2014 Lexus IS300h indicator

5068-2. Steps to take in an emergency
IS300h_EE(OM53C61E)*
1: Parking brake engaged warning buzzer:
→P. 5 1 3
*2: Open door warning buzzer:
→P. 5 1 1
*3: Seat belt warning buzzer:
The seat belt warning buzzer sounds to alert the driver, front passenger and rear pas-
sengers that his or her seat belt is not fastened. The buzzer sounds for 30 seconds
after the vehicle reaches a speed of 20 km/h (12 mph). Then, if the seat belt is still
unfastened, the buzzer will sound in a different tone for 90 more seconds.
■Passenger detection sensor, seat belt reminder and warning buzzer
●If luggage is placed on a passenger seat, the passenger detection sensor may cause the
warning light to flash and the warning buzzer to sound even if a passenger is not sitting
in the seat.
●If a cushion is placed on the seat, the sensor may not detect a passenger, and the warn-
ing light may not operate properly.
■If the malfunction indicator lamp comes on while driving
The malfunction indicator lamp will come on if the fuel tank becomes completely empty.
If the fuel tank is empty, refuel the vehicle immediately. The malfunction indicator lamp
will go off after several trips.
If the malfunction indicator lamp does not go off, contact any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional as soon as possible.
■Electric power steering system warning light (warning buzzer)
When the 12-volt battery charge becomes insufficient of the voltage temporarily drops,
the electric power steering system warning light may come on and the warning buzzer
may sound.
■When the tire pressure warning light comes on
Carry out the following procedure after the tire temperature has lowered sufficiently.
●Check the tire inflation pressure and adjust to the appropriate level.
●If the warning light does not go out even after several minutes, check that the tire infla-
tion pressure is at the specified level and carry out initialization.
The warning light may come on again if the above operations are conducted without first
allowing the tire temperature to lower sufficiently.
■The tire pressure warning light may come on due to natural causes
The tire pressure warning light may come on due to natural causes such as natural air
leaks and tire inflation pressure changes caused by temperature. In this case, adjusting
the tire inflation pressure will turn off the warning light (after a few minutes).
■Conditions that the tire pressure warning system may not function properly
→P. 4 5 4
IS300h_EE_OM53C61E.book 506 ページ ２０１４年５月２０日　火曜日　午後５時４０分

5188-2. Steps to take in an emergency
IS300h_EE(OM53C61E)
(If equipped)
Indicates that all maintenance listed in the maintenance
schedule*1 corresponding to the current vehicle mile-
age is necessary.
(The indicator will not work properly unless the mainte-
nance data has been reset.)
→Perform the necessary maintenance. Please reset
the maintenance data after the maintenance is per-
formed (→P. 4 4 2 )
(If equipped)
Indicates that the Automatic High Beam switch is
pressed while the headlights are in low beam.
→Turn the high beam on and press the Automatic
High Beam switch again.
(If equipped)
Indicates that, since the VSC (Vehicle Stability Control)
system was turned off, the pre-crash brake system oper-
ation is stopped
→Tu r n t h e V S C o n . (→P. 2 8 8 )
(If equipped)
Indicates that the PCS (Pre-Crash Safety system) is not
currently functional because the grille cover or the sen-
sor is dirty
→Check the grille cover and the sensor and clean
them if they are dirty.
Indicates that operation of large electricity consuming
systems such as the air conditioning system are sus-
pended
→Stop using unnecessary electric components to
reduce electricity consumption. Wait a while until
the electric power supply is restored.
(If equipped)
Indicates that the LDA (Lane Departure Alert) system
cannot be used because the vehicle speed is lower than
approximately 50 km/h (32 mph)
→Drive the vehicle at 50 km/h (32 mph) or higher.
Wa r n i n g m e s s a g eDetails/Actions
(Flashes)
IS300h_EE_OM53C61E.book 518 ページ ２０１４年５月２０日　火曜日　午後５時４０分

5378-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53C61E)
■If the tire is inflated to more than the recommended level
Disconnect the hose from the valve.
Disconnect the hose from the valve, remove the air release cap from the hose and then
reconnect the hose.
Turn the compressor switch on and wait for several seconds, then turn it off. Check that
the air pressure indicator shows the recommended level. (→P. 5 6 8 )
If the air pressure is lower than the recommended level, turn the compressor switch on
again and repeat the inflation procedure until the recommended pressure is reached. Install the air release cap to the end of the
hose and push the protrusion on the air
release cap into the valve to let some air out.
CAUTION
■Caution while driving
Observe the following precautions.
Failure to do so may cause an accident.
●The emergency tire puncture repair kit is made exclusively for your vehicle. Do not
use it on other vehicles.
●Do not use the emergency tire puncture repair kit for tires that are a different size
than the specified ones or for any other purpose. Doing so may cause the tires to not
be repaired properly.
■Precautions for use of the sealant
●Ingesting the sealant is hazardous to your health. If you ingest sealant, consume as
much water as possible, then immediately consult a doctor.
●If sealant gets in eyes or adheres to skin, immediately wash it off with water. If discom-
fort persists, consult a doctor.
1
2
3
4
IS300h_EE_OM53C61E.book 537 ページ ２０１４年５月２０日　火曜日　午後５時４０分

5398-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53C61E)
NOTICE
■When performing an emergency repair
●Perform the emergency repair without removing the nail or screw that has punctured
the tread of the tire. If the object that has punctured the tire is removed, repair by the
emergency tire puncture repair kit may not be possible.
●The kit is not waterproof. Make sure that the kit is not exposed to water, such as when
it is being used in the rain.
●Do not put the kit directly onto dusty ground such as sand at the side of the road. If the
kit vacuums up dust etc., a malfunction may occur.
●Use the kit with the top facing upward. The kit cannot work properly if it is laid on its
side.
■Handling the emergency tire puncture repair kit
●The compressor power source should be 12 V DC suitable for vehicle use. Do not
connect the compressor to any other source.
●If gasoline splatters on the kit, the kit may deteriorate. Take care not to allow gasoline
to contact it.
●Store the kit in its assigned place out of reach of children.
●Do not disassemble or modify the kit. Do not subject parts such as the air pressure
indicator to impacts. This may cause a malfunction.
■To avoid damage to the tire pressure warning valves and transmitters
When a tire is repaired with liquid sealants, the tire pressure warning valve and trans-
mitter may not operate properly. If a liquid sealant is used, contact any authorized
Lexus dealer or repairer, or another duly qualified and equipped professional as soon
as possible. Make sure to replace the tire pressure warning valve and transmitter when
replacing the tire. (→P. 4 5 1 )
IS300h_EE_OM53C61E.book 539 ページ ２０１４年５月２０日　火曜日　午後５時４０分

5488-2. Steps to take in an emergency
IS300h_EE(OM53C61E)
Connect the jumper cables according to the following procedure:
Connect a positive jumper cable clamp to the exclusive jump starting ter-
minal on your vehicle.
Connect the clamp on the other end of the positive cable to the positive (+)
battery terminal on the second vehicle.
Connect a negative cable clamp to the negative (-) battery terminal on the
second vehicle.
Connect the clamp at the other end of the negative cable to a solid, station-
ary, unpainted metallic point away from the exclusive jump starting terminal
and any moving parts, as shown in the illustration.
Start the engine of the second vehicle. Increase the engine speed slightly and
maintain at that level for approximately 5 minutes to recharge the 12-volt bat-
tery of your vehicle.
Open and close any of the doors of your vehicle with the power switch off.
Maintain the engine speed of the second vehicle and start the hybrid system
of your vehicle by turning the power switch to ON mode.
Make sure the “READY” indicator comes on. If the indicator does not come
on, contact any authorized Lexus dealer or repairer, or another duly qualified
and equipped professional.3
1
2
3
4
4
5
6
7
IS300h_EE_OM53C61E.book 548 ページ ２０１４年５月２０日　火曜日　午後５時４０分

5558-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53C61E)
CAUTION
■When inspecting under the hood of your vehicle
Observe the following precautions.
Failure to do so may result in serious injury such as burns.
●If steam is seen coming from under the hood, do not open the hood until the steam
has subsided. The engine compartment may be very hot.
●After the hybrid system has been turned off, check that the “READY” indicator is off.
When the hybrid system operating, the gasoline engine may automatically start, or
the cooling fan may suddenly operate even if the gasoline engine stops. Do not touch
or approach rotating parts such as the belt and fan, which may lead to fingers or
clothing (especially a tie, a scarf or a muffler) getting caught, resulting in serious
injury.
NOTICE
■When adding engine/power control unit coolant
Add coolant slowly after the hybrid system has cooled down sufficiently. Adding cool
coolant to a hot hybrid system too quickly can cause damage to the hybrid system.
■To prevent damage to the cooling system
Observe the following precautions:
●Avoid contaminating the coolant with foreign matter (such as sand or dust etc.).
●Do not use any coolant additive.
●Do not loosen the coolant reservoir caps or
water filler cap while the hybrid system and
radiator are hot.
High temperature steam or coolant could
spray out.
IS300h_EE_OM53C61E.book 555 ページ ２０１４年５月２０日　火曜日　午後５時４０分

5749-2. Customization
IS300h_EE(OM53C61E)
Some function settings are changed simultaneously with other functions being
customized. Contact any authorized Lexus dealer or repairer, or another duly
qualified and equipped professional.
Vehicles with a Remote Touch or Lexus Display Audio controller: Settings that
can be changed using the Remote Touch or Lexus Display Audio controller
Vehicles with a Remote Touch or Lexus Display Audio controller: Settings that
can be changed using the meter control switches
Vehicles without a Remote Touch or Lexus Display Audio controller: Settings
that can be changed using the meter control switches
Settings that can be changed by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional
Definition of symbols: O = Available, — = Not available
■Gauges, meters and multi-information display (→P. 104, 109, 115)
Customizable features
1
2
3
4
Function*1Default settingCustomized setting
Language*2English
French
—OO—
German
Spanish
Italian
Russian
Units*2km (L/100 km)km (km/L)—OO—miles (MPG)
Maintenance system
initializationOFFON—OO—
EV indicatorON
(Self-lighting)OFF—OO—
switch settings*3Drive
information 1Desired status
screen
*4—OO—
Drive information 1
Current fuel
economy
*5—OO—Average fuel
economy (after
reset)
1234
IS300h_EE_OM53C61E.book 574 ページ ２０１４年５月２０日　火曜日　午後５時４０分

575
9 9-2. Customization
Vehicle specifications
IS300h_EE(OM53C61E)
*1: For details about each function: →P. 1 1 7
*2: The default setting varies according to country.
*3:Except F SPORT models
*4: Some status screens cannot be registered (indicated on multi-information display).
*5: 2 of the following items: current fuel consumption, average fuel economy (after reset),
average fuel economy (after refuel), average fuel economy (after start), average vehi-
cle speed (after reset), average vehicle speed (after start), distance (driving range),
distance (after start), elapsed time (after reset), elapsed time (after start), blank.
*6:F SPORT models
*7: The customized setting varies according to country.
Drive information 2
Distance
(range)
*5—OO—Average speed
(after reset)
Pop-up displayONOFF—OO—
Accent color*3BlueRedOOO—
Tachometer settingsON (Self-
changing)
Hybrid System Indi-
cator (Always)
—OO—Tachometer
(Always)
Needle*6BlueRed—OO—White
Speed indicator*6OFF
50 to 200 km/h
(30 to 125 mph)
*7
—OO—50 to 160 km/h
(30 to 100 mph)*7
REV indicator*64000 r/min
2000 to 6000
r/m i n
—OO—
OFF
REV peak*6ONOFF—OO—
Function*1Default settingCustomized setting1234
IS300h_EE_OM53C61E.book 575 ページ ２０１４年５月２０日　火曜日　午後５時４０分