2014 MITSUBISHI OUTLANDER PHEV parking brake

NOTElIf the parking brake does not hold the vehi-
cle stationary after the foot brake is released,
have your vehicle checked immediately.
To release
1- Firmly depress and hold the brake pedal,
then pull the lever up slightly.
2- Push the button at the end of hand grip.
3- Lower the lever fully.
CAUTIONl Before driving, be sure that the parking
brake is fully released and brake warning lamp is off.
If you drive without the parking brake fully
released, the warning display will appear on the information screen in the multi informa-tion display and a buzzer sound when the ve-
hicle speed exceeds 8 km/h (5 mph).
If a vehicle is driven without releasing the
parking brake, the brake will be overheated, resulting in ineffective braking and possible
brake failure.Warning lampWarning display
l If the brake warning lamp does not extin-
guish when the parking brake is fully re-
leased, the brake system may be abnormal.
Have your vehicle checked immediately.
For details, refer to “Brake warning lamp” on page 6-42.
Parking
E00600602645
To park the vehicle, fully engage the parking brake, and then press the electrical parking
switch to lock the wheels.
Parking on a hill
To prevent the vehicle from rolling, follow these procedures:
Parking on a downhill slope
Turn the front wheels towards the kerb and
move the vehicle forward until the kerb side wheel gently touches the kerb.
Apply the parking brake and press the electri-
cal parking switch.
If necessary, apply chocks to wheels.
Parking on an uphill slope
Turn the front wheels away from the kerb
and move the vehicle back until the kerb side wheel gently touches the kerb.
Apply the parking brake and press the electri-
cal parking switch.
If necessary, apply chocks to wheels.
Parking
7-04OGGE14E5Starting and driving7

NOTElWhen operating the power switch, press the
switch all the way in. If the switch is not
fully pressed, the Plug-in Hybrid EV System
may not start or the operation mode may not change. If the power switch is pressed cor-
rectly, there is no need to hold the power switch down.
l When the battery in the keyless operation
key has worn out, or the keyless operationkey is out of the vehicle, a warning lamp
will blink for 5 seconds or a warning display will appear.
Operation mode of the power
switch and its function
OFF
The indication lamp on the power switch
turns off.
The operation mode cannot be put in OFF unless the electrical parking switch is press-
ed.
ACC
Electrical devices such as the audio and ac-
cessory socket can be operated. Can be used when the Ready indicator is off.
The indication lamp on the power switch illu- minates orange.
ON
All vehicle’s electrical devices can be operat-
ed.
The indication lamp on the power switch illu- minates blue. The indication lamp turns off
when the Plug-in Hybrid EV System is oper- ating.
NOTEl Your vehicle is equipped with an electronic
immobilizer.
To start the Plug-in Hybrid EV System, the ID code which the transponder inside the
key sends, must match the one registered in the immobilizer computer. Refer to “Elec-
tronic immobilizer (Anti-theft starting sys-
tem)” on page 4-03.Changing the operation mode
E00631901041
If you press the power switch without de-
pressing the brake pedal, you can change the
operation mode in the order of OFF, ACC,
ON, OFF.
CAUTIONl When the Plug-in Hybrid EV System is not
operating, put the operation mode in OFF.
Leaving the operation mode in ON or ACC for a long time when the Plug-in Hybrid EV
System is not operating may cause the auxil- iary battery to discharge, making it impossi-
ble to start the Plug-in Hybrid EV System.
Power switch
7-09OGGE14E5Starting and driving7

Starting and stopping thePlug-in Hybrid EV System E00620601295Starting the Plug-in Hybrid EV
System
E00620701528
CAUTIONl When the Plug-in Hybrid EV System warn-
ing lamp comes on while the READY indi- cator is on, avoid high-speed driving and
have your vehicle inspected by a
MITSUBISHI MOTORS Authorized Serv-
ice Point as soon as possible. (Refer to “Plug-in Hybrid EV System warning lamp” on page 6-44.)
l Never attempt to start the engine by pushing
or pulling the vehicle.
1. Check that the EV charging cable is not
connected to your vehicle.
2. Fasten the seat belt.
3. Make sure the parking brake is applied.
4. When you press the power switch while
depressing the brake pedal with your
right foot, the READY indicator in the meter blinks and the activation of Plug-
in Hybrid EV System starts.
NOTEl After the Plug-in Hybrid EV System has not
started for a while, the brake pedal effort
needed to start the Plug-in Hybrid EV Sys- tem may become greater. If this occurs, de- press the brake pedal more firmly than usual.
5. When the READY indicator changes
from blinking to staying on, the startup of Plug-in Hybrid EV System is activa-ted and the vehicle is now ready to drive.
CAUTIONl Do not press the power switch while holding
the select lever at the operated position.NOTEl Continue to depress the brake pedal until the
READY indicator in the meter stays on.
l You can drive your vehicle even if the en-
gine is stopped.
l The Plug-in Hybrid EV System can be star-
ted in any operation mode.
l If the READY indicator does not come on,
check the select position indicator. If the in-
dicator does not indicate “P”, press the elec- trical parking switch to display “P” position.
l If the READY indicator does not come on,
turn the power switch to OFF once and, aftera while, press the power switch to start Plu-
gin Hybrid EV System.Stopping the Plug-in Hybrid
EV System
E00620801268
1. Stop your vehicle completely.
2. Apply the parking brake firmly while
depressing the brake pedal.
3. After pressing the electrical parking
switch, press the power switch to stop Plug-in Hybrid EV System. (Refer to
“Electrical Parking switch” on page 7-14.)
WARNINGl Never stop Plug-in Hybrid EV System
during running except in emergency. The effectiveness of the brake becomes very
poor and the steering wheel becomes very
heavy, which can easily lead to an acci- dent.NOTEl Do not operate the power switch during run-
ning except in emergency. If you have tostop Plug-in Hybrid EV System in emergen-cy during running, continue to press the power switch for three seconds or longer or
press the power switch three times or more
quickly. Plug-in Hybrid EV System stops, the operation mode turns to ACC, and the
selector lever position shifts to the “P” posi- tion at very slow speed.
Starting and stopping the Plug-in Hybrid EV System
7-11OGGE14E5Starting and driving7

NOTElIf you press the power switch when the se-
lector lever position is other than “P” posi-tion while your vehicle is stopped, the selec-
tor lever position automatically shifts to “P”
position, Plug-in Hybrid EV System stops, and the power mode turns to “OFF”.
l If the parking lock mechanism is faulty, a
warning is displayed on the information
screen in the multi-information display. When this warning is displayed, Plug-in Hy-
brid EV System cannot be stopped unless you apply the parking brake and then press the power switch. Park on a flat place with
the parking brake securely applied. Have your vehicle inspected by a MITSUBISHI
MOTORS Authorized Service Point.If the keyless operation key is
not operating properly
E00632901051
Insert the keyless operation key into the key
slot. Starting the Plug-in Hybrid EV System and changing the operation mode should be now possible.
Remove the keyless operation key from the
key slot after starting the Plug-in Hybrid EV
System or changing the operation mode.NOTEl Do not insert into the key slot anything other
than the keyless operation key. This couldcause damage or a malfunction.
l Remove the object or additional key from
the the keyless operation key before insert-ing the key into the key slot. The vehicle
may not be able to receive the registered ID
code from the registered key. Therefore, the Plug-in Hybrid EV System may not start and
the operation mode may not change.
l The keyless operation key is fixed in the key
slot when inserted in the illustrated direc- tion. Simply pull out the key to remove it
from the key slot.Keyless operation key remind-
er
E00633001046
If the operation mode is in OFF and the driv- er’s door is opened with the keyless operationkey in the key slot, the outer buzzer sounds
for approximately 3 seconds and the inner buzzer sounds for approximately 1 minute or
a warning display will appear to remind you
to remove the key.
Selector Lever (Joystick
Type) E00636100054
Selector Lever (Joystick Type)
7-12OGGE14E5Starting and driving7

Selector lever operation
E00636200026
Operate the selector lever slowly and secure-ly in the following method.
● (home position) to “D” or “R”: Simply shift the lever.
● (home position) to “N”: Shift and hold at
“N” position for a while.
● (home position) to “B”: You can shift the
selector lever to “B” only when the select po- sition is in “D” position.
When shifted from ● (home position) to “B”,
the regenerative brake force will increase by one step.
When shifted to “B” once again, the regener-
ative brake force will become the maximum.
When you shift the selector lever to “D”, the select position returns to “D”.
NOTEl If you operate the select lever to (B) twice
too quickly, the regenerative brake force
may not become the maximum.
The selector lever always returns to its home
position when it is released.
WARNINGl Do not replace the selector lever knob by
anything other than a MITSUBISHI
MOTORS genuine part. In addition, do
not hang an object on the selector lever as
it may cause an accident.
l When you shift the selector lever to “D”
or “R” position, always depress the brake
pedal with your right foot for your safety. Never shift the lever while depressing the accelerator pedal. Doing so will start your
vehicle abruptly, which may lead to a seri- ous accident. It may also be a cause of failure of the vehicle.NOTEl You cannot operate the regenerative brake
while the adaptive cruise control system(ACC) is operating.
l Every time when operating the selector lev-
er, be sure to check the position displayed on the indicator.NOTEl If you perform the following operation, the
buzzer may sound and the select positionmay automatically shift to “N” position.
• Presses the electrical parking switch dur-
ing running
• Shifts the selector lever to “R” while driv-
ing forward
• Shifts the selector lever to “D” while driv-
ing backward
• Shifts the selector lever to “B” in “R” po-
sition
l If you perform the following operation, the
buzzer sounds and the select lever operation is cancelled.
• When in “P” position, shifts the selector
lever without depressing the brake pedal
• When in “P” or “N” position, shifts the
selector lever to (B)
• Operates the selector lever with the EV
charging cable connected
l If you shift and hold the selector lever for
about 15 seconds or longer, the buzzer sounds.
The buzzer stops sounding when you release
the selector lever.
l If the driver’s door is opened while the vehi-
cle is stopped or is running at very low
speed with the select position in other than “P” position and the READY indicator in
the meter is illuminating, the buzzer sounds. The buzzer stops sounding if you close the
door or shift the selector lever to “P”.
Selector Lever (Joystick Type)
7-13OGGE14E5Starting and driving7(home position)

Select Position indicatorE00636300027
This indicator displays the selector lever po- sition in the meter.
When the “B” position is selected, the selec- ted regenerative brake force position is also
displayed at “B” position.Selector lever positions
E00636400031
“P” PARK
The wheels are locked. When you park your vehicle, be sure to apply the parking brakeand press the electrical parking switch.
“R” REVERSE
This position is to back up.
“N” NEUTRAL
No power is transmitted to the wheels. The wheels are not locked.
WARNINGl Never move the selector lever to the “N”
(NEUTRAL) position while driving, youwill lose Regenerative braking.
l Always keep your right foot on the brake
pedal when shifting into or out of “N”, to minimize the risk of loss of control.
“D” DRIVE
This position is for normal driving.
“B” REGENERATIVE
BRAKE
This position is for the regenerative braking.
You can adjust the regenerative braking force up to two levels.
Refer to “Selector lever operation” on page
7-13.
WARNINGl Sudden Regenerative braking may cause
the tyres to skid.
Select this position according to the road
conditions and vehicle speed.CAUTIONl When the capacity of the drive battery is
close to full or when the drive battery tem- perature is low, the regenerative brake will
become less effective.
• In such case, depress the brake pedal
strongly.Electrical Parking switch
E00636600020
When you park your vehicle, be sure to applythe parking brake and press the electrical
parking switch to lock the wheels. The indi- cator on the switch illuminates in green and
the select position indicator displays “P” on the information screen in the meter.
Select Position indicator
7-14OGGE14E5Starting and driving7

CAUTIONlIf you operate the electrical parking switch
and the select lever repeatedly within a short
time, the shifting from the “P” position or to the “P” position is restrained for a certainperiod for the system protection. In such a
case, wait for a while and then perform the operation.
l If the parking lock mechanism is faulty, a
warning is displayed on the information
screen in the multi-information display.
When this warning is displayed, park on a flat place with the parking brake securely
applied. Have your vehicle inspected by a MITSUBISHI MOTORS Authorized Serv-
ice Point.CAUTIONl If you press the electrical parking switch be-
fore your vehicle stops completely, the vehi- cle makes a sudden stop, which may cause
injury to passengers. This also can be a cause of failure of the vehicle.
l Do not place an object around the electrical
parking switch. The electrical parking switch
may be pressed by the object when you place it there or when you somehow touch it.This will cause unintentional shifting to “P”
or “N” position, which may lead to an acci- dent.
l Be careful not to spill beverages, etc. around
the electrical parking switch. The electrical
parking switch may be stuck to the pressed
position when it is pressed.NOTEl When the selector lever is shifted from the
“P” position or to the “P” position, operatingnoise and vibration of the parking lock are felt, but this is normal.
Electrical Parking switch re-
minder buzzer
If the driver’s door is opened with the select
position other than “P” when the vehicle is at a stop, the buzzer sounds to warn to press the
electrical parking switch.
Regenerative braking level
selector (paddle)* E00636700021
Regenerative braking level selector (paddle)
can quickly change the regenerative brake force while keeping your hand on the steering
wheel when you release your foot from the
accelerator pedal while driving.
By pulling the regenerative braking level se- lector, the brake force (amount of electricalenergy to charge the drive battery) can be ad-
justed according to the driving condition such as before a curve or a downhill.
Regenerative braking level selector (paddle)*
7-15OGGE14E5Starting and driving7

NOTElIt is recommended to use the battery charg-
ing switch at least 20 minutes before you
climb towards the speed of more than
100 km/h (62 mph) or when a long slope
(gradient of more than 4 %) is expected.
(According to a towing weight, it may not be able to continue the speed.)
l When using the battery charge switch with a
vehicle that has been parked in the heath a
long time, it may not charge.
l The charging time close to the full charging
of the drive battery becomes longer depend- ing on the condition of the drive battery, a
driving condition or an environment.
l The engine may stop near full charge.
l If you press the battery charge switch in or-
der to generate electricity while using gaso-
line, the fuel consumption will suffer. We recommend you to consider the environ- ment.
l When the engine is started while parking,
there is a risk of receiving a penalty due to
idling stop ordinances.
You should use the battery charge switch that conforms to the relevant municipality.
If you press the battery charge switch in or-
der to generate electricity using gasoline, the fuel consumption will suffer.When the Battery save switch
is ON
When the battery save switch is turned on while driving in the battery charge mode, the
mode changes to the battery save mode.
If the battery charge switch is pressed, the
mode is returned to the battery charge mode.
Acoustic Vehicle Alerting
System (AVAS) E00631601051
The Acoustic Vehicle Alerting System(AVAS) is a device that uses sound to alert
pedestrians of the presence of the vehicle. The system operates when the vehicle speed
is about 35 km/h (22 mph) or less and the en-
gine is not running.
The sound starts when the AVAS is operated
in the following conditions.
l When the vehicle speed is about 3 km/h
(2 mph) or less with engine not runningand the brake pedal is not depressed.
l When the vehicle speed is about 3 km/h
(2 mph) to 35 km/h (22 mph) and engine
is not running.
The sound does not start in the following ca-
ses.
l When the vehicle speed is about 3 km/h
(2 mph) or less and the brake pedal is depressed.
l When the vehicle speed is about 35 km/h
(22 mph) or more.
l When the select position is in “P”
(PARK) position.
l When the AVAS OFF indicator in the
meter is illuminating.
l When the engine is running.
When the operation mode is set to “ON”, the
AVAS OFF indicator comes on and goes out after a few seconds.
Acoustic Vehicle Alerting System (AVAS)
7-23OGGE14E5Starting and driving7