightly depressed Battery voltage
(11 - 14 V)
11 6
(BR) 128
(GR) Brake pedal position
switch Input[Ignition switch: OFF]
• Brake pedal: Fully released Battery voltage
(11 - 14 V)
11 7
(W) 128
(GR) PNP signal Input [Ignition switch: ON]
• Selector lever: P or N Battery voltage
(11 - 14 V)
[Ignition switch: ON]
• Selector lever: Except above 0 V
11 8 (G) —Sensor power supply
(Accelerator pedal posi-
tion sensor 2) — [Ignition switch: ON] 5.0 V
11 9 (P) 120
(G) Accelerator pedal posi-
tion sensor 2 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released 0.25 - 0.5 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed 2.0 - 2.5 V
120 (G) —Sensor ground
(Accelerator pedal posi-
tion sensor 2) —— —
121
(LG) 128
(GR) Power supply for ECM Input [Ignition switch: ON] Battery voltage
(11 - 14 V)
122 (V) —Sensor power supply
(Accelerator pedal posi-
tion sensor 1) — [Ignition switch: ON] 5.0 V
124
(SB) —Sensor ground
(EVAP control system
pressure sensor, refriger-
ant pressure sensor) —— —
125
(BR) 128
(GR) Fuel tank temperature
sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with fuel tank temperature
126
(SB) 127
(L) Accelerator pedal posi-
tion sensor 1 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released 0.5 - 1.0 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed 4.2 - 4.8 V
127 (L) —Sensor ground
(Accelerator pedal posi-
tion sensor 1) —— —
128
(GR) — ECM ground — — —
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-102
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
DTC RELATED ITEM
Description
When a DTC is detected, ECM executes a mode (in the
Fail-safe mode) applicable to the DTC. The fail-safe
mode has the preset traveling control mode (acceler ator angle variation and engine output limit) and device fix
mode.
Fail Safe Pattern
Fail Safe List
× :Applicable —: Not applicable
Detected
items Engine operating condition
in fail-safe mode Remarks Reference page
Malfunction
indicator
lamp circuit Engine speed will not rise
more than 2,500 rpm due
to the fuel cut When there is an open circuit on MIL circuit, the ECM cannot warn the
driver by lighting up MIL when there is malfunction on engine control
system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns the
driver that engine control system malfunctions and MIL circuit is open
by means of operating fail safe function.
The fail safe function also operates when above diagnoses except MIL
circuit are detected and demands the driver to repair the malfunction. EC-517, "Compo-
nent Function
Check"
Fail safe mode Vehicle behavior
Traveling con-
trol mode Accelerator an-
gle variation
control ECM controls the accelerator pedal depression speed to make it slower than actual speed. This
causes a drop in accelerating performance and encourages the driver to repair malfunction.
NOTE:
ECM does not control the accelerator pedal releasing speed.
Engine output
control ECM reduces the engine output, according to the rise in engine speed. This reduces the vehicle
speed to encourage the driver to repair malfunction.
Device fix mode • This mode fixes the IVT control solenoid valve and the EVT control solenoid valve in the refer-
ence position.
• The intake manifold runner control valve motor is turned OFF (intake manifold runner control
valve opens).
Pattern Fail safe mode
A Traveling control mode Accelerator angle variation control
B Engine output control
C Device fix mode
DTC No. Detected items Vehicle behavior
Pattern Others
ABC
P0011 Intake valve timing control ——×ECM activates the IVT intermediate lock control solenoid
valve to bring the cam sprocket into an intermediate lock con-
dition.
P0014
P0078 Exhaust valve timing control
——× —
P0101
P0102
P0103 Mass air flow sensor circuit
××× —
P0122
P0123
P0222
P0223
P2135 Throttle position sensor
———The ECM controls the electric throttle control actuator in reg-
ulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM