2014 MERCEDES-BENZ CLS warning light

Yellow guide line atadistanceof
approximately 13 ft(4.0m)from the rear
of the vehicle
White guide line without turning the
steering wheel, vehicle width including
the exterior mirrors (static)
$CLSCoupe:yellow guide line for the
vehicle width including the exterior
mirrors,for current steering wheel angle
(dynamic)
!Yellow lane marking tires at current
steering wheel angle(dynamic)
Yellow guide line atadistance of
approximately3ft(1.0 m) from the rear
of the vehicle
%Vehicle center axle (marker assistance)
Bumper
Red guide line atadistance of
approximately 12 in (0.30 m) from the
rear of the vehicle
The guide linesare shownwhen the
transmission is in positionR.
The distance specifications only apply to
objectsthat are at ground level.
Additional messages for vehicles withPARKTRONIC
Front warning display
Additional PARKTRONIC measurement
operational readiness indicator
$Rear warning display
Vehicles with PARKTRONIC:if
PARKTRONIC is operational (Ypage 193), an
additional operational readiness indicator will
appearinCOMAND display.Ifthe
PARKTRONIC warning displays are active or
light up, warning displaysand$are also
active or light up correspondingly in the
COMAND display.
Driving systems201
Driving and parking
Z

Warning and display messages in the
multifunction display
XActivate ATTENTION ASSIST using the on-
board computer (Ypage228).
If ATTENTION ASSIST is active, you willbe
warned no sooner than 20 minutes after
yourjourney has begun. You then hear an
intermittent warning tonetwice and the
Attention Assist:Drowsiness
detectedmessage appears in the
multifunction display.
XIf necessary, takeabreak.
XPressthebutton to confirmthe
message.
On longjourneys, takeregular breaksingood
timetoallow yourself to rest properly. If you
do not takeabreak,you will be warned again
after 15 minutes at theearliest. The
preconditionfor this is that
ATTENTION ASSIST still detectstypical
indicators of fatigue or increasing lapses in
concentration.
When ATTENTION ASSIST is deactivated, the

symbol and OFF appear in the
multifunction display in the assistance
graphics display when the engine is running.
ATTENTION ASSIST is reset when you
continue your journey and startsassessing
your tiredness again if:
Ryou switch off the engine.
Ryou take off your seat belt and open the
driver's door, e.g. forachange of drivers or
to takeabreak.
Night View Assist Plus
Important safety notes
Night View Assist Plus is only an aid and is not
asubstitute for attentive driving. Do not rely
on the Night View Assist Plus display.You are
responsible for the distance to the vehicle in
front,for vehicle speed and for braking in
good time. Drive carefully and always adapt
your driving style to suit the prevailing road
and traffic conditions.
The system may be impaired or may not
function if:
Rthere is poor visibility, e.g. due to snow,
rain, fog or spray
Rthe windshield is dirty, fogged up or
covered, for instance byasticker, in the
vicinityofthe camera
Ron bends, on uphill gradients or downhill
gradients
Pedestrian recognition may be impaired or
inoperative if:
Rpedestrians are partially or entirely
obscured by objects, e.g. parked vehicles
Rthe silhouette of the pedestrian in the Night
View Assist Plus display is incompleteor
interrupted, e.g. by powerful light
reflections
Rpedestrians do not contrast adequately
from the background
Rpedestrians are not in an upright position,
e.g. sitting, squatting or lying
In addition to the illumination provided by the
normal headlamps, Night View Assist Plus
uses infrared light to illuminate the road.
Night View Assist Plus camerapicks up
the infrared light and displaysamonochrome
image in COMAND. The image displayed in
COMAND corresponds toaroad lit up by high-
beam headlamps. This enables you to see the
road's course and any obstacles in good time.
If pedestrian recognition is activated,
pedestrians recognized by the system are
204Driving systems
Driving and parking

pedestrians cannot be gaged accurately by
lookingatascreen.
It may be the case that objects are highlighted
as well as pedestrians.
Fogged up or dirty windshield
GWARNING
Always rememberthat you must concentrate
primarily on driving the vehicle.Adriver's
attention to the road must always be his/her
primary focus when driving. For your safety
and the safety of others: stop the vehicle
before attempting to clean fogged up
windows or the windshield area in front of the
Night View Assist Plus camera.
Please remember that when your vehicle is
traveling ataspeed of only 30 mph
(approximately 50 km/h)itcoversadistance
of 44 ft (approximately 14 m) per second.
If the windshield in front of the camera is
fogged up or dirty on the inside or outside, the
Night View Assist Plus displayisaffected.
XTo defrost:check the automatic air
conditioning settings (Ypage 140) and fold
down the camera cover (Ypage 316).
XTo defrost the inside of the windshield:
fold down the camera cover (Ypage 316)
and clean the windshield(Ypage 314).
206Driving systems
Driving and parking

This device has been approved by the FCC
asa"Vehicular RadarSystem". The radar
sensor is intended foruse in an automotive
radar system only. Removing, tampering
with, or altering the device will void any
warranties, and is not permitted by the
FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this
device could void the user’s authority to
operate the equipment.
Monitoring range of the sensors
In particular, the detection of obstacles can
be impaired if:
Rdirt on the sensors or anything else
covering the sensors
Rpoor visibility, e.g. due to fog, heavy rain,
snow or spray
Rnarrow vehicles, e.g. motorcycles or
bicycles
Rthe road has very wide lanes
Rthe road has narrow lanes
Ryou are not driving in the middle of the lane
Rthere are barriers or similarlane borders
Vehiclesinthemonitoringrangeare then not
indicated.
BlindSpotAssist monitors the area up to
10 ft (3 m) behind your vehicle and directly
next to your vehicle, as shown in the diagram.
If the lanes are narrow, vehicles driving in the
lane beyond the lane next to your vehicle may
be indicated, especially if the vehicles are not
driving in the middle of their lane. This may
be the case if there are vehicles driving at the
inner edge of their lanes.
Due to the nature of the system:
Rwarnings may be issued in error when
driving close to crash barriers or similar
solid lane borders.
Rthe warning is canceled when driving for an
extended period next to long vehicles, such
as trucks.
The two radar sensors for Blind Spot Assist
are integrated into the sides of the rear
bumper. Make sure that the bumper is free of
dirt, ice or slush in the vicinity of the sensors.
The sensors must not be covered, for
example by cycle racks or overhanging loads.
Followingasevere impact or in the event of
damage to the bumpers, have the function of
the sensors checked ataqualified specialist
workshop. Blind Spot Assist may otherwise
not work properly.
Indicator and warning display
Yellowindicator lamp/red warning lamp
Active Blind Spot Assist is not active at
speeds below approximately 20 mph
(30 km/h). Vehicles in the monitoring range
are then not indicated.
When Blind Spot Assist is activated, indicator
lampin the exterior mirrors lights up
yellow at speeds of up to 20 mph(30km/h).
At speeds above 20 mph (30 km/h) the
208Driving systems
Driving and parking

indicator lamp goes out and BlindSpot Assist
is operational.
Ifavehicle is detected within the monitoring
rangeofBlindSpot Assist at speeds above
20 mph (30 km/h), warninglampon the
correspondingside lightsupred. This warning
is always emitted whenavehicle enters the
blind spot monitoring rangefrom behind or
from the side.When you overtakeavehicle,
the warning only occurs if the difference in
speed is less than7mph (12km/h).
The yellow indicator lamp goes out if reverse
gear is engaged. In this event,Blind Spot
Assist is no longer active.
The brightness of the indicator/warning
lamps is adjusted automatically according to
the ambient light.
Collision warning
Ifavehicle is detected in the monitoring range
of Blind Spot Assist and you switchonthe
correspondingturn signal,adouble warning
tonesounds. Red warning lampflashes. If
the turn signal remains on, vehicles detected
are indicated by the flashing of red warning
lamp.There are no further warning tones.
Switching on Blind Spot Assist
XMake sure that Blind Spot Assist
(Ypage 228) is activated in the on-board
computer.
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Lane Keeping Assist
Important safety notes
GWARNING
Lane Keeping Assist may not always clearly
recognizelane markings.
In this case, Lane Keeping Assist may:
Rgive an unnecessary warning
Rnot giveawarning
There isarisk of an accident.
Always pay particular attention to the traffic
situation and stay in lane, in particular if
warned by Lane Keeping Assist.
GWARNING
The Lane Keeping Assist warning does not
return the vehicle to the original lane. There
isarisk of an accident.
You should always steer, brake or accelerate
yourself, in particular if warned by Lane
Keeping Assist.
If you fail to adapt your driving style, Lane
Keeping Assist can neither reduce the risk of
an accident nor override the laws of physics.
Lane Keeping Assist cannot take into account
the road, traffic and weather conditions. Lane
Keeping Assist is merely an aid. You are
responsible for the distance to the vehicle in
front,for vehicle speed, for braking in good
time and for staying in your lane.
The Lane Keeping Assist does not keep the
vehicle in the lane.
The system may be impaired or may not
function if:
Rthere is poor visibility, e.g. due to
insufficient illumination of the road, or due
to snow, rain, fog or spray
Rthere is glare, e.g. from oncomingtraffic,
the sun or reflections (e.g. when the road
surface is wet)
Rthe windshield is dirty, fogged up, damaged
or covered, for instancebyasticker, in the
vicinity of the camera
Rthere are no, several or unclear lane
markings foralane, e.g. in areas with road
construction work
Rthe lane markings are worn away,dark or
covered up, e.g. by dirt or snow
Driving systems209
Driving and parking
Z

specialist workshop. Active Blind Spot Assist
may otherwise no longer work properly.
Monitoring area
GWARNING
Active Blind Spot Assist does not detect all
traffic situations and road users. There is a
risk of an accident.
Always make sure that there is sufficient
distance on the side for other traffic or
obstacles.
Active Blind Spot Assist monitors the area up
to 10 ft (3.0 m) behind your vehicle and
directly next to your vehicle, as shown in the
diagram.
The detection of obstacles can be impaired in
the case of:
Rdirt on the sensors or anything else
covering the sensors
Rpoor visibility, e.g. due to rain, snow or
spray
Vehicles in the monitoring range are then not
indicated or indicated withadelay.
Active Blind Spot Assist may not detect
narrow vehicles, such as motorcycles or
bicycles, or may only detect them too late.
If the lanes are narrow, vehicles driving in the
lane beyond the lane next to your vehicle may
be indicated, especially if the vehicles are not
driving in the middle of their lane. This may
be the case if there are vehicles at the edge
of their lane.
Due to the nature of the system:
Rwarnings may be issued in error when
driving close to crash barriers or similar
solid lane borders.
Rthe warning is canceled when driving for an
extended period next to long vehicles, such
as trucks.
Indicator and warning display
Yellowindicator lamp/red warning lamp
Active Blind Spot Assist is not active at
speeds below approximately 20 mph
(30 km/h). Vehicles in the monitoring range
are then not indicated.
When active Blind Spot Assist is activated,
indicator lampin the exterior mirrors lights
up yellow at speeds of up to
20 mph(30 km/h). At speeds above 20 mph
(30 km/h), the indicator lamp goes out and
active Blind Spot Assist is operational.
Ifavehicle is detected within the monitoring
range of Blind Spot Assist at speeds above
20 mph (30 km/h), warning lampon the
corresponding side lights up red. This warning
is always given whenavehicle enters the
blind spot monitoring range from behind or
from the side. When you overtakeavehicle,
the warning only occurs if the difference in
speed is less than7mph (12km/h).
The yellow indicator lamp goes out if reverse
gear is engaged. In this event,Active Blind
Spot Assist is no longer active.
212Driving systems
Driving and parking

The brightness of the indicator/warning
lamps is adjusted automatically accordingto
the ambient light.
Visual and acoustic collision warning
If you switch on the turn signals to change
lanes andavehicle is detected in the side
monitoring range, you receiveavisual and
acoustic collision warning. You then hear a
double warning toneand red warning
lampflashes. If the turn signal remains on,
detected vehicles are indicated by the
flashing of red warning lamp.There are no
further warning tones.
Course-correcting brake application
GWARNING
Acourse-correctingbrake application cannot
alwayspreventacollision. There isarisk of
an accident.
Always steer, brake or accelerate yourself,
especially if Active Blind Spot Assist warns
you or makesacourse-correcting brake
application. Always maintainasafe distance
at the sides.
If Active Blind Spot Assist detectsarisk of a
lateral collision in the monitoring range, a
course-correcting brake application is carried
out. This is meant to assist you in avoiding a
collision.
Ifacourse-correcting brake application
occurs, red warning lampflashes in the
exterior mirror andadual warning tone
sounds. In addition, the display shown in the
lower image appears in the multifunction
display.
In very rare cases, the system may make an
inappropriate brake application. An
inappropriate course-correcting brake
application may be interrupted at any time if
you steer slightly in the opposite direction or
accelerate, for example.
The course-correcting brake application is
available in the speed range between
20 mph (30 km/h) and 120 mph (200 km/h).
Either no braking application, oracourse-
correcting brake application adapted to the
driving situation occurs if:
Rthere are vehicles or obstacles, e.g. crash
barriers, located on both sides of your
vehicle.
Ravehicle approaches you too closely at the
side.
Ryou have adoptedasporty driving style with
high cornering speeds.
Ryou clearly brake or accelerate.
Radriving safety system intervenes, e.g.
ESP®or PRE-SAFE®Brake.
RESP®is switched off.
Raloss of tire pressure oradefectivetire is
detected.
Switching on Active Blind Spot Assist
XMake sure that the radar sensor system
(Ypage 232) and Active Blind Spot Assist
(Ypage 228) are activated in the on-board
computer.
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Driving systems213
Driving and parking
Z

Rthe roadisnarrow and winding
Rthere arestrong shadows castonthe lane
If no vehicle is detected in the adjacent lane
and there are broken lane markings detected,
no lane-correcting brake application is made.
Warning vibration in the steering wheel
Awarning may be given ifafront wheel
passes overalane marking. It will warn you
by means of intermittent vibration in the
steering wheel for up to 1.5 seconds.
Lane-correcting brake application
GWARNING
Alane-correcting brake application cannot
always bring the vehicle back into the original
lane. There isarisk of an accident.
Always steer, brake or accelerate yourself,
especially if Active Lane Keeping Assist warns
you or makesalane-correcting brake
application.
GWARNING
Active Lane Keeping Assist does not detect
traffic conditionsorroad users. In very rare
cases, the system may make an inappropriate
brake application, e.g. after intentionally
driving overasolid lane marking. There is a
risk of an accident.
An inappropriate brake application may be
interrupted at any time if you steer slightly in
the opposite direction. Always make sure that
there is sufficient distance on the side for
other traffic or obstacles.
If you leave your lane, under certain
circumstances the vehicle will brake briefly
on one side. This is meant to assist you in
bringing the vehicle back to the original lane.
Ifalane-correcting brake application occurs,
displayappears in the multifunction
display.
This function is available in the range between
40 mph and 120 mph (60 km/h and
200 km/h).
Alane-correcting brake application can only
be made after driving overasolid,
recognizable lane marking. Before this, a
warning must be given by means of
intermittent vibration in the steering wheel.
In addition,alane with lane markings on both
sides must be recognized. The brake
application also slightly reduces vehicle
speed.
iAfurther lane-correcting brake
application can only occur after your
vehicle has returned to the original lane.
No lane-correcting brake application occurs
if:
Ryou clearly and actively steer, brake or
accelerate.
Ryou cut the corner onasharp bend.
Ryou have switched on the turn signals.
Radriving safety system intervenes, e.g.
ESP®,PRE-SAFE®Brake or Active Blind
Spot Assist.
Ryou have adoptedasporty driving style with
high cornering speeds or high rates of
acceleration.
RESP®is switched off.
Rthe transmission is not in positionD.
Raloss of tire pressure oradefective tire has
been detected and displayed.
Active Lane Keeping Assist may is unable to
detect other road or traffic conditions. An
inappropriate brake application may be
interrupted at any time if you:
Driving systems215
Driving and parking
Z