2014 Lexus CT200h light

952. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76135E_(EE)
*1: These lights turn on when the power switch is turned to the ON mode to indicate thata system check is being performed. They will turn off after the hybrid system is on, or
after a few seconds. There may be a malfunction in a system if the lights do not turn on,
or turn off. Have the vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional.
*2: The light flashes to indicate that the system is operating.
*3: The light comes on when the system is turned off. The light flashes faster than usual to indicate that the system is operating.
*4: This light illuminates on the center panel. Shift position indicators
(
→ P. 1 8 3 )
*1, 4“PASSENGER AIR
BAG” indicator
(→ P. 5 1 )
WA R N I N G
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not come on when
you start the hybrid system, this could mean that these systems are not available to help
protect you in an accident, which could result in death or serious injury. Have the vehi-
cle inspected by any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional immediately if this occurs.
CT200h_OM_OM76135E_(EE).book Page 95 Friday, May 30, 2014 11 :14 AM

982. Instrument cluster
CT200h_OM_OM76135E_(EE)
Switches between odometer and trip
meter displays. When the trip meter is
displayed, pressing and holding the
button will reset the trip meter.
The brightness of the instrument panel lights can be adjusted by turning the dial. Brighter
Darker
When the headlight switch is turned to
ON, the brightness will be reduced
slightly unless the control dial is turned
fully up.
When the dial is turned fully down, the
cup holder light and the footwell lights
will turn off. ( →P. 4 2 6 )
■The meters and display illuminate when
The power switch is in ON mode.
■Hybrid System Indicator
Changing the display
Instrument panel light control
1
2
Po w e r a re a
Shows that an Eco-friendly driving range is
being exceeded (during full power driving
etc.)
Eco area
Shows that the vehicle is being driven in an
Eco-friendly manner.
Hybrid Eco area
Shows that gasoline engine power is not
being used very often.
The gasoline engine will automatically stop
and restart under various conditions.
Charge area
Shows that energy is being recovered via the
regenerative brake.1
2
3
4
CT200h_OM_OM76135E_(EE).book Page 98 Friday, May 30, 2014 11 :14 AM

992. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76135E_(EE)
●Hybrid System Indicator is displayed when the driving mode is in other than the sport
mode.
●By keeping the indicator needle within Ec o area, more Eco-friendly driving can be
achieved.
●Charge area indicates regeneration* status. Regenerated energy will be used to
charge the hybrid battery (traction battery).
*: When used in this manual, “regeneration” refers to the conversion of energy created
by the movement of the vehicle into electrical energy.
■Tachometer (if equipped)
The tachometer is displayed when the driving mode is in the sport mode.
■ECO lamp and SPORT lamp (if equipped)
●When sport mode is selected, the SPORT lamp (red) will illuminate.
●When all of the following conditions are satisfied and the Eco-friendly driving, the ECO
lamp (blue) will illuminate:
• Driving with the shift position in D
• Either normal mode or Eco drive mode is selected, and EV drive mode is not in use
( → P. 1 8 1 , 2 3 7 )
• The vehicle speed is approximately 130 km/h (80 mph) or below.
■Engine speed
On hybrid vehicles, engine speed is precis ely controlled in order to help improve fuel
efficiency and reduce exhaust emissions etc.
There are times when the engine speed that is displayed may differ even when vehicle
operation and driving co nditions are the same.
■Outside temperature display
●In the following situations, the correct outside temperature may not be displayed, or the
display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 20 km/h [12 mph])
• When the outside temperature has changed suddenly (at the entrance/exit of a
garage, tunnel, etc.)
●When “--” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to any authorized Lexus de aler or repairer, or another duly qualified
and equipped professional.
■Customization
Settings (e.g. on/off operation of the ECO lamp) can be changed.
(Customizable features: →P. 5 8 9 )
NOTICE
■To prevent damage to the engine and its components
●Vehicles with tachometer: Do not let the indicator needle of the tachometer enter the
red zone, which indicates the maximum engine speed.
●The engine may be overheating if the high coolant temperature warning light comes
on or flashes. In this case, immediately stop the vehicle in a safe place, and check the
engine after it has cooled completely. ( →P. 5 7 1 )
CT200h_OM_OM76135E_(EE).book Page 99 Friday, May 30, 2014 11 :14 AM

1022. Instrument cluster
CT200h_OM_OM76135E_(EE)
■Setting
→P. 5 8 9
■Display off
A blank screen is displayed
■System check display
After turning the power switch to ON mode , opening image is displayed while system
operation is checked. When the system check is complete, the normal screen will return.
■When disconnecting and reconnecting 12-volt battery terminals
The drive information will be reset.
■Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is characteristic
of liquid crystal displays, and there is no problem continuing to use the display.
NOTICE
■The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal information
display. At extremely low temperatures, the information display monitor may respond
slowly, and display changes may be delayed.
CT200h_OM_OM76135E_(EE).book Page 102 Friday, May 30, 2014 1 1:14 AM

1052. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76135E_(EE)
■Distance (driving range/after start)*1
Displays the estimated maximum distance that can be driven with the quantity
of fuel remaining and the distance driven after the hybrid system was started
respectively.
• This distance is computed based on your average fuel consumption. As a result,the actual distance that can be driven may differ from that displayed.
• When only a small amount of fuel is added to the tank, the display may not be
updated.
When refueling, turn the power switch off. If the vehicle is refueled without turning
the power switch off, the display may not be updated.
■Energy monitor
→ P. 1 0 6
■Display off
A blank screen is displayed
*1: Displayed when the item is set in “D rive Info 1” or “Drive Info 2”. (→P. 5 8 9 )
*2: The function can be reset by pressing the of the meter control switches for longer
than 1 second when the item to reset is displayed.
If there is more than one item that can be reset, the item selection screen will appear.
■System check display
After turning the power switch to ON mode , opening image is displayed while system
operation is checked. When the system check is complete, the normal screen will return.
■Po p - u p d i s p l a y
In some situations, a pop-up display will be temporarily displayed on the multi-informa-
tion display.
The following pop-up displays can be set on/off. ( →P. 5 8 9 )
• Route guidance display of the navigati on system-linked system (if equipped)
• Incoming call display of the hands-free phone system (if equipped)
■When disconnecting and reconnecting 12-volt battery terminals
The drive information will be reset.
■Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is characteristic
of liquid crystal displays, and there is no problem continuing to use the display.
NOTICE
■The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal information
display. At extremely low temperatures, the information display monitor may respond
slowly, and display changes may be delayed.
CT200h_OM_OM76135E_(EE).book Page 105 Friday, May 30, 2014 1 1:14 AM

1092. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76135E_(EE)
These images are examples only, and may vary slightly from actual conditions.
■Multi-information display screen
Hybrid battery (trac-
tion battery) status
LowFullLowFull
Navigation system screenLexus Display Audio screen
Monochrome displayColor display
When the vehicle is
powered by the
electric motor (trac-
tion motor)
When the vehicle is
powered by both the
gasoline engine and
the electric motor
(traction motor)
When the vehicle is
powered by the gas-
oline engine
When the vehicle is
charging the hybrid
battery (traction bat-
tery)
CT200h_OM_OM76135E_(EE).book Page 109 Friday, May 30, 2014 11:14 AM

1102. Instrument cluster
CT200h_OM_OM76135E_(EE)
These images are examples only, and may vary slightly from actual conditions.
■Trip information
XNavigation system screen
Press the “MENU” button on the Remote Touch, and then select “Car” on the
“Menu” screen.
If the “Energy monitor” or “Past record” sc reen is displayed, select “Trip informa-
tion”.
Resetting the consumption data
Fuel consumption in the past 15
minutes
Current fuel consumption
Regenerated energy in the past
15 minutes
One symbol indicates 30 Wh.
Up to 5 symbols are shown.
Average vehicle speed since the hybrid system was started.
Elapsed time since the hybrid system was started.
Cruising range ( →P. 112)
When there is no
energy flow
Hybrid battery (trac-
tion battery) status
LowFullLowFull
Fuel consumption (vehicles with a n avigation system or Lexus Display
Audio system)
Monochrome displayColor display
1
2
3
4
5
6
7
CT200h_OM_OM76135E_(EE).book Page 110 Friday, May 30, 2014 1 1:14 AM

1153-1. Key information
3
Operation of each component
CT200h_OM_OM76135E_(EE)
To take out the mechanical key:
Electronic keys: Slide the release lever
and take the key out.
Card key: Press the lock release button
and take the key out.
The mechanical key can only be
inserted in one direction, as the key only
has grooves on one side. If the key can-
not be inserted in a lock cylinder, turn it
over and re-attempt to insert it.
After using the mechanical key, store it
in the electronic key. Carry the mechan-
ical key together with the electronic key.
If the electronic key battery is depleted
or the entry function does not operate
properly, you will need the mechanical
key. (→P. 5 6 5 )
■Panic mode (if equipped)
Using the mechanical key
When is pressed for longer than about one
second, an alarm will sound intermittently and
the vehicle lights will flash to deter any person
from trying to break into or damage your vehi-
cle.
To stop the alarm, press any button on the elec-
tronic key.
CT200h_OM_OM76135E_(EE).book Page 115 Friday, May 30, 2014 1 1:14 AM