2014 Lexus CT200h clock

4587-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
■Adding engine oil
If the oil level is below or near the
low level mark, add engine oil of the
same type as that already in the
engine.
Make sure to check the oil type and prepare the items needed before adding
oil.Remove the oil filler cap by turning it counterclockwise.
Add engine oil slowly, checking the dipstick.
Install the oil filler cap by turning it clockwise.
■Engine oil consumption
A certain amount of engine oil will be consumed while driving. In the following situations,
oil consumption may increase, and engine oil may need to be refilled in between oil
maintenance intervals.
●When the engine is new, for example directly after purchasing the vehicle or after
replacing the engine
●If low quality oil or oil of an inappropriate viscosity is used
●When driving at high engine speeds or with a heavy load, or when driving while accel-
erating or decelerating frequently
●When leaving the engine idling for a long time, or when driving frequently through
heavy traffic
Engine oil selection→ P. 5 8 0
Oil quantity (Low → Full)1.5 L (1.6 qt., 1.3 lmp. qt.)
ItemsClean funnel
1
2
3
CT200h_OM_OM76135E_(EE).book Page 458 Friday, May 30, 2014 1 1:14 AM

4927-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
■Headlight low beams (halogen headlights)Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the headlight low
beams on once and visually confirm
that no light is leaking through the
mounting.
Replacing light bulbs
1
2
3
4
CT200h_OM_OM76135E_(EE).book Page 492 Friday, May 30, 2014 1 1:14 AM

4937-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
■Headlight high beams (halogen headlights) For the right side only: Move the
washer fluid filler opening.
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
1
2
3
4
CT200h_OM_OM76135E_(EE).book Page 493 Friday, May 30, 2014 1 1:14 AM

4947-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the headlight high
beams on once and visually confirm
that no light is leaking through the
mounting.
For the right side only: Reinstall the washer fluid filler opening.
■Headlight high beams (LED headlights)Turn the cover counterclockwise
and remove it.
Turn the bulb base counterclock-
wise.
Unplug the connector while pull-
ing the lock release.
5
6
1
2
3
CT200h_OM_OM76135E_(EE).book Page 494 Friday, May 30, 2014 1 1:14 AM

4967-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the fog lights on once
and visually confirm that no light is
leaking through the mounting.
2
3
4
5
CT200h_OM_OM76135E_(EE).book Page 496 Friday, May 30, 2014 11:14 AM

4977-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
Reinstall the fender liner with 2
screws, a bolt and clip.
■Front turn signal light s (halogen headlights)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
■Front turn signal lights (LED headlights)
XLeft side
Remove the power control unit
cover.
6
1
2
3
1
CT200h_OM_OM76135E_(EE).book Page 497 Friday, May 30, 2014 1 1:14 AM

4987-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
XRight side
Move the washer fluid filler opening. (→P. 4 9 3 )
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
2
3
4
1
2
3
4
CT200h_OM_OM76135E_(EE).book Page 498 Friday, May 30, 2014 1 1:14 AM

4997-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
■Rear turn signal lights Open the back door and remove
the covers and bolts, and remove
the lamp assembly by pulling it
directly backward from the rear
of the vehicle.
Use a flathead screwdriver wrapped
in a cloth.
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
■Back-up light/rear fog lightOpen the back door and remove
the cover.
Use a flathead screwdriver wrapped
in a cloth.
1
2
3
4
1
CT200h_OM_OM76135E_(EE).book Page 499 Friday, May 30, 2014 1 1:14 AM